The Grow Awards 2026 🏆
Likes
Comments
Share
Likes
5
Share
@Ninjabuds
Follow
My gorilla cookies from fast buds is really starting to fill in now the buds are getting nice and large. Also the buds have really really pretty tricombs there super white and just pretty. The plant has a super strong smell a carbon filter is a must with this one for sure. Even with one plant it’s to much for my carbon filter you can smell it thru the hz. This plant has a very high potential for making extracts
Likes
18
Share
Just keeps growing. Loving those big developing colas. Waiting on tricomes.
Likes
19
Share
@nonick123
Follow
Día 6 (29/04) Spray solo agua el top del sustrato. DLI 13 Día 7 (30/04) Spray solo agua el top del sustrato. DLI 13 Día 8 (01/05) Spray solo agua el top del sustrato. Subo a DLI 17 Día 9 (02/05) Elimino la cúpula casera de humedad y empiezo a regar con 300 ml solo agua Día 10 (03/05) Empiezo a luchar con una ola de calor inesperada para esta época, que me trae temperaturas exteriores de 30 ºC y humedad relativa del 30%... Mantengo la cúpula casera de humedad Día 11 (04/05) Hace muchísimo calor.. 30 °C. A ver como lo llevan Hago un invento casero para aumentar la humedad Día 12 (05/05) Primera alimentación con Aptus! 300 ml H2O + Regulator 0,15 ml/l + CaMg-Boost 0,25 ml/l + Startbooster 0,25 ml/l - pH 6.2 Creo que las plantas se ven un poco pequeñas para tener 12 días... esperando por explosión de crecimiento en los próximos días.... 💦Nutrients by Aptus Holland - www.aptus-holland.com 🌱Substrate PRO-MIX HP BACILLUS + MYCORRHIZAE - www.pthorticulture.com/en/products/pro-mix-hp-biostimulant-plus-mycorrhizae
Likes
151
Share
@LGreen
Follow
Schönen Sonntag euch 😊 🌿 Wochenupdate Alles läuft weiterhin stabil =) Mein Fokus liegt aktuell auf dem Messen und Erhalten der Nährstofflösung. Bulking hat begonnen und ich freu mich jedes Mal, wenn ich das Zelt aufmachen kann =D Wer den Run hier mitliest, hat mitbekommen, dass ich mich bewusst für einen relativ hohen Start-EC entschieden habe. Das lag zum einen am Bedarf der Genetiken, die sich im Bereich zwischen Middle und Heavy Feed bewegen (wobei der Cross rückblickend nicht so der schlauste Take war 😅). Zum anderen lag es daran, dass ich recht viel Reservoirvolumen habe und möglichst wenige Eingriffe geplant waren =) Ziel war es dabei, jederzeit eine Mindestverfügbarkeit zu gewährleisten. Durch dieses, nennen wir es mal, frühe Gewöhnen – natürlich immer mit Blick auf die Reaktion der Ladies, konnte ich den EC komplett stressfrei bis 2,3 anheben. Danach war für mich Schluss, weil ich ehrlich gesagt keinen Mehrwert darin erkannt habe, sie nicht verheizen wollte und vor allem die Messungen gezeigt haben, dass der selektive Wasserverbrauch zu heftige Maße angenommen hat.. Sprich: Die Lösung selbst konzentriert sich über Zeit zu stark und der EC steigt in zu großen Schritten. Ich habe also damit begonnen, ab diesem Peak-Point den reinen Wasserverbrauch – Achtung, festhalten =DD mit Cal/Mag versetzt wieder aufzufüllen. In den Messungen hat sich dabei ein klares Pattern abgezeichnet 📊 Über 24 Stunden zeigt sich ein leichter Anstieg im EC, bedingt durch primären Wasserverbrauch, bei gleichzeitig sinkendem pH-Wert. Parallel habe ich natürlich immer beobachtet, wie die Ladies auf die Verläufe reagieren =) Sobald ich sehe, dass sich dieses funktionierende Pattern minimal verschiebt, in meinem Fall ein ansteigender EC bei gleichzeitig steigendem pH, refreshe ich 30 Liter der Lösung . Nach dem 30-Liter-Refresh fällt das System wieder in sein vorheriges, stabiles Pattern zurück. Für mich ist das ein klarer Hinweis darauf, dass der Mini-Shift das erste Anzeichen eines beginnenden