Drip Emitter Flow Rate HTP159W

WillyMacMusic
WillyMacMusicstarted grow question 2d ago
Why are my RainPoint Drip Emitters reducing my flow from 450 ml/minute to around 50 ml/minute? I love the wi-fi controller, and the pump delivers almost exactly what they promise, but the emitters drop my flow significantly! Any thoughts? Hand watering again 😞
Open
Week 4
likes
Answer
greenAF
greenAFanswered grow question 2d ago
thats the whole point of a drip systems. slow measured feeding. higher flow rates drastically increase the chances of channeling. I use .3GPH drippers 3x for 2g pots or 1x for 1g pots. I would not use anywhere near 450ml/min flow specially not via 1 drip line in a large pot. your not going to get an evenly saturated substrate or a consistent ec distribution. Not saying you cant make it work but thats not how I would use a drip system.
1 like
Complain
00110001001001111O
00110001001001111Oanswered grow question 2d ago
There's flow and then necessary pressure. Both are kinda like a currency when you design a system... length of tubing, number of emitters, bends in tubing, elbows, splits etc etc all impact flow and pressure. You need an excess of each, and some emitters require more psi to function properly than others, but they provide a consistency and convenience that is worth it. Assuming delivery lines have enough flow for all the emitters in use, If you bought a typical aquarium pump, it's probably lacking pressure (also can infer from "lift" specification) to push all your emitters and the water through the tubing (resistance etc). -------------------------- pressure-compensating drippers are the way to go... no concern about emitter flow oscillating, but you generally will need 12-16 psi to push them - in addition to the psi lost to the outflow of those emitters and overcoming resistance in the line or lift getting the water to them. The non-pressure compensating stuff will also fluctuate when anything changes -- like shutting off a pot because it harvested sooner than the others... that will change the flow and pressure to everything else requiring a domino of adjustments to re-callibrate everything. Any sort of gunk interfering with 1 emitter will impact all other emitters etc etc.. The other thing to consider is the max flow of your lines. 1/4" ID can only handle so much water, so if a 1/4" line is split in any way or the emitters have higher requirements, you'll have issues. Think 1/4" maxes out at 30gph? the smaller 1/2" lines (multiple sizes exist that are called "1/2" ") caps out a little over 200gph... there are charts for this based in inner diameter. This is about all the flow added up from the emitters on that line and all the reseistance that reduces max flow from pump -- then you kinda do the same math for pressure too. Get the RV booster pumps if you use pressure-compensating or have a large system. Aquarium pumps are severely limited.. they are more about maximizing flow under minimal resistance. You generally need a pump with decent "lift". Kinda like the difference between a good inline duct fan vs those really cheap in-line aluminum ones that lose most of their cfm with any amount of resistance (static pressure).. "170 cfm" until it's hooked up to 8' of duct and that turnes into 20cfm, lol. Same with those aquarium pumps.. 1000gph flow but at just 6-10' of lift or equivalent resistance and that 1000gph quickly turns into 0 GPH. Thise drippers are supposed to be a slow flow, eh?... so it may be their design to cap out at 50ml/minute? after a couple failed attempts at making an irrigation system here's my suggestions... -The most simple design possible will limit the the cost to pressure and flow related to delivering the water to the emitters.-Avoid spaghetti line (1/4") .. it's garbage. Stick to 1/2" for anything going to the pots.-Avoid manifolds with 'adjustable flow' -Get an in-line pressure limiter .. the adjustable, brass ones with built-in pressure meter are worth the extra 5 dollars than the static 30psi limiters. -Use pressure compensating emitter options. -Use the RV pressure boosting pumps.. typically listed as 45-60psi or even higher (adjutable). They aren't meant to run for a long time, but shouldn't take more than 10mins to water anyway. -Don't skimp on emitters per pot.. if max flow becomes an issue, go with lower GPH emitters to compensate. You don't want consistently dry zones of medium. -Have a shut-off per pot so you can harvest individual plant as necessary -- also where that pressure limiter is necessary. -For any larger reservoir capacity, use power heads, not airstones. -Tea bag the reservoir with a "Bti" dunk. Use a 1/4 dunk at a time to make them last longer. Mesh keeps your plumbing clean. -If running straight from tap, use check valves or if gravity will cause your entire reservoir to empty etc. -Shut-off valve at start of irrigation lines/loop. This is nice for taking it apart to store or maintenance etc. I don't have to worry about the leftover water in the line as i disconnec the hose from pump from irrigation loop. -Obviously, any sort of drain basin with a float-switch pump to handle runoff... -Design in a way that's easy to add and remove to a pot... e.g. if it has to fit over a plant, makes it impossible or difficult to add to a larger plant. pressure limiter makes sure when you start shutting things down you don't have any blowouts... a system built to handle 8-12 pots wating 1-2 pots can be a real problem. But even dropping from 4 to 1 is a pretty big change in flow/pressure. An air vent can help if you have any initial squirting or spraying as the air is purged, but i haven't found it necessary with the pressure-compensating emitters. A loop is fine only if it doesn't add significant length of tubing. I have a loop around my pots because it only adds 4' of tubing. For the most part, there's limited benefit to a loop if using pressure-compensating emitters. You can use sturdier stuff like pvc or a heavy duty hose (handle 400ppm and higher, overkill) to bring the water to the irrigation loop. Sounds complicated, but it's really not many parts.. pump, hose, tubing, some shutoff valves, mayb a few "tees", mesh filter on intake hose or pump intake... The rest is for convenience and functionality depending on your preferences... pressure limiter adds convenience... Then any function you want - remote watering? scheduled? etc... Some controllers even have an option for a pump relay switch and solenoid valves. I have some video of my little setup.. i have a controller and solenois valves but they aren't incorporated. can see it in recent diary pictures, but there are videos in week 7 and 12 of the "2026" diaries.. not sure if "2026-1" or "2026-2", but they are only a couple weeks indicating a video is posted, so should be easy to find. picture of rez and pump, video of irrigation and drain pump.
2 likes
Complain
Chucky324
Chucky324answered grow question 2d ago
Hello. Yes... I find the drip emitters didn't allow enough water through. I switched to Raindrip 1/2 circle adjustable stream sprayers, 1/4 circle would work fine too. It allows the water to flow out in a small stream about 2 inches long without the reduced dripping. It's flow adjustable too. I use the plastic holder/stake to push into the clay pellets so the head is just an inch above the clay pellets and spraying down. Works good. Chuck.
1 like
Complain