Olá companheiros de cultivo! Esta semana parece que as plantas estão a desenvolver muito bem, estavam sob 20 horas de luz, reduzi horário para 18/6, e adicionei na semana passada bactérias que se chamam bactohemp e deu um óptimo resultado na vegetação de todas as plantas principalmente a shiskaberry, fiz LST para obter mais produção e estão a crescer galhos por todo lado nunca tinha visto uma planta assim 💪💪💪 espero que tudo dê certo estava com medo de ser macho porque estão a crescer galhos e mais galhos 😅 mas já apareceu uma pré-flor, a runtz muffin tb fiz LST tb está muito bonita a desenvolver muito bem, a BlueBerry OG também está uma planta muito forte, vou esperar mais uma semana para ver o desenvolvimento.. para depois pôr estas meninas a florir, obrigado amigos 💪💪🌳🌱🍀✌️

Haven't touched much of anything, and the roots are starting to find their way out of the basket.

Just PhD water. Think I'm burning em.

Farbenpracht. Meine 2te DNA Erfahrung. Und ich bin begeistert.

The start of the week is going well.Did some defoliation. Added a scrog net. I removed the scrog the next day, might use it if the buds need support. There’s no way to add the rabbit poo to the nutrients accurately all I did was top dress the soil with a few scoops and worked it in the soil lightly. Water with distilled water.

This is the beginning of each week. So I flushed them and switched nutrients. They were mag deficient, nitro toxic. Not PH actually. I'm adding co2 next week after I seal the room. I think I need to back the PAR down to 800 but they are still alive and it's over half way done. How any more weeks? I thought this was a 65 day auto. Hydro in a 5 gallon pot could add up to three weeks I heard with Autos. could these go 12 weeks total?

Eccoci qui... Settimana prossima si tagliaaaaa!!!! Finalemente siamo arrivati alla fine con questa piccola mi sono divertito è stato bellissimo coltivarla outdoor, è venuta bassa ma molto molto compatta!!! Grazie a tutti per il supporto

End of third week of flowering, all good :) besides small problems with SSH - little deficiencies of calcium. Also, again... I noticed some of mosaic virus on Power Plant They smell already a lot :) Lamp on 100% power, 35cm from closest bud, in the center 1300 - 1500 PPFD and on the sides around 1100 - 1300 PPFD - POWER!

Info in the video

Things are coming along here now, won’t be too much later for these plants. Probably start thinking about flushing 2 of them soon, I suspect the soil is loaded with a high ratio of nutes, think next time won’t use the high nute soil and go for total control. Already harvested one plant already, it was the smallest one, a bit early but she was milky and a few ambers, think she got me 25.55 dry in jar now. Letting the Others hit 50 % amber before harvest those. Two in back big stretch on them,the one left in front short and fatter, say she going next in a bit

Thanks Pyramid Seeds for your good genetics. Not my first experience with PS, like them so much. I was happy to grow this baby. It my first experience with coco. No pH or ppm meters, nothing just my eyes and feeling whole process. Thanks to ru brend Plantators for good feedings and stims for awesome price. You always can ask me about everything, I'm always in connection.

