The Grow Awards 2026 🏆
Likes
Comments
Share
Flowering day 37 since time change to 12/12 h. Hey guys :-) The buds have developed incredibly nicely this week. The smell is getting more and more extreme :-) . The whole plant itself looks perfect 👍. The growth has slowly stopped as the full energy goes into the production of the buds. This week it was watered 3 times with 1.2 l each (nutrients see table above) They were individually inspected and checked for their health. Osmosis water for the coming week was refilled in a 100 l tank 👍. Have fun reading the diary and stay healthy 💚🙏🏻 👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼 You can buy this Nutrients at : https://greenbuzzliquids.com/en/shop/ With the discount code: Made_in_Germany you get a discount of 15% on all products from an order value of 100 euros. 👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼 You can buy this strain at : https://www.exoticseed.eu/ Water 💧 💧💧 Osmosis water mixed with normal water (24 hours stale that the chlorine evaporates) to 0.2 EC. Add Cal / Mag to 0.4 Ec Ph with Organic Ph - to 5.8 - 6.5 MadeInGermany
Likes
59
Share
Week 8 Day 49 to harvest P1 harvest was flower day 53 - total wet weight was 24oz and the stem base accounted for 8.0oz, so about 16oz set to dry. I fed P1 half nute flush water again this week. Feed this week was 1.25 gallons 1 time. I used 400ppm Bloom concentrate mix (recipe week 5). However, I also added .5ml/gal of CaliMagic (General Hydroponics 1-0-0) and 7ml of Roots Organics HP2 (Aurora Innovations 0-4-0). PH balance this week was 6.3. And then cut her down 4 days later. P2 harvest was flower day 49 - total wet weight was 16.3oz and the stem base accounted for 6.4oz so about 9.9oz set to dry. (reminder that P2 was the test plant where I broke the main stem and later another later topping from an off branch already topped.) The test resulted in smaller colas in the later topping and the first topping break recovered surprisingly well with colas equal to the biggest. However the later break after the last topping resulted in the smallest cola. This tells me that any damage survived early can see a full recovery but later ones may cost yield. Since P2 looked mostly ready to harvest I decided to dry out after the first feed this week. I will update with cure and smoke details later.
Likes
13
Share
Been 250 watt hps first week turn up to 400 w.
Likes
5
Share
Likes
13
Share
Bestva Quantum Board / Samsung LM301B Mr Hide Seeds Semana de engorde e inicio de lavado de raíces para dos de ellas. De momento todo se ve en orden, buen olor y aspecto pesado. Buenos humos a todos !
Likes
10
Share
18/06: Week 5 – early bloom stage confirmed! 🌱➡️🌸 We're entering week 5 with EC 1.6 and pH 5.8. The very first white pistils have emerged, confirming the transition into early flowering. The recent vertical surge was likely boosted by Far-Red and IR spectrum effects, along with enhanced metabolism from the CO₂ generator. From here, the plants will start shifting energy from stretch to flower production. Environmental control (especially RH and VPD) is now crucial to avoid early bloom issues. LST is being finalized as structure sets in. 21/06: We're now at day 31 since germination, and the flowering phase is clearly underway. Based on the canopy photo, the plants are thriving: a lush, uniform green with no signs of nutrient stress. Buds are starting to stack up nicely, and the foliage remains sturdy and intact. EC has been bumped up to 1.8 this week to support early bloom demands — especially for phosphorus and potassium — and the plants are handling it smoothly. No burnt tips or discoloration, indicating stable nutrient uptake. With environmental parameters dialed in through the GGS controller, everything's in sync. Onward to some serious bud building. 22/06: Stretch is in full swing — the girls are reaching hard, and I’ve had to raise the lights multiple times over the last few days. They’re now hovering just 10 cm above the canopy, delivering 1200 PPFD at 38 °C. We're truly pushing the physiological limit here. Dropping the lights any closer isn’t an option — cooling is maxed out, and more intensity = more heat. The only adjustable variable left would be CO₂ reduction, which I’d rather avoid at this stage. So far, no visible stress signs, but I’m watching them closely. Water uptake is intense — 100L in just 5 days. I refilled today (rather than a full res change) to prevent air pocket formation. Slightly bumped up the EC to temper the stretch. If things keep going vertical, some LST may soon be necessary — a few tops are practically kissing the diodes.
Likes
39
Share
Holy COW some serious growth this week especially out of the Mimosa she is easily 30 inches right now 12 over the Jaeger I'm going to have to figure out a way to even them out I'm thinking BUCKETS
Likes
2
Share
08/26 - Increased water feeds with increased nitrogen - Prepped using clonex mist and clonex gel for cuttings - Pulled 10 clones on the first gen set
Likes
5
Share
@GeMann
Follow
They seem to react in a good way when I water them at PH6.3 just water,a PH of 6.5 at feeding time. Some of the older leaves turned yellow so I did some pruning on them.
