Likes
Comments
Share
Day 92 (34): Increased the size of drainage holes. Drilled right into the container. Damaged some roots for sure. Inflow: EC 1.84 (920 ppm), pH 5.5, 4750 ml Runoff: EC 2.37 (1187 ppm), pH 6.1, 1410 ml (29%) Consumed: 3340 ml (?) ----------------- Day 93 (35): Inflow: EC 1.85 (925 ppm), pH 5.5, 4330 ml Runoff: EC 2.53 (1265 ppm), pH 6.0, 1180 ml (27%) Consumed: 3150 ml ----------------- Day 94 (36): Runoff EC is raising dramatically. +100 ppm a day. Will reduce inflow till 800 ppm for a day or two, and consider flushing if nothing changes. Inflow: EC 1.8 (900 ppm), pH 5.5, 4450 ml Runoff: EC 2.74 (1370 ppm), pH 6.0, 1200 ml (27%) Consumed: 3250 ml ----------------- Day 95 (37): Added 3 ml/l FlashClean into 800 ppm solution, no time to wait for a few days. She’s still alive and progressing. Added more UV lights intervals. From 6x15 min to 9x15 min. Inflow: EC 1.6 (795 ppm), pH 5.5, 4250 ml Runoff: EC 2.52 (1262 ppm), pH 5.9, 1430 ml (34%) Consumed: 2820 ml ----------------- Day 96 (38): Added 2 ml/l FlashClean. Inflow: EC 1.62 (810 ppm), pH 5.5, 4950 ml Runoff: EC 2.54 (1270 ppm), pH 5.9, 1400 ml (28%) Consumed: 3550 ml (?) ----------------- Day 97 (39): Going to switch feeding to Ripen soon. Will keep low ppm for two days. Root check not optimistic. Roots near the drain holes look bound and brown. Hopefully no root rot yet. I will not be able to reach them until harvest. The worms in runoff are definitely root-parasitic. Saw them attacking small pieces of roots. Will keep fertigations with extra runoff as usual, adding even more Hydrogen peroxide. Inflow: EC 1.48 (740 ppm), pH 5.5, 4400 ml Runoff: EC 2.43 (1216 ppm), pH 5.9, 1420 ml (32%) Consumed: 2980 ml -----------------
Likes
Comments
Share
Week 2: The adjustment Hello dear growers and groweresses, it’s time for an update on my grow. My plants have completed the second week and have continued to grow. But they also faced some challenges that I will tell you about. The adjustment My plants have adapted to the new conditions in my room this week. I realized that I had my lamps too close to the plants and that they got too much light and heat. This resulted in them not developing as well as I had hoped. I therefore hung my lamps higher and reduced the intensity of the light. I lowered the PPFD (Photosynthetic Photon Flux Density) from 400 to 280, to give the plants a more comfortable environment. The PPFD is a measure of the amount of light that the plants receive per square meter and second. The higher the PPFD, the more light the plants get, but also the more nutrients and water they need. The plants accepted the change very well and recovered quickly. They started to grow stronger again and formed more leaves. They also got a nicer color and look healthier. One plant that suffered a lot was the Frosty Nightmare. She was overwatered and had trouble developing. She was smaller and weaker than the others and had yellow tips on the leaves. I therefore gave her less water and moved her away from the other plants, to give her more space and air. She recovered and grew again. She is still the smallest of all, but she has potential. I also increased the temperature in my room by 1 degree, to give the plants more heat. I set the temperature from 22 to 23 degrees Celsius, which is still in the optimal range for the plants. The plants liked that and showed me that by their growth. I let them vote democratically, by observing the plants and interpreting their reactions. :D The water filter I also want to introduce you to my water filter from Watertrim, which I use for my grow. It is a great product that saves me a lot of time and money and is also better for the environment. The water filter has only two connections: an inlet and an outlet. So it has no waste water, which would otherwise go into the drain. It has different options of the filter, depending on how much water you want to filter and how high the EC value of the tap water is. The EC value is a measure of the electrical conductivity of the water, which depends on the dissolved minerals. The higher the EC value, the more minerals are in the water, which are not always good for the plants. My filter filters at an inlet EC of 1.0 1000 liters, before it needs to be renewed. Since my tap water has an EC of 0.5, I can filter 2000 liters with it, until I have to renew it. That costs about 100 euros and works easily and quickly via the post. The flow is almost 1 to 1 in speed, so no more waiting. I can tap the water directly from the filter and use it for my grow. I use the filter as follows: I tap water at the filter. I pour normal tap water on