•••••••••••••••••••••••••• Sept. 26 - Oct. 2 Week 8 of 12/12 •••••••••••••••••••••••••• WEEKLY SUMMARY: •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 🙋‍♀️Fo' Twenny here!🙋‍♀️ We're back with another update on our 👴🏽💜 GRANDADDY PURPLE cultivar bred by BLIMBURN SEEDS! It's week 8 and all she is looking great as she progresses deeper into senescence; however, she is still a bit greener than either of her tent mates! She just seems to get frostier ❄️ by the day and her fragrance smells a bit sweeter than last time I ran her. I love her colors, the pink and yellow contrast is just beautiful! I keep checking trichomes, but still not a lot of amber. Maybe another week or more. Also, I realized my BlueLab Conductivity Meter has the option to switch to EC. Since EC is the most accurate way to measure the nutrient concentration in a solution, I will now be measuring and reporting EC readings rather than PPM. Any advice, suggestions, or constructive criticisms are always welcome. Now, for the weekly break down! •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• THIS WEEK'S BREAK DOWN •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 9/26 - Day 50 of Bloom °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° - Upgraded from 8k BTU to 14k BTU portable AC unit! - Light selective defoliation. 🌿 🚿FEED DAY!🚿 - She received approximately 2.5 gallons of nutrient solution. I mixed 8 gallons of solution for all the plants I have in flower. 2.5 gallons of that was then measured and fed to this cultivar. After 10-15 minutes I added additional 12 oz of plain H2O pH to 6.3 👩‍🔬NUTRIENT SOLUTION👩‍🔬 ⬇️Mixing Rundown⬇️ - The solution starts with 12 gal tap H2O through two kdf filters mixed in a 36 gallon reservoir. The solution is applied via wand sprayer powered by a submersible pump attached to a garden hose. Nutrients and additives are added to the reservoir in the order listed below and thoroughly mixed using a plastic stir spoon. The reservoir is oxygenated by four 4 inch air stones. Start pH: 7.9 PPM: 630 1.5 tsp/gal - Fox Farm BIG Bloom 1 tsp/gal - Fox Farm Tiger Bloom 1.5 tsp/gal - Fox Farm BEMBÉ .125 tsp/gal - Fox Farm Cha-Ching I always make sure pH is in the range of 6.0- 6.6 prior to adding any microbial innocclants. pH: 5.8 Add 1 tsp/gal General Hydroponics pH UP pH: 6.2 PPM: 1160 Mammoth P. - 0.6 ML/gal •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 9/30 - Day 54 of BLOOM °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° 📸 PHOTOSHOOT! 📸 🎥 FILMING! 🎥 •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 10/2 - Day 55 of BLOOM °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° 🚿FEED DAY!🚿 - She received approximately 2 gallons of nutrient solution. I mixed 6 gallons of solution for all the plants I have running in this SOG. 2 gallons of that was then measured and fed to this cultivar. This week I used some gallon bottles filled with water and frozen to lower temps in the reservoir. 👩‍🔬NUTRIENT SOLUTION👩‍🔬 ⬇️Mixing Rundown⬇️ - The solution starts with 6 gal tap H2O through two kdf filters mixed in a 36 gallon reservoir. The solution is applied via wand sprayer powered by a submersible pump attached to a garden hose. Nutrients and additives are added to the reservoir in the order listed below and thoroughly mixed using a plastic stir spoon. The reservoir is oxygenated by four 4 inch air stones. Start pH: 7.8 Start EC 1.0 TEMP: 69°F .75 tsp/gal - Fox Farm BIG Bloom .5 Tsp/gal - Fox Farm Tiger Bloom .75 tsp/gal - Fox Farm BEMBÉ .0625 tsp/gal - Fox Farm Cha-Ching Our target pH is in the range of 6.0- 6.6 prior to adding any microbial innocclants. pH already in range, no adjustments needed. pH: 6.5 (No adjustments needed) EC: 1.5 TEMP: 60 °F Mammoth P. .6 ML/gal •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• SUPPLIES & EQUIPMENT CURRENTLY IN USE: •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• • A/C: Whynter ARC-14S 14,000 BTU Dual Hose Portable Air Conditioner • TENT: VIVOSUN 48"x24"x60" Mylar Hydroponic Grow Tent with Observation Window & Floor Tray • POTS: Black 8"tall Active Aqua brand 6" x 6" one gallon square pots/Black 12" tall Active Aqua brand12" x 12" 3.4 gallon square pots • VEG/AUTOFLOWER INTAKE FAN: None (PASSIVE) VEG/AUTOFLOWER EXHAUST FAN : VIVOSUN 6 Inch 390 CFM Inline Duct Fan with Variable Speed Controller • BLOOM INTAKE FAN: VIVOSUN 6 Inch 390 CFM Inline Duct Fan with Variable Speed Controller • VEG/AUTOFLOWER EXHAUST FAN : VIVOSUN 6 Inch 390 CFM Inline Duct Fan with Variable Speed Controller • BLOOM EXHAUST FAN: AC Infinity CLOUDLINE T8, Quiet 8” Inline Duct Fan with Temperature Humidity Controller - Ventilation Exhaust Fan • VEG/AUTOFLOWER