Ungleichgewichts war =) Ab hier geht’s wieder weiter im Loop 🔄 Ich habe hier echt für mich mitgenommen, dass ein Teil-Refresh ein gutes Diagnose-Werkzeug sein kann. Wenn sich Verläufe nur minimal anders verhalten als gewohnt und man keine klare Ursache validieren kann, kann ein moderater Refresh dabei helfen zu prüfen, ob das System wieder in sein normales Uptake-Pattern zurückfindet. Normalisiert sich das Verhalten danach, kann man unter diesen konstanten Bedingungen davon ausgehen, dass die Ursache in der Lösung lag und nicht bei den Plants oder im Klima 🌸 Pflanzenstatus & Training Endlich ein spannenderer Teil zu berichten =D Das ganze Zelt riecht einfach wie ein Traum, ich würd da am liebsten den ganzen Tag davor sitzen =)) 🌿 Blueberry Cupcake frostet schön weiter ❄️ Bildet aktuell schön homogene Sites und zeigt sich als echt solide Genetik 💪 Sie macht viel mit und lässt sich wirklich gut trainieren. Meine Freundin sagt, die Gute riecht extrem nach Blaubeere – surprise, surprise =D Ich finde eher, sie riecht wie Blaubeerquark? =D Bin wirklich gespannt. Purpz entwickelt sich auch wirklich traumhaft 😊 Schöne kleine Golfbälle, allesamt synchron im Aufbau. Die Trichombildung ist mittlerweile auf Augenhöhe mit BBCC und wirkt nur durch die hellere Pflanzenfarbe selbst weniger spektakulär ✨ Vom Geruch her sehr fruchtig-süßlich, klar in den hellen Noten, aber nicht wirklich definierbar 🍬 Meine Freundin sagt, sie stinkt nach „Gras“ 😂.. Notorious THC frostet aktuell etwas hinterher, was bei den Infos, die ich dazu habe, auch zu erwarten war. Das Blattbild irritiert mich nach wie vor ein wenig, aber da sie sich sichtbar weiterentwickelt und sonst alles sauber läuft, schiebe ich das aktuell auf die Genetik =) Deckt sich auch mit den Infos drüber. Vom Aufbau her ist sie absolut gleichauf mit ihren Schwestern. Sie riecht ziemlich kush-mäßig, musste direkt an so einen dumpfen, aber geilen OG-Smoke denken🔥 =D Meine Freundin wollte ich hiermit nicht belasten – Dessert-Strains only ist hier die Erkenntnis 😄 Guzzlerz kommt auch langsam. Ihre Sites sind recht zart im Vergleich und leider auch deutlich weniger. Sie frostet mittlerweile und ist für ihren Stand synchron gegangen =D ❄️ Ihre Schwestern sind einfach zu dominant – man sieht, das war der schwächste Seed und das zieht sich 😬 Die Ansätze sind trotzdem sehr vielversprechend und in Zukunft gehe ich das auf jeden Fall nochmal an 💚 ⚙️ System Top-Ups erhalten weiterhin die Lösung =) 🔧 1,20 kPa VPD 700–800 ppm CO₂ im Durchschnitt EC 2.000–2.100 µS/cm 1.000 PPFD Danke mal wieder für eure Zeit 😊 Auf ein gutes neues Jahr und feiert schön 🎉🥂
Likes
5
Share
I'm doing an organic soil grow using Purple Cow Organics for the substrate. For germination and seedling phase, I'm using their Seed Starter mix. Once they are ready to focus on vegetative growth, I will transplant them into 5 gallon fabric AutoPots using Purple Cow's Indicanja soil. This is a "water only" soil that I will be attempting to use without feeding much additional nutrients, except for Bloom City Cal-Mag, since I will be using RO water. My tent has CO2 enrichment, so I will be using ~25% higher DLI levels starting at week 2 or 3 than are typical for photoperiod grows. I will adjust as necessary based on how the plants react. #2 and #3 emerged from soil after 2 days (August 22). #1 and 4 took two extra days to be fully emerged with open cotyledons (August 24). During germination, I had VPD set to 0.5 kPa. PPFD was 200 and DLI was around 13, with an 18 hour light cycle. CO2 levels are between 1000-1400 ppm. I included a video showing and explaining my AutoPot and AirDome setup and my general plans for this first grow.
