lased First, the seeds were placed in a glass with reverse osmosis water, in the dark, for 12 hours.
Then, they were transferred to a container with damp paper and kept in the dark inside a drawer for 3 days. At the end of this time, the roots of the seedlings had grown approximately between 2.5 and 3.5 cm.
Next, I transplanted the seedlings into rock wool cubes that had previously been soaked for 15 minutes in the nutrient solution from the RDWC system. After this, I placed them in the pots and put them into the system. When inserting them, I made sure that the bottom of the rock wool cube was in contact with the water. I surrounded the cubes with expanded clay and added a layer of approximately 0.5 cm thick at the base of each cube to promote hydration and drainage.
It's important to note that the amounts of nutrients applied were not exact, as I experienced difficulties with the pH and water temperature.
2 likes
comments
Share
Used method
Paper Towel
Germination Method
1
Week 1. Vegetation
2y ago
1/25
6 cm
Height
18 hrs
Light Schedule
24 °C
Day Air Temp
5.6
pH
No Smell
Smell
355 PPM
TDS
75 %
Air Humidity
24 °C
Solution Temp
21 °C
Night Air Temp
34 liters
Pot Size
54 cm
Lamp Distance
Nutrients 2
TriPart Micro
0.528 mll
TriPart Bloom
1.057 mll
lased I've been having problems with the water pH all week, due to an issue I had with the rock wool, which broke down a bit and contaminated the system.
1 like
1 comment
Share
2
Week 2. Vegetation
2y ago
1/17
9 cm
Height
18 hrs
Light Schedule
26 °C
Day Air Temp
5.6
pH
No Smell
Smell
550 PPM
TDS
65 %
Air Humidity
20 °C
Solution Temp
21 °C
Night Air Temp
34 liters
Pot Size
54 cm
Lamp Distance
Nutrients 2
TriPart Micro
1.08 mll
TriPart Bloom
2.16 mll
lased Light at 50% power
WATER CHANGE
The system has been emptied. It has been cleaned with paper and filled and emptied 2 times with 25 liters of osmosis water, with everything running to clean it all a bit.
The water level has been lowered; the hydroponic system contains around 66 L of osmosis water.
10 ml of Orca Liquid Mycorrhizae has been added after nourishing and adjusting the pH of the water.
1 like
2 comments
Share
3
Week 3. Vegetation
2y ago
1/18
20 cm
Height
18 hrs
Light Schedule
26 °C
Day Air Temp
5.7
pH
Weak
Smell
650 PPM
TDS
56 %
Air Humidity
20 °C
Solution Temp
19 °C
Night Air Temp
34 liters
Pot Size
50 cm
Lamp Distance
Nutrients 2
TriPart Micro
1.42 mll
TriPart Bloom
2.85 mll
lased Light at 75% power
WATER CHANGE
The system has been emptied. It has been cleaned with paper and filled and emptied 2 times with 25 liters of osmosis water, with everything running to clean it all a bit.
The water level has been lowered; the hydroponic system contains around 66 L of osmosis water.
10 ml of Orca Liquid Mycorrhizae has been added after nourishing and adjusting the pH of the water.
The plants have a phosphorus deficiency, which will be attempted to be corrected with the next water change.
1 like
comments
Share
4
Week 4. Flowering
2y ago
1/5
20 cm
Height
18 hrs
Light Schedule
26 °C
Day Air Temp
5.8
pH
Weak
Smell
800 PPM
TDS
52 %
Air Humidity
20 °C
Solution Temp
19 °C
Night Air Temp
34 liters
Pot Size
40 cm
Lamp Distance
Nutrients 2
TriPart Micro
1.37 mll
TriPart Bloom
3.49 mll
lased Light at 75% power
WATER CHANGE
The system has been emptied. It has been cleaned with paper and filled and emptied 2 times with 25 liters of osmosis water, with everything running to clean it all a bit.
The water level has been lowered; the hydroponic system contains about 66 L of osmosis water.
10 ml of Orca Liquid Mycorrhizae has been added after nourishing and adjusting the pH of the water.
The pH level has been raised to 5.8 and more TA Bloom nutrients have been added to compensate for the lack of phosphorus.
@NiceCrits, yes, I made them with 5mm EVA foam. I measured the inner diameter of the top of the pot, made circles, and cut them out. Finally, I made a small hole in the middle. 👍 I usually make one more than I need, just in case 😁
Hi, sorry for my bad Spanish. The girls will be beautiful. I'm currently setting up a system like this with 6 buckets. I would like to know if what you wrote, Tripart Micro 1.08ml and Tripart Bloom 2.16ml, is added per liter. So, a total of 66 x 1.8 ml or 66 x 2.16 ml? Thanks for answering my question.