Likes
19
Share
@Changman
Follow
The ladies are packing on beautifully and we are now giving them extra strength light during 12:00 till 14:00 slot 100% and lowering the light back down to 75% from 14:00 till 17:00 and then 50% light from 17:00 till 23:00. Lets see what happens
Likes
20
Share
@DrGanj
Follow
Standard week. starting to swell. No issues really. Wish this girl smelled more. My Bakers delight grow has set the bar high and I think this will be just an average pheno. Probably grow this strain from seed again next run unless she gets her dank on. Defoliating heavy around the tops to keep main canopy below strip level. Aim is for even light on every single bud site, or as much as possible
Likes
8
Share
Sunday, May 15. 2022 Plants really looking good and happy to me 😁. The roots are sucking much more water out of the pots than my previous grow and I am giving them a gallon every two days now. They wilted slightly a couple days this week because I didn't realise how much water they were using. Supplemented feed yesterday with Recharge and Cytokin, and foliar spray of same solution this morning. Both plants started showing pistils a couple weeks back but now both are full furred out. Plant #2, the one with whorled phyllotaxy, has red and white pistils; I am not sure of the significance of that, if any.
Likes
135
Share
@FoTwenny
Follow
•••••••••••••••••••••••••• Oct. 24 - Oct. 30 •••••••••••••••••••••••••• 👩‍🌾 SOWED: Aug. 9th 🕛 12/12 START : Oct.1st 🗓️ WEEK 5 of FLOWERING 🏁 ESTIMATED FINISH: Dec. 3rd •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• WEEKLY SUMMARY: •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 🙋‍♀️Fo' Twenny here!🙋‍♀️ Back with this week's update on our mostly Indica 🔵🔵 BLUEBERRY cultivar bred by DUTCH PASSION SEEDS! I am trying a new format for the weekly summary portion of my diary. Let me know what ya'll think! 👃 AROMA: Her aroma is fairly strong for this stage of flower. Blueberry dankness all the way! I look forward to experiencing the evolution of her terpine profile. One of my favorite aspects of growing cannabis is how much these plants change from start to finish and how much variation is possible with this plant. ❇️ BUD STRUCTURE: She is stacking on big round mounds of calyxes and looks like she is going to have large dense buds! 🎨 Color: She is a lighter almost an olive shade of green, right now. Her bright white pistils have a distinctive yellow hue to them. 🌿 STEM, STRETCH, & INTERNODES: She stretched more than I had expected. She has thick stems and relatively tight internodal growth. She definitely looks Indica in her bud structure. ✂️ TRAINING/PRUNING: I have continued selective defoliation as needed to avoid crowding herself and her neighbors. I remove no more than 25% of foliage at any one time, and usually closer 10-15%. I space out defoliation with a minimum of 3 days between sessions, in most instances. There will be exceptions to that, but this is a good rule of thumb I try to adhere to. She has been trained to have 6 main shoots and I am using LST techniques to gently bend her stems to evenly fill her space without overcrowding. ❄️TRICHOMES/RESIN PRODUCTION: Her buds are already starting to sparkle amd glisten. It looks like she will be a good resin producer! 🚿 WATER/FEED: I have continued with a light bidiurnal misting of White Dutch Clover cover crop . This in conjunction with running lower temps (New AC) has seemed to have drastically increased feeding intervals. My plants are needing much less water than in previous runs. I typically give the whole SOG one feed per week with light watering of select individual cultivars as needed between feeds. I try my best to "read" my garden. The amount of water between feeds depends on how soon the next feed will be. I feed the garden as a whole and this run I have been generally spacing feeds out 5-7 days or until the the first plant shows beginning signs of wilt (slight droop of lower fan leaves). 