Advanced Seeds: Auto Strawberry Gum

NoLimitQ Advanced Seeds Auto Strawberry Gum. The autoflowering version of our Strawberry Gum. It has retained the wonderful strawberry aroma, as well as a high yield of buds and resin. With it, you'll achieve a cerebral and euphoric effect so pleasant that you'll fall in love with it. This is an energetic and low-maintenance plant with a high terpene content. The box is assembled and slightly modified. In general, here's what we have: a box measuring about 50*60*120 cm (L*W*H). At the top - a technical compartment: timer, power supply from a computer for 12V fans (2 for airflow, 1 for air intake into the box, and 1 for exhaust through the biparabolic reflector), sockets, timer, and a 100 mm duct fan for exhaust. I ordered a thermostat and humidity controller from AliExpress - STC-3028. For heating the box at night, I use an infrared heater Ballu BIH APL-0.6. The ballast + HID + capacitor from the HPS is located outside the technical compartment to avoid overheating inside. Lighting for veg: 1 CFL lamp 105W 6500K. Lighting for flowering: CFL 105W + HPS 400W lamp. The grow room is lined with foam foil, and the doors are sealed with a gasket: a 20L pot, a 2.5L humidifier. Soil - BioBizz All Mix 20L, mixed with 2L of vermiculite. GHE nutrients: Flora Series Tripart (I took 60 ml each) + ProRoots + ProBloom + Fulvic + Rirpen also from GHE. For adjusting the pH of the water: pH Down and pH Up from E-Mode. While there is snow outside, I melt it and filter it. Watering with melted water. 01/12 I dropped 2 seeds into a glass of water. 01/13 Soaking in a damp cotton disc. Water - melted snow. I put it in a drawer in a dark place. The cotton disc is on a plate, and the plate is in a bag. 01/14 Waiting for the seeds to sprout 0.5 - 1 cm. 01/15 Planting the sprouted seeds in the soil. I pre-watered with about 1.5 liters of water + 0.3 ml of Pro Roots from GHE, moistening the dry soil. Covered with cups, spraying inside with melted water. Temperature - 21 degrees. The light in the box is on 24/0 for the first while. 01/16 In the morning, the first seed sprouted about 1 cm, I helped remove the helmet. Sprayed with a spray bottle. In the evening, the second seed sprouted. The distance from the lamp to the plant is 12 cm. 01/17 In the morning, I removed the protective cups. In the evening, the thermostat and humidity controller arrived, and I installed them. 01/18 I set up the heater opposite the box. It works by sensor - I set the temperature to 22-23 degrees. Spraying with melted water from a spray bottle. The humidifier will arrive tomorrow. I set the sensor to 50-60%. 01/19 Starting the count for veg today and setting the timer to 20/4. 01/20 Watering with melted water 0.5 L + pro roots 0.1 ml. 01/21 Spraying with melted water from a spray bottle. 01/22 Spraying with melted water from a spray bottle. 01/23 Watering with melted water 0.5 L + pro roots 0.1 ml. 01/24 Diluted 0.5 L of melted water with pro roots 0.1 ml and gave it to the leaves. 01/25 Gave pro roots to the leaves. The first week is complete. We're growing and developing =) Starting tomorrow, I'll switch the timer to 18/6.

NoLimitQ 26.01 Added about 4 cm of coconut, lowered the plants a bit further from the lamp. Sprayed with pro roots solution. 27.01 Watered 0.5 L of water + 0.1 ml Pro Roots + 1 ml Fulvic, adjusting the pH to 5.6, ppm=40 28.01 Sprayed with pro roots solution. Some burnt tips appeared on the first leaf. 29.01 Spraying with melted water 30.01 Spraying with melted water 31.01 Spraying with melted water, lowered the plants another 10 cm from the lamp 01.02 Watered with melted water 2 L + bio roots 0.4 ml + fulvic 4 ml. Spraying with a spray bottle of melted water. Took measurements: pH before watering = 6.4, after watering = 6.5. ppm before watering - 16, at the runoff - 5300 - Some crazy stuff) even though I didn't feed with fertilizers. Small branches started to break through from the nodes and sexual characteristics appeared on one plant. The second week is complete. We're growing and developing. Peace!

