40x40x120

Matriss
Matrissstarted grow question 12h ago
Hi, I’m thinking of switching to a 40x40x120 cm setup from 60x60x140 for the sake of stealth and discretion. What wattage of light and which strains would you recommend—to get a decent yield? Is 45-50w enough ?
Open
1 like
Answer
UDUDUDUDU
UDUDUDUDUanswered grow question 1d ago
200 lumins minimium
likes
Complain
LPinto
LPintoanswered grow question 1d ago
Boa tarde, eu tentaria colocar uma iluminação mais forte e ajustavel, 100w-120w... assim fica com margem para explorar o espaço ao maximo... mas é possivel com 45-50w
likes
Complain
DutchGlobalCitizen
DutchGlobalCitizenanswered grow question 1d ago
A 40x40 tent is definitely possible, but you're giving up more than 50% of your floor space compared to a 60x60 (0.16 m² vs 0.36 m²). For that size, I'd consider 50W the absolute minimum. Personally, I'd aim for 65-100W of efficient LED lighting so you have some headroom during flower. As for strains, I'd stick with compact genetics or indicas that respond well to training. In a 120 cm tall tent, vertical space becomes a bigger limitation than floor space. You can still pull a respectable harvest from a 40x40, but yield will generally be limited more by canopy size than by genetics. A flat, well-managed canopy will make a bigger difference than chasing a high-yield strain. Hope this helps.
likes
Complain
00110001001001111O
00110001001001111Oanswered grow question 1d ago
going by wattage is imprecise... efficacy varies, so watts equate to different umol/s PAR (PPF). Give a person a fish: 12 hour needs - 150 umol/s PAR output 18 hour needs - 100 umol/s PAR output This will give you ~35-39 DLI in your 0.16m^2 tent. As long as other variables remain the same, it's inversely proportional to hours of operation. More hours requires less umol/s PAR to reach same DLI. Beware, light specifications are often utter bullshit. The estimated watts would be 50-75w and 33-50w, respectively. Entirely depends on true efficacy of the light (umol/J). Also, very, very unlikely you find high efficacy lights in this size. ----------- Teach a person how to fish ------------ 0.16 m^2 area. If you grow autoflowers you can shoot for the 18-hour requirements, but know that the light would be under-powered for a 12-hour needs of a photoperiod. 12 hour needs Sine basics, first... 900ppfd over 12 hours adds up to ~39DLI. This is a specific target, but in reality it's a bit of a grey area.. depends on local variables as far as what a plant can handle per day. This is a good starting point for ambient co2 conditions. It's more likely slightly over what you need than below. That's okay, because we are also calculating based on photon production at the diode which is an over-estimation of what actually hits the plant... regardless, you'll have to observe and adjust light relative to the growth occurring in front of your eyes. There is no "1" answer here... it is relative to several factors - Temp, RH, atmospheric CO2 and whatever else the fuck goes on inside the plant, lol. Take 900 ppfd and multiply by .16m^2... if you know your algebra, you know this essentially converts PPFD to a umol/s PAR measurement for a .16m^2 area, which is 144 umol/s PAR. You need a light that puts out ~150umol/s PAR... Lower wattage lights with this kind of output will produce less heat and last longer while saving some electricty. At this scale, the electricity saved is irrelevant sums.. So, a cheaper light is fine and you may need to replace after ~20-30k hours instead of ~50k.. The most efficacious light might be around 50 watts... i would not expect to find many small lights to meet this standard. ~75 watts of cheap lighting might be a wiser goal.. Again, this depends on efficacy of the light model in question... which is why you should buy based on umol/s PAR output, not wattage. 18 hours -- assume all the caveats above 18 hours is 3/2 more than 12h... we'll use the reciprocol for obvious reason. 2/3rds multiplied by 150 umol/s PAR (from above) is ~100 umol/s PAR For 18h needs, 100umol/s PAR is enough output for ~39 DLI in your tent. ~33 watts minimum with ~3.0 umol/J efficacy, which again, you will be incredibly unlikely at this size of light.. they tend to be cheaper builds. Again, like above, probably wiser to shoot for ~50 watts and expect low efficacy in the 2.0-2.2 umol/J range J/s = w/s, so you can multiple efficacy by watts to calculate umol/s PAR output of the light. This is important to check as it can tell you if the manufacturer is lying about something... or if they list an efficacy that no diode can reach etc etc... lying on grow light specsheets is to be expected, and 10x as likely with cheaper lights.
1 like
Complain
ganjaneer
ganjaneeranswered grow question 1d ago
Hey Matriss, 45 to 50w is enough for a 40x40 if it's a decent led. A good one makes about 2.5 umol/j, so 45w lands around 630 ppfd average over that floor and 50w around 700, inside the 600 to 900 range for veg and flower. a budget light closer to 2.0 umol/j only gets you 500 to 560 at those watts, so in that case I'd look for something around 55 to 65w and dim it as needed. I'm with GoodWeedBerlin that the 120 cm height is the tight part, not the light. Once you take off the pot, the light and a gap above the tops, you're left with roughly 60 cm of plant, so go with an autoflower or a short cultivar and start lst early to keep it low. heat is small at 50w, about 170 btu/h. A little inline fan moving around 55 m3/h of real airflow holds the tent about 3c over the room.
likes
Complain
GoodWeedBerlin
GoodWeedBerlinanswered grow question 1d ago
120 in height is a bit low for a complete grow. I used a 40x40x160 and I was happy about every cm in height. Beside that your plant has to stay really small to fit in between pot and the needed lamp distance to the plant (AKF and ven need space too). Beside that, such a small space might get really warm (lamp). I am recently growing the Triple Mints XXL from Sensi. This is a small plant and stays low (if you train her, she might fit). Whatever strain you choose - it will need a whole lot of training to fit. 45W-50W is enough (even if you might not get the 1000ppfd), I had 75W in my 40x40 but this might be (temperature-wise) to much for 120 height.
likes
Complain