it, until I have an EC of 0.3. I add fertilizers etc., depending on what the plants need. I check the EC again and adjust it if necessary. I also adjust the pH value, which should be between 6.2 and 6.5, to ensure optimal nutrient uptake. I give the water to my plants. The water filter is really a great product, even if it is not very cheap in the purchase with once of 240 - 390 euros. But it pays off in the long run, as it saves me a lot of work and costs and also improves the quality of my water. u can find it here : https://watertrim.de The outlook I am very satisfied with the result of the second week. My plants have adapted well and recovered from the problems. They have grown further and formed more leaves. They have recovered well and showed a great growth. I am very excited about the next week, where it goes to the repotting and the ladies can try fertilizer for the first time. I will fertilize this run only a little late, even if I use osmosis water this time. The soil from BioBizz is really great and can carry the first weeks well alone. I look forward to your visits and the next weeks. I will continue to provide you with information and photos and let you participate in my grow. I wish you a nice day and a good grow! 😊
1
Comments
Share
Week 2: The adjustment Hello dear growers and groweresses, it’s time for an update on my grow. My plants have completed the second week and have continued to grow. But they also faced some challenges that I will tell you about. The adjustment My plants have adapted to the new conditions in my room this week. I realized that I had my lamps too close to the plants and that they got too much light and heat. This resulted in them not developing as well as I had hoped. I therefore hung my lamps higher and reduced the intensity of the light. I lowered the PPFD (Photosynthetic Photon Flux Density) from 400 to 280, to give the plants a more comfortable environment. The PPFD is a measure of the amount of light that the plants receive per square meter and second. The higher the PPFD, the more light the plants get, but also the more nutrients and water they need. The plants accepted the change very well and recovered quickly. They started to grow stronger again and formed more leaves. They also got a nicer color and look healthier. One plant that suffered a lot was the Frosty Nightmare. She was overwatered and had trouble developing. She was smaller and weaker than the others and had yellow tips on the leaves. I therefore gave her less water and moved her away from the other plants, to give her more space and air. She recovered and grew again. She is still the smallest of all, but she has potential. I also increased the temperature in my room by 1 degree, to give the plants more heat. I set the temperature from 22 to 23 degrees Celsius, which is still in the optimal range for the plants. The plants liked that and showed me that by their growth. I let them vote democratically, by observing the plants and interpreting their reactions. :D The water filter I also want to introduce you to my water filter from Watertrim, which I use for my grow. It is a great product that saves me a lot of time and money and is also better for the environment. The water filter has only two connections: an inlet and an outlet. So it has no waste water, which would otherwise go into the drain. It has different options of the filter, depending on how much water you want to filter and how high the EC value of the tap water is. The EC value is a measure of the electrical conductivity of the water, which depends on the dissolved minerals. The higher the EC value, the more minerals are in the water, which are not always good for the plants. My filter filters at an inlet EC of 1.0 1000 liters, before it needs to be renewed. Since my tap water has an EC of 0.5, I can filter 2000 liters with it, until I have to renew it. That costs about 100 euros and works easily and quickly via the post. The flow is almost 1 to 1 in speed, so no more waiting. I can tap the water directly from the filter and use it for my grow. I use the filter as follows: I tap water at the filter. I pour normal tap water on it, until I have an EC of 0.3. I add fertilizers etc., depending on what the plants need. I check the EC again and adjust it if necessary. I also adjust the pH value, which should be between 6.2 and 6.5, to ensure optimal nutrient uptake. I give the water to my plants. The water filter is really a great product, even if it is not very cheap in the purchase with once of 240 - 390 euros. But it pays off in the long run, as it saves me a lot of work and costs and also improves