📝 OBSERVATION/NOTES: She doesnt appear to have any signs of deficiency or toxicity. No indications of stress, disease, or pests. Any advice, suggestions, or constructive criticisms are always welcome. Now, for the weekly break down! •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• THIS WEEK'S BREAK DOWN •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 10/29 - Day 81/Day 29 of Bloom °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° 🎥 FILMING DAY 🎥 🚿 FEED DAY 🚿 The cultivar received approximately 1 gallon of solution. I mixed 17 gallons of solution for 17 plants. The solution is applied via wand sprayer powered by a submersible pump attached to a garden hose. Nutrients and additives are added to the reservoir in the order listed below and thoroughly mixed using a large plastic stir spoon. The reservoir is oxygenated by four 4 inch air stones. 👩‍🔬NUTRIENT SOLUTION👩‍🔬 ⬇️Mixing Rundown⬇️ The solution starts with 17 gal tap H2O through two KDF filters mixed in a 36 gallon reservoir. Start pH: 7.8 Start EC: 1.1 TEMP: 74°F 2 tsp/gal - The Guano Company Budswel Liquid 2 tsp/gal - Earth Juice Hi-Brix Molasses 1 tsp/gal - Fox Farm Kelp Me Kelp You pH: 6.0 EC: 1.1 Add 2 tbsp GH pH UP pH: 6.1 3 ml/gal - Plant Revolution Orca .6 ml/gal - Mammoth P .12 tsp/gal - Plant Revolution Great White Premium Mycorrhizae®️ - with Beneficial Bacteria and Trichoderma 1 tsp/gal - Extreme Gardening Mykos WP pH: 6.4 ec: 1.2 Brewed 20 hours pH 7.0 Added 1 tsp/gal of Fox Farm Bembé pH: 6.4 EC: 1.2 •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 10/30 - Day 82/Day 30 of Bloom °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° 📸 PHOTOSHOOT 📸 • My apologies! I only got full garden pictures this week. I have little ones to celebrate Halloween with. I hope y'all enjoy! •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• SUPPLIES & EQUIPMENT CURRENTLY IN USE: •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• • A/C: Whynter ARC-14S 14,000 BTU Dual Hose Portable Air Conditioner • TENT: VIVOSUN 48"x24"x60" Mylar Hydroponic Grow Tent with Observation Window & Floor Tray • POTS: Black 8" tall Active Aqua brand 6" x 6" one gallon square pots/Black 12" tall Active Aqua brand 12" x 12" 3.4 gallon square pots • VEG/AUTOFLOWER INTAKE FAN: None (PASSIVE) VEG/AUTOFLOWER EXHAUST FAN : VIVOSUN 6 Inch 390 CFM Inline Duct Fan with Variable Speed Controller • BLOOM INTAKE FAN: VIVOSUN 6 Inch 390 CFM Inline Duct Fan with Variable Speed Controller • VEG/AUTOFLOWER EXHAUST FAN : VIVOSUN 6 Inch 390 CFM Inline Duct Fan with Variable Speed Controller • BLOOM EXHAUST FAN: AC Infinity CLOUDLINE T8, Quiet 8” Inline Duct Fan with Temperature Humidity Controller - Ventilation Exhaust Fan • VEG/AUTOFLOWER AIR MOVEMENT: 6-Inch Lasko FBA 2004W 2-Speed Clip Fan • BLOOM AIR MOVEMENT: One Honeywell TurboForce Air Circulator Fan Black, HT-900 and Three 6-Inch Lasko FBA 2004W 2-Speed Clip Fans • Bluelab PENPH pH Pen Fully Waterproof Pocket Tester • Bluelab PENCON Conductivity Pen Fully Waterproof Pocket Tester • Kolder Multi-Purpose Liquid and Dry Measuring Cup, 16-Ounce • Fox Farm Measuring Spoons • WATER TREATMENT: Tap H2O run through two AQUACREST Garden Hose Water Filters to remove chlorine and chloramine. – COMING SOON: Hydro-Logic 31023 1000-GPD Evolution RO1000 High Flow RO System, White (HL31023). • WATER APPLICATION: I use 2 different watering systems. The pump sprayer is typically used in early veg, between feeds, or for lighter feeds. Most feeds are usually run through the pump and reservoir because it's faster and easier when dealing with larger volume feeds. – 2 GALLON LAWN & GARDEN PUMP PRESURE SPRAYER. * I removed the spray head due to clogs and it's just faster. – Superior Pump 91250 Utility Pump, 1/4 HP in a heavy duty 27 gallon Tote attatched to a 10 foot garden hose to an Orbit Underground 56246 Green Thumb 9-Pattern Telescoping Wand. – Aeration of the reservoir is accomplished using a General Hydroponics HGC728040 Dual Diaphragm Air Pump 320 GPH 4 Outlet attached with standard aquarium air hose to four 4-Inch Air Stone Disc Bubble Diffusers. • VEG/AUTOFLOWER LIGHTING: 320w MosterBoard V4-PLUS powered by a MEANWELL 320H-48AB DRIVER. There are three V4-PLUS boards prewired and mounted on a 935x195x10mm black heatsink. Dimmer, UV Switch, and IR Switch included. Each board contains two hundred fifty two 3000k lm301h diodes + twelve Osram 660nm diodes plus 4 separately switchable LG UV 395nm diodes and 4 separately switchable Osram IR 730nm diodes. • BLOOM LIGHTING: Two custom mounted lighting units: Each mount has one 480w MEANWELL 480H-48B driver and one 240w MEANWELL 240H-48AB powering 6 KingBright Quantum Boards. Each board contains two hundred fifty two 3500k lm301h diodes + twelve CREE XP-E2 660nm