Likes
14
Share
@danwho
Follow
8/14/2024 Topped plant A due to the node spacing and side branching. Hopefully, this will cause this pheno to bush out a bit more. Intentionally FIMed plant B due to the short internodal spacing and difficulties getting a clean cut for a topping. This plant is already quite bushy and condensed - hoping that it will respond nicely to FIM. Water was not changed over entirely, only added one fresh gallon of nutrient water with additional nutrients added to step up entire system to close to 575-600ppm. Both plants are looking great, root zone needs some improvement with water temperatures. I have ordered a larger water cooler and hope that will help reduce the water temperature inside the tent. Although water temps are a bit high in the buckets, the roots are flourishing and are pearly white! 8/16/2024 Noticed Plant A is showing signs of potassium issues. Added one fresh gallon of non-nutrified water as I was unable to complete a water change. 8/17/2024 Pumped out 5 gallons of nutrient water and refreshed with 5 new gallons. Both plants look to be responding well to the water change. The resulting PPM was 650 after allowing time for the system to reach equilibrium. Extra insulation on the buckets is helping to maintain lower water temperatures throughout the day with lights on in the tent. The environment is pretty well dialed in at an average 1.2-1.6 VPD. 8/19/2024 Replaced water cooler with one that is twice the size and rated for 15-gallon systems. Running reservoir temp target at 18.5 C. Conducted some minor LST on the bushy plant (Plant B) to get the middle opened up a bit more. Did some leaf tucking on plant A to get the lower branches some more direct light. 8/20/2024 Both plants are looking phenomenal. There is a very slight cannabis smell in the tent at all times.
7
40
Share
@BLAZED
Follow
Week 16 (Harvest) 1-2 Drying day 1 Temperature: 24.5 to 19.5 degrees Humidity: 65% to 50% The girls are ready to be harvested! Before chopping them down, i took a lot of pictures. I was able to remove most of the soil from the Biscotti #2 to see the rootball. I hang the plants as a whole to have a slow dry. The exhaust fan is on setting 4. 2-2 Drying day 2 Temperature: 19.1 to 17.5 degrees Humidity: 62% to 57% I changed the exhaust fan to setting 2 because setting 4 was a bit high in my opinion. 3-2 Drying day 3 Temperature: 19.9 to 18 degrees Humidity: 62% to 59% Today i checked up on the drying plants, and i see there are some buds touching other buds, so i chopped the plants in half. The buds are still to the main stem for a slow dry, but are hanging more spreaded out to prevent any budrot issues. I changed the exhaust fan to setting 1, as someone told me that it was enough air movement for drying. 4-2 Drying day 4 Temperature: 19.8 to 18.5 degrees Humidity: 62% to 59% 5-2 Drying day 5 Temperature: 19.9 to 18.8 degrees Humidity: 62% to 59% Today i checked on the drying plants and the buds are shrinking a bit, they are getting a little bit crispy on the outside aswell, I hope they wont dry as fast, and i aim for a 12/14 day dry. For the next grow i already germinated 2x Chemdog (GreenHouseSeeds) 2x Gorilla Kush (GanjaFarmerSeeds) and 1x Deep Candy CBD (GreenHouseSeeds) And I have some upgrades planned aswell! I bought a autopot kit with 4 15L pots, this way the plants will have water and air 24/7 whenever they need it. I have seen alot of great results using autopots so i am very exited to try it out! And I bought a small camera so i can shoot some weekly timelapses! Feel free to Follow me if you like to get notified for the upcoming diaries! Thanks for checking out this diary, peace! (More harvest updates coming in the next couple of days!) Huge thank you to Zamnesia for the seeds, and Plagron for the collection of nutrients, and the opportunity to participate in the POWERBUDS contest! It was a fun and learningful adventure!
4
13
Share
@SgtDoofy
Follow
April 11 Just got done with some serious defoliation. Removing all kinds of nodes that would have wound up as less than popcorn bud while taking up valuable space in the light. Some of the tips of the leaves up top got sacrificed as I waited to feed for a bit too long while I wanted for a calmag solution to be delivered. Little ugly, but no worse for the wear.
4
3
Share
Used Gaia Green Bloom to Top dress about Week 3 of flower Introduced a couple Pluto runtz Plants in the front Cause they accidentally Flowered 🤷‍♂️
1
8
Share
The plant is starting to show signs of early bud sights, and producing large fan leafs as well as good healthy gassy smell
1
31
Share
La aventura ha acabado antes de lo esperado, entre las condiciones climáticas y el ataque de un jabalí 🐗 han acabado con este proyecto, la próxima vez será 😃
1
3
Share
@Franco123
Follow
Hi today I realized that the plant is a male, and it came out autoflowering being an f2 of DonDiablo that in F1 a cross of a photodependent female and an autoflowering male there was a 25% chance that it develops if an autoflowering, but or decided not to keep it because I don't like autoflowering plants very much and I want to get it to become competent photodependent so later I will put other seeds in the hope that they come out photodependent
3
21
Share
2
2
Share
the growth , the growth , the growth i have seen nothing but good thing from fastbuds the smell is starting to ripen and fill tent nice and dense nuggets are def inbound leaning to the side after ties was removed from heavy lst
6
25
Share
3
102
Share
@Aleks555
Follow
Dear team TrolMaster Europe, We would like to express our sincere gratitude for providing us with the Tent-X controller. We are delighted with its functionality and performance! We are confident that this controller has significantly aided us in our journey with our beloved plant Jealousy from Zamnesia.💪🤝 We were pleasantly surprised by the efficiency and ease of use of the Tent-X. It seamlessly integrated into our plant care system and helped us achieve incredible results. Once again, thank you very much for your support and high-quality equipment. We are immensely satisfied with your product and hope for long-term cooperation in the future. Today marks the end of our journey with Jealousy from Zamnesia💚, and we want to express our heartfelt gratitude to Zamnesia for their support throughout this entire journey. We also want to extend our thanks to Plagron for providing us with their high-quality fertilizers. Their products are not only effective but also incredibly easy to use. We highly recommend them to everyone!