the quality of my water. u can find it here : https://watertrim.de The outlook I am very satisfied with the result of the second week. My plants have adapted well and recovered from the problems. They have grown further and formed more leaves. They have recovered well and showed a great growth. I am very excited about the next week, where it goes to the repotting and the ladies can try fertilizer for the first time. I will fertilize this run only a little late, even if I use osmosis water this time. The soil from BioBizz is really great and can carry the first weeks well alone. I look forward to your visits and the next weeks. I will continue to provide you with information and photos and let you participate in my grow. I wish you a nice day and a good grow! 😊
Likes
Comments
Share
@Roberts
Follow
The pure Ice cream clone has been growing nicely and doing her thing. I did move her back to the SE3000 tent. She is steady growing, and likely needs a bigger potter very soon. Everything has been going great. Plus the other clone finally started to grow. It is showing deformities, but it is growing now. Thank you Spider Farmer, and Pure Instinto Seeds. 🤜🏻🤛🏻🌱🌱🌱 Thank you grow diaries community for the 👇likes👇, follows, comments, and subscriptions on my YouTube channel👇. ❄️🌱🍻 Happy Growing 🌱🌱🌱 https://youtube.com/channel/UCAhN7yRzWLpcaRHhMIQ7X4g
2
Comments
Share
Day 29/19 — Began LST on CDLC B; Optimizing light penetration — Environment stable — All plants looking great — Vibe: 😇 Day 30/20 — Topped CDLC B — Plants still praying — Vibe: 🙏 Day 31/21 — SSxDG A/B Topped — Vibe: 😎 Day 32/22 — CDLC A LST on the stems — Environment stable — Cleansed the space with the sound bowl — Vibe: 😇 Day 33/23 — LST on all ladies started today — Added crystals to the soil for each girlie. — Vibe: 👽 Weekly Avg Readings — Lights 24/0 - Level 7 — Temp: 70 (ideal) | 68.9 (avg) — Humidity: 60% | 59.0% — VPD: 1.00 | 0.97 kPa "Perserverance is not a long race; it is many short races one after another." —Walter Elliot
2
Comments
Share
These pics were taken on day of chop 1/8/24. Didn't get any pics of them hanging, will get pics of the trimming process in about a week when she's done drying. I typically dry for around 8-10days with 14 being ultimate goal but I'm fine with 10. Will update in a week or so with the smoke report and final conclusion!
Likes
Comments
Share
@Roberts
Follow
She is a bit stressed. I just changed the solution on her yesterday. She was showing slight deficiency signs. So I just reset the nutrition solution. She bounce out of it soon. I have 2 fruity pebbles plant going in different nutrition. She has done a lot of stretching in last week as well. Thank you Medic Grow, and ILGM. 🤜🏻🤛🏻🌱🌱🌱 Thank you grow diaries community for the 👇likes👇, follows, comments, and subscriptions on my YouTube channel👇. ❄️🌱🍻 Happy Growing https://youtube.com/@mr.sours420growingadventure?si=B9P0WhuqRMB0vbt-
1
Comments
Share
@Roberts
Follow
I just did a solution change. She was put on a less concentrated solution of the Athena nutrition. I think I overdid it last week changing it. She is still making good progress under the Medic Grow Mini Sun-2. Everything is looking good. Thank you Athena, Medic Grow, and ILGM. 🤜🏻🤛🏻🌱🌱🌱 Thank you grow diaries community for the 👇likes👇, follows, comments, and subscriptions on my YouTube channel👇. ❄️🌱🍻 Happy Growing 🌱🌱🌱 https://youtube.com/channel/UCAhN7yRzWLpcaRHhMIQ7X4g
Likes
Comments
Share
Hello this is week 8, week 4 of flower 4-5-6 weeks of flower are the most important because it's bulking phase, i have already see trichomes on sugar leaves are forming, which is a good sign! Wish me luck. Day 51 i did a small defoliation to open up the canopy for better light penetration and airflow
Likes
Comments
Share
Day 79 (1/14) Day 80 (1/15): while I probably could cut these down now, I'm still not seeing a good enough mix of amber yet. Really none other than on the sugar leaves. Left plant is more mature than the plant on the right. I'm going to harvest both at the same time as of now. I want the left plant to be more sleepy time and the right plant to be more daytime smoke. So once the plant on the left is ready, they will both come down.
Likes
Comments
Share
@StarLorr
Follow
Helloing 👋🏻friends and visitors. Welclone to my Clone diary🙃 This is the last FLO weekly update😁 Feeding: Fri 12Jan: 3L each with Flawless Finish pH'd 6.5 ______\_______\______\_____ Trichomes are to my likings and they will not see the sunrise on Jan16th😄 This was a long run. Thanks everyone for the likes and comments for this grow it was really appreciated 👊🏻😃 Keep on growin! Keep on tokin!!! 😙💨💨💨💨💨