AIR MOVEMENT: 6-Inch Lasko FBA 2004W 2-Speed Clip Fan • BLOOM AIR MOVEMENT: One Honeywell TurboForce Air Circulator Fan Black, HT-900 and Three 6-Inch Lasko FBA 2004W 2-Speed Clip Fans • Bluelab PENPH pH Pen Fully Waterproof Pocket Tester • Bluelab PENCON Conductivity Pen Fully Waterproof Pocket Tester • Kolder Multi-Purpose Liquid and Dry Measuring Cup, 16-Ounce • Fox Farm Measuring Spoons • WATER TREATMENT: Tap H2O run through two AQUACREST Garden Hose Water Filters to remove chlorine and chloramine. – COMING SOON: Hydro-Logic 31023 1000-GPD Evolution RO1000 High Flow RO System, White (HL31023). • WATER APPLICATION: I use 2 different watering systems. The pump sprayer is typically used in early veg, between feeds, or for lighter feeds. Most feeds are usually run through the pump and reservoir because it's faster and easier when dealing with larger volume feeds. – 2 GALLON LAWN & GARDEN PUMP PRESURE SPRAYER. * I removed the spray head due to clogs and it's just faster. – Superior Pump 91250 Utility Pump, 1/4 HP in a heavy duty 27 gallon Tote attatched to a 10 foot garden hose to an Orbit Underground 56246 Green Thumb 9-Pattern Telescoping Wand. – Aeration of the reservoir is accomplished using a General Hydroponics HGC728040 Dual Diaphragm Air Pump 320 GPH 4 Outlet attached with standard aquarium air hose to four 4-Inch Air Stone Disc Bubble Diffusers. • VEG/AUTOFLOWER LIGHTING: 320w MosterBoard V4-PLUS powered by a MEANWELL 320H-48AB DRIVER. There are three V4-PLUS boards prewired and mounted on a 935x195x10mm black heatsink. Dimmer, UV Switch, and IR Switch included. Each board contains two hundred fifty two 3000k lm301h diodes + twelve Osram 660nm diodes plus 4 separately switchable LG UV 395nm diodes and 4 separately switchable Osram IR 730nm diodes. • BLOOM LIGHTING: Two custom mounted lighting units: Each mount has one 480w MEANWELL 480H-48B driver and one 240w MEANWELL 240H-48AB powering 6 KingBright Quantum Boards. Each board contains two hundred fifty two 3500k lm301h diodes + twelve CREE XP-E2 660nm diodes plus four separately switchable CREE XP-E2 730nm diodes and four LG UV 395nm diodes. Hanging between the two mounts are two additional quantum boards with two hundred fifty two 3000k lm301h diodes + twelve 660nm diodes plus four constant power 730nm IR diodes and four 395nm UV diodes. That's a total of 1680 watts of quantum board power in our 96" x 48" bloom tent! ⚠️ ALL DRIVERS MOUNTED REMOTELY IN AN AIR COOLED BOX INSTALLED BETWEEN THE FILTER AND EXHAUST FAN ⚠️ • SLMOTO Universal Oil Drain Pan, 2 Gallon (8 Liter) Capacity ABS Low Profile Oil Drain Pan w/Spout Fit for Motorcycles • Modified Botanicare Low Tide LT Black Tray - 4' x 4' - Modification: Cutaway at corners and used flex-seal tape to create a new edge that will be soft to fit between tent supports. She is supported by 6 Standard Cored Concrete Blocks (Common: 4-in x 8-in x 16-in; Actual: 3.625-in x 7.625-in x 15.625-in). ⚠️THIS TRAY WILL NOT FIT BETWEEN SUPPORTS IN A 48" x 48" or 48" x 96" TENT WITHOUT MAKING MODIFICATIONS TO THE TRAY!⚠️ • Blue Sticky Pads • Yellow Sticky Pads •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• SOIL MIX DETAILS: •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• All components were mixed into a 50 gallon tote that is kept in a warm environment to help innocculate to promote a vast and diverse microbial life in the rhizosphere. Once mixed, add 32-64oz water once every 7-14 days as needed. The goal is to keep the soil moisten without oversaturating. 2 Part - Royal Gold Tupur INGREDIENTS: Coco fiber, aged forest materials, perlite, and basalt 1 Part - Fox Farms Ocean Forest INGREDIENTS: Aged forest products, sphagnum peat moss, earthworm castings, bat guano, fish emulsion, and crab meal. 1 Part - Roots Organics INGREDIENTS: Perlite, Coco Fiber, Peat Moss, Composted Forest Material, Pumice, Worm Castings, Bat Guano, Soybean Meal, Alfalfa Meal, Fishbone Meal, Kelp Meal, and Greensand. Also contains beneficial mycorrhizal fungi: Funneliformis mosseae, Rhizophagus intraradices, Septoglomus desertícola .5 Part - Wiggle Worm Soil Builder Pure Earthworm Castings .5 Part - Ancient Forest Humus .5 Part - Coarse Grade Perlite Inocculated by mixing 1 cup of Extreme Gardening Mycos Watered with pH 6.5 h2O 1 Tsp/gal Real Grower's Recharge 1 tsp/gal Hi-Brix Molasses 2 tsp/gal Fox Farms Kangaroots •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Want to see more cultivars I have growing❓ Please, be sure to check out my other diaries & give me a follow! 👍👍 🙏Thank you for stopping by my garden!🙏 Peace, ☮️✌️ Love, 💚🤟 & Frosty Nugs! ❄️🌲 Happy farmin' my friends! ☺️🌱 - Fo' Twenny 👩‍🌾🏻