diodes plus four separately switchable CREE XP-E2 730nm diodes and four LG UV 395nm diodes. Hanging between the two mounts are two additional quantum boards with two hundred fifty two 3000k lm301h diodes + twelve 660nm diodes plus four constant power 730nm IR diodes and four 395nm UV diodes. That's a total of 1680 watts of quantum board power in our 96" x 48" bloom tent. ⚠️ ALL DRIVERS MOUNTED REMOTELY IN AN AIR COOLED BOX INSTALLED BETWEEN THE FILTER AND EXHAUST FAN ⚠️ • SLMOTO Universal Oil Drain Pan, 2 Gallon (8 Liter) Capacity ABS Low Profile Oil Drain Pan w/Spout Fit for Motorcycles • Modified Botanicare Low Tide LT Black Tray - 4' x 4' - Modification: Cutaway at corners and used flex-seal tape to create a new edge that will be soft to fit between tent supports. She is supported by 6 Standard Cored Concrete Blocks (Common: 4-in x 8-in x 16-in; Actual: 3.625-in x 7.625-in x 15.625-in). ⚠️THIS TRAY WILL NOT FIT BETWEEN SUPPORTS IN A 48" x 48" or 48" x 96" TENT WITHOUT MAKING MODIFICATIONS TO THE TRAY!⚠️ • Blue Sticky Pads • Yellow Sticky Pads •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• SOIL MIX DETAILS: •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• All components were mixed into a 50 gallon tote that is kept in a warm environment to help innocculate to promote a vast and diverse microbial life in the rhizosphere. Once mixed, add 32-64oz water once every 7-14 days as needed. The goal is to keep the soil moisten without oversaturating. 2 Part - Royal Gold Tupur INGREDIENTS: Coco fiber, aged forest materials, perlite, and basalt 1 Part - Fox Farms Ocean Forest INGREDIENTS: Aged forest products, sphagnum peat moss, earthworm castings, bat guano, fish emulsion, and crab meal. 1 Part - Roots Organics INGREDIENTS: Perlite, Coco Fiber, Peat Moss, Composted Forest Material, Pumice, Worm Castings, Bat Guano, Soybean Meal, Alfalfa Meal, Fishbone Meal, Kelp Meal, and Greensand. Also contains beneficial mycorrhizal fungi: Funneliformis mosseae, Rhizophagus intraradices, Septoglomus desertícola .5 Part - Wiggle Worm Soil Builder Pure Earthworm Castings .5 Part - Ancient Forest Humus .5 Part - Coarse Grade Perlite Inocculated by mixing 1 cup of Extreme Gardening Mycos Watered with pH 6.5 h2O 1 Tsp/gal Real Grower's Recharge 1 tsp/gal Hi-Brix Molasses 2 tsp/gal Fox Farms Kangaroots •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Want to see more cultivars I have growing❓ Please, be sure to check out my other diaries & give me a follow! 👍👍 🙏Thank you for stopping by my garden!🙏 Peace, ☮️✌️ Love, 💚🤟 & Frosty Nugs! ❄️🌲 Happy farmin' friends! ☺️🌱 - Fo' Twenny 👩‍🌾🏻
Likes
11
Share
@Chubbs
Follow
420 Fastbuds BlueDream Auto Week 7 So far so good keeping the same program. Watering 2 liters of straight well water daily as Temps are still in the high 90's so the girls are definitely starting to show that color fade more so now that they're into mid flower. All in all happy Growing
Likes
17
Share
The buds are really starting to form now, I’m getting a lot of purple and some black sugar leaf this is gonna be a wicket show. Oh my freaking sticky icky and I thought growing weed was tricky
Likes
14
Share
Vamos familia tercera semana de floración de estás Tropical Zmoothie de SeedStockers. Que ganas tengo de ver el progreso de esta variedad, las plantas están sanas, se ven con buen color. La cantidad de agua cada 48h entre riegos. Esta semana añadimos nutrientes de la gama Agrobeta. Las plantas están bastante bien ya llevan unas semanas en 12 horas de luz 12 oscuridad. Estas próximas semanas veremos como avanzan. Mars hydro: Code discount: EL420 https://www.mars-hydro.com/ Agrobeta: https://www.agrobeta.com/agrobetatiendaonline/36-abonos-canamo Hasta aquí todo, Buenos humos 💨💨.
Likes
10
Share
@Yolka
Follow
Happy holidays to you guys! 420! That's it, my first grov of photoperiod flowering and on organic substrate without fertilizer has come to an end. Today 4/20/2023 is the last day of light, it'll be in the dark for a while, and April 23 will be harvested. 14 full weeks from seed, 8 weeks of flowering. Looking at the trichomes, I'm worried I'm a little overdoing it on blooming, lots of amber heads on top, the middle and lower ones are milky. One spill this week for 6L with a little drainage and the flower stopped consuming moisture, got a little cooler in the house. Waiting for the harvest :-)