NoLimitQ 02.02 I turned on the HPS 400, lowered the plant down, now the distance from the lamp is about 40 cm. The temperature in the box is 27.8 degrees, humidity - 50-55%. I made a solution for spraying - 1 liter of melted water + 3 ml Fulvic, I will be spraying it. 03.02 I’m starting to do LST training. I bent the plants and secured them with wire. Sprayed with Fulvic solution. 04.02 I continue doing LST training. Spraying with Fulvic solution. 05.02 I bought another timer for the HPS. I set it so that the CFL 105W lamp turns on first, and after half an hour - the HPS 400W, so it’s like morning and then day. Also for turning off - half an hour before the lights go out in the box, the HPS turns off. Plus, we save 400W a day. I continue doing LST - spreading the branches and opening them for better lighting, bending them to the ground with wire. Every time I check the box - I spray with Fulvic solution (3 ml/liter). Watering with melted water 3L + 6 ml Fulvic + 0.6 ml Pro Root GHE. ppm at the input - 20, at the output - 2300. pH at the input - 6.4, at the output 6.9. 06.02 I continue doing LST training. Spraying with Fulvic solution. 07.02 I continue doing LST training, securing the branches and leaves with wire. Spraying with Fulvic solution. 08.02 The 3rd week has come to an end - we're growing and developing! I continue doing LST training, securing the branches and leaves with wire. I try to keep the plant at the same level. Spraying with Fulvic solution.

NoLimitQ 09.02 Did LST, secured the branches with wire, spraying with Fulvic solution. Another watering tomorrow, then I’ll start feeding with GHE nutrients. 10.02 Watering with melted water 2 L + 4 ml Fulvic + 0.4 ml Pro Root GHE. Continuing LST training. Spraying with Fulvic solution. 11.02 Continuing LST training. Spraying with Fulvic solution. 12.02 Continuing LST training. Spraying with Fulvic solution. 13.02 Continuing LST training. Spraying with Fulvic solution. Set humidity a bit lower at 41-45%. Pre-flower is about to start, white hairs are beginning to form on the tips of the branches. 14.02 Continuing LST training. Spraying with Fulvic solution. 15.02 Continuing LST training. Spraying with Fulvic solution. Tomorrow will be the first feeding with nutrients. Week 4 of the vegetative stage has come to an end, we’re growing and developing!

NoLimitQ 16.02.22 I will water every other time: nutrients/water/nutrients/water... and so on. I make a solution with 3.5 liters of water: MGB=6.9/6.9/4.6. Added Pro Bloom 0.7 ml and Fulvic 7 ml, got pH=5.5 and ppm=750. I took out all the ties made of copper wire. Did DEFOLIATION. Watered with GHE solution, forgot to measure pH and ppm at the end, and reinserted the wire, distributing the branches a bit differently. Slightly damaged the main cola on one plant by bending it quite a bit, but it's not critical. The branches are not growing very fast, but I hope they will stretch soon and have huge buds =) Sprayed with Fulvic solution from a spray bottle. 17.02.22 Continuing with LST training. Spraying with Fulvic solution. 18.02.22 Continuing with LST training. Spraying with Fulvic solution. 19.02.22 Continuing with LST training. Spraying with Fulvic solution. 20.02.22 Starting the flowering countdown. Continuing with LST training, bending the branches at the same level with copper wire. Spraying with Fulvic solution. Watering with melted snow water 2L + Fulvic 4ml + Pro Bloom 0.4 ml. Made and installed a SCROG with a 5 cm cell. 21.02.22 Day 2 of flowering. Bought a carbon filter for 160m3 and a new Typhon duct fan for 250m3, turned it on to speed 1. Spraying with Fulvic solution. 22.02.22 Day 3 of flowering. Spraying with Fulvic solution. During the day, the temperature stays around 26-28 degrees, humidity about 40%. At night - temperature around 20 degrees, humidity 45%.