Likes
14
Share
Привет садоводы мой цветок доцветает , еще пару дней и финиш выглядит отлично
Likes
13
Share
@Hawkbo
Follow
Soaked 7.27 for 36ishhrs, into paper towel for 12 hrs then into a solo cup with greentree garden supply pro ultra (coco/perlite). First feed was a diluted leftover feed from my other auto youngins. Basically about 1 ml/g of grow, 7ml/g humid acid, 1ml/g more roots, 1ml/g orca, cannazyme, hydroguard and a sprinkle of living organics in the nutes and on the top of the coco. Usually the ppm will be higher than I want it so I just dilute with r/o water until I'm down to 200-250. It makes it so I cant be accurate on ratios so that's why I'm tellin ya, but it's how I always do it no matter what nutes I use. I started this, a pineapple express and mexican airlines cuz I had 2 slow growers from the first crop I germinated so I just ripped em out and started these in the same cups.
Likes
4
Share
Likes
64
Share
@Roberts
Follow
Baked. Omb auto is doing good this week. Looks like I got past the magnesium issues I was having in prior weeks. She just got some training and us ready for another week. I imagine she will start shifting into flowering very soon. Thank you Bomb seeds. 💣 🤜🏻🤛🏻🌱 Thank you grow diaries community for the 👇likes👇, follows, comments, and subscriptions on my YouTube channel👇. ❄️🌱🍻 Happy Growing 🌱🌱🌱 https://youtube.com/channel/UCAhN7yRzWLpcaRHhMIQ7X4g
Likes
4
Share
Since this is my first time around, before getting started, I took a week to finetune my freshly built setup. Took me a couple of days to get the parameters in order, mostly battling high humidity due to wet soil straight out of the bags. (Plagron Promix) At the beginning of this week i first put the pots in the tent (actually a 4 by 5) and started feeding the soil the myco alraidy. Figured it could be benificial. Them being autoflowers, I planted the seeds in the original pots and covered them with solocups. Watering mostly around the solocups multiple time per day wit a pressure dispenser. I took about 72 hours for the seeds to start germinating. Kept Par levels on the high side (350 and up day by day to 480 in the last days of week 1, probably less to the plants themselves because of the solo cups) thinking the strong genetics could handle it. All the while checking for signs of to much of it. That didn't occur, even after taking of the cups a day or two after germination. Nice as I am, I did not take any pictures, this week! But! some footage from the room where it all happens :)
Likes
Comments
Share
@Growboy89
Follow
Dia Blattläuse sind weg. Ohne etwas dagegen zu machen ausser das Klima im grünen Bereich gehalten. Super 👌 Phosphor und Boost kommt jetzt durchgängig zum Einsatz. Steigend in der Menge. Von 1.5 ml/L auf 3-3.5ml/L gegen Ende des Phosphor Einsatzes. 10 Tage vor Ernte wird gespült. Wann setzt ihr Phosphor ein? Anhand von was macht ihr es Abhängig wann Phosphor zum Einsatz kommt?
Likes
16
Share
@EaRtH
Follow
1.3. - Entering one of the final weeks. Creamatics will be getting pure water from now and Fritters will be feeded at least this week. Buds are looking great, they're smelly and dense 😎 4.3. - Creamatics are almost ready, I will leave them for few more days. Fritters still have one week left at least. Aroma is really strong and I can feel it all over the room. Buds are fat and frosty 🍏 Watered 💧 6.3. - Today was probably last feeding day for Fritters and tomorrow I'm going to harvest the Creamatics as it will be the last day of 10th week. Looking forward to see the results. Watered 💧 7.3. - Week wrap-up: Harvest day for Creamatics! Fritters are still fattening, so I guess they have one more week of flushing left 🍏 1.3. - 7.3. 2024
Processing
Likes
13
Share
Defoliated and fully leaf stripped. I am going all out to see what happens. Wedding gelato is a fairly tall plant for my tent and future grows will have to be properly trained and tied down. Live and learn. So far happy with the results from hydro grow. Roots have worked their way into the res so I have added an air bubbler to the submerged roots.
Likes
13
Share
Everything is going good. Some are showing some sort of deficiency . Lowered lights a little bit. Going to start watering every other day. One of the critical thunder autos is like 8 inches tall lol definitely breeding her.
Likes
7
Share
Likes
13
Share
@MotasKush
Follow
Switching to 12/12 so the girls have the first week of flowering behind them, so far without any major problems, they are out in the world and it is a pleasure to look at them.
Likes
6
Share
@Mraady
Follow
It was my first grow and got 80G dry thanku to everyone who helped me it was outstanding thanks again
Likes
11
Share
@GrowSmith
Follow
Pretty little hairs After adding first dose of PK Warrior all both sides have doubled in size and plant has stretched a little bit more We have to manually adjust the light so that I don’t get any burn Adjusted light from 10 cm to 25 cm