Buds are starting to stack up, increased PH to 6.2 for a better Kalium Uptake, lowered the nitrogen to 100ppm since the plants seem to be slightly high on it.

So loud the air taste like strawberry shortcake haha terps are super rich they stay on you, Kush as cologne!

It's been an exciting journey training my plants, and I'm happy with the progress they've made. I've been implementing various training techniques to encourage healthy growth and maximize yields. The plants have responded positively to the training, and I'm hopeful that they will continue to thrive and develop as planned. Fingers crossed for a successful outcome!

Hello. I've harvested the Mega Mouth. WOW!!! I'm very impressed with this strain. Over 1.5 k for 5 plants. and it was finished by Aug 20 with the tents help. I'm trying some new (for me) categories to add to my report. Plant Stretch (PS) 1 to 5- 1 is hardly any stretch. Bud Mutation (BM) 1 to 5- 1 is a beautiful normal bud- 5 is big weird growths like foxtails. Trim- How easy or hard it was to trim up 1- you blow on the branch and hang it up. 5- Is very hard to trim takes a long time. About- Best guess on the THC % (I've been smoking a long time) Resin- 1 is super slippery 5- is very sticky like Gorilla Glue. Size of Buds (SOB) 1- is very small 5- is the biggest buds Dense- 1- is the lightest or fluffiest 5- is the rock hard buds your bud buster has trouble busting up. Plant #1 Wet Trim 1647 g PS. 3.5 BM 3.5 Trim 4 About 21% Resin 4 SoB 4 Dense 4 Finished Dry Weight 289.5 g or 10.33 oz. Plant #2 Wet trim 1606 g PS 3,5 BM 3.9 Trim 4 About 22% Resin 3 SoB 4.7 Dense 4.3 Finished Dry Weight- 302 g or 10.78 oz. Plant #3 Wet Trim 1635 g PS 3.7 BM 3 Trim 2.8 About 20% Resin 2.8 SoB 3.7 Dense 4.5 Finished Dry Weight- 314 g or 11.21 oz. Plant #4 Wet Trim 1753 g PS 2.5 BM 2.5 Trim 3 About 22% Resin 4 Falls off easily- Clumpy Dense 2.5 Final Dry Weight- 343.5 g or 12.26 oz. Plant #5- Wet Trim 1787 g PS 3.5 BM 3.7 Trim 3 About 24% Resin 2.5 Dense 2.5 Finished Dry Weight- 355.5 g or 12.69 oz. The taste is sweet and smooth to go down with a nice balanced buzz. There was some pests around. I found thrips damage in veg and got some Spinosad to take care of that. Saw some fungus gnats around but they didn't do much damage. Easy to grow and trim. This is a recommended strain. Chuck.

If you run coco coir it's a must

Like I said normal difficulty but good resistance at the same time. Similar to an OG kush kinda. Sampled some already great smoke decent flavor considering it’s not cured yet. It still needs a day or 2 to dry as well but won’t cure it as I need weed soon. Hope y’all liked it and hope u look at my primary grow which is my 5x5 gorilla grow tent with a viparspectra ks5000 515 watt led light with full equipment including ac unit and DIY co2.