NoLimitQ 23.02.22 Day 4 of flowering. Spraying with Fulvic solution. 24.02.22 Day 5 of flowering. Removed the wire, spraying with Fulvic solution. We're making a solution for 4 liters of water: MGB=7.92/5.28/7.92 + Fulvic 8ml + Pro Bloom 0.8ml. 25.02.22 Day 6 of flowering. Spraying with Fulvic solution. 26.02.22 Day 7 of flowering. Spraying with Fulvic solution. Removed the scrog and trimmed the lower leaves and branches, redistributed the colas a bit, reinserted the support wire. Removed some upper leaves to allow light to reach the lower branches. 27.02.22 Day 8 of flowering. Spraying with Fulvic solution. 28.02.22 Day 9 of flowering. Spraying with Fulvic solution. Today the temperature during the day was ~20 degrees, voltage in the network is fluctuating + I forgot to close the window, and it's -5 degrees outside. Watering with melted snow 3 liters + 6 ml Fulvic + 0.6 ml ProBloom. 1.03.22 Day 10 of flowering. Spraying with Fulvic solution. Trimmed a few leaves to free up the lower branches for light access. Week 6 is complete - we're growing and developing =)

NoLimitQ 2.03.22 Day 11 of flowering. I'm spraying with Fulvic solution. 3.03.22 Day 12 of flowering. I'm spraying with Fulvic solution. I trimmed a few leaves to free up the lower branches for light access. 4.03.22 Day 13 of flowering. I'm spraying with Fulvic solution. We're making a solution for 4 liters of water: MGB=9.24/3.96/9 + Fulvic 8ml + Pro Bloom 0.8ml. 5.03.22 Day 14 of flowering. I'm spraying with Fulvic solution. I'm bending some of the stretching branches under the SCROG net. 6.03.22 Day 15 of flowering. I'm spraying with melted water from the sprayer. 7.03.22 Day 16 of flowering. I'm spraying with melted water from the sprayer. 8.03.22 Day 17 of flowering. I'm spraying with melted water from the sprayer. Week 7 is complete - we're blooming and smelling great.

NoLimitQ 09.03.22 Day 18 of flowering. Spraying with melted water from the sprayer. 10.03.22 Day 19 of flowering. Spraying with melted water from the sprayer. Watering with melted water 4 L + Pro Bloom 0.8 ml + Fulvic 8 ml. 11.03.22 Day 20 of flowering. Spraying with melted water from the sprayer. 12.03.22 Day 21 of flowering. Spraying with melted water from the sprayer. 13.03.22 Day 22 of flowering. Spraying with melted water from the sprayer. 14.03.22 Day 23 of flowering. Spraying with melted water from the sprayer. I trimmed a few leaves to free up the lower branches for light access. 15.03.22 Day 24 of flowering. I’m making a solution for 4 liters of water: MGB=10.6/2.64/10.6. pH=5.65, ppm=970. Stopping the ProBloom and Diamond Nectar. Trimmed a few fan leaves. Spraying with melted water from the sprayer. Week 8 is successfully completed. The buds are starting to swell, and that’s definitely exciting =)

NoLimitQ 16.03.22 25th day of flowering. I'm spraying with melted water from a spray bottle. Late flowering stage. 17.03.22 26th day of flowering. I'm spraying with melted water from a spray bottle. 18.03.22 27th day of flowering. I'm spraying with melted water from a spray bottle, tomorrow I'll water without nutrients, using melted water with stable pH. 19.03.22 28th day of flowering. I'm spraying with melted water from a spray bottle. 20.03.22 29th day of flowering. Watering with melted water, 3 liters, pH=6.5 ppm=10. I'm spraying with melted water from a spray bottle. 21.03.22 30th day of flowering. - 22.03.22 31st day of flowering. Completed the 9th week from germination. The buds are swelling, today I tried the lower branch in water. It's already taking quite well =) We're growing, blooming, and developing =)

NoLimitQ 23.03.22 - 24.03.22 We're making a solution for 3 liters of water: MGB=9.93/1.98/11.91. pH=5.8, ppm=1020 25.03.22 - 26.03.22 I removed 2 lower loose branches, they weren't getting any light. I moved the fans to a different spot for better airflow around the plant. 27.03.22 - 28.03.22 Watered with melted snow, 1.5 liters, pH=6.5 ppm=10 29.03.22 Week 10 is done, the buds are getting bigger and the smell is getting stronger! But the carbon filter is doing great. We're flowering and smelling good =)

NoLimitQ 01.04.22 Preparing a solution for 4 liters of water: MGB=13.24/2.64/15.28. pH=5.5, ppm=800. This is the last time I'm watering with nutrients. 02.04.22 Removed the yellow leaves. 03.04.22 Spraying with melted water from the spray bottle. 04.04.22 Spraying with melted water from the spray bottle. Removed yellow leaves. Took a look at the buds under the microscope - they're maturing!) Trichomes are increasing every day, there are a lot of clear ones now, but the end is near - about 3 weeks left. The plants have different phenotypes: the one on the left has purple hues on the leaves. The one on the right was greener, now the leaves are just yellow. Although, maybe the placement near the lamp and humidifier also affects it. The right strawberry plant is very close to the humidifier, while the left one is under a bright 400W HPS at 35 cm. 05.04.22 Watering with melted water, 3 liters, pH=6.5, ppm=10. Week 11 is complete. Nutrient watering is finished. Next, I'll be watering with ripen solution. The buds are big and smell delicious =)

NoLimitQ 09.04.22 I removed the SCROG and redistributed the branches a bit, securing them with wire to the ground. The plant is nearing the end of its cycle. About two to three weeks left. I’ll be watering with the ripen solution every other day, 1 liter at a time. The last 2 times I’ll water with settled melted water, and then it’ll be drying and flushing. Watering 1 L of water + 4 ml of ripen, pH=6, ppm=700 11.04.22 Watering 1 L of water + 4 ml of ripen, pH=6, ppm=700 12.04.22 The 12th week is complete. The plant is no longer growing upwards - now the buds are just swelling. I’m watering with ripen every other day. I’m slowly smoking the little lower buds =) they’re doing pretty well.

NoLimitQ 04.15.22 Watering 1 liter of Ripen solution 4 ml/l 04.17.22 Watering 1 liter of Ripen solution 4 ml/l 04.19.22 Watering with Ripen solution: 2 liters of thawed water + 8 ml Ripen. Next watering with water to wash out the taste of fertilizers (in the end, I didn't do this and finished with Ripen). Next - darkness and harvest =) 13th week completed.

NoLimitQ 23.04.22 Watering with Ripen solution 2 L of thawed water / 8 ml Ripen. In 3-4 days, when the plant finishes the last portion of Ripen, I will turn off the light for 1-1.5 days - preparing the plants for harvest. 26.04.22 Week 14 is complete. Harvest is very close - next week. Tomorrow, April 27, I will turn off the light in the box for a couple of days. At the same time, I will slowly start taking the equipment out of the box. On April 29, there will be manicuring and drying of the plant. I will dry it in the same box where the plants grew. In the last few days, I stripped the lower branches and smoked them, leaving the plant only with beautiful and juicy top buds. The stuff is hitting nicely! =) After the cure, it will be even tastier!

NoLimitQ The harvest is complete. Total: from seed to harvest it took 107 days (including 6 days for germination). I will dry the harvest in the same box where the plant grew. Temperature 16-20 degrees, humidity 20%. Next, it will be cured in the freezer. I will add information about the quantity a bit later.