buds fatten up now, The hydro plant is destroying the soil completely, the buds are 3x as big lol. i started this grow during the cold winter temperatures, thats why everything got slowed down a few weeks. i expect to harvest withing 2-3weeks from here.

Week 5 At the beginning of the week I set up and tested auto-pot system for 2 plants using the same reservoir of feed water. All connections work fine with no leaks, the floats are free moving and work as intended, I have air pumping into the reservoir and all connections are good there as well. I used black tubing for the feed lines and placed towels over he reservoirs to block out light from the water in the system. After all checks were made, I placed the plants in the pots and turned the system on. At the end of the week I had 3 new nodes of growth since the last topping, so I topped for the third time (4 cuts this week on the 4 set from last week and also removed the lowest). I now have 8 colas set. Feed this week was 400ppm total before add-ins. I used 360ppm Veg concentrate mix (recipe week 2) and 40ppm Bloom concentrate mix (recipe above). However, I also added 1ml/gal of CaliMagic (General Hydroponics 1-0-0) to all feeds and ph balance this week was for 6.3. Next week will consist of training the colas to go where I want them to. I plan to train 6 to the outer ring and 2 to the inner ring. Once I have enough new growth I will set the tomato rings and possibly start wire training. Feed will increase in total ppm and bloom mix and I plan to reduce ph to the 5.8 range slowly, so about 6.1 this week and 5.9 next before flip on week 9.

Esta semana realizamos la tercera y última poda baja. Subimos la potencia de las luminarias Lazerlite Pro 720w by The Pure Factory al 100%. Conectamos a tope la extracción durante el foto periodo nocturno. Y conectamos el aire acondicionado durante el periodo diurno, cortando la extracción. Seguimos con los riegos según la tabla de JUJU Royal by BioBizz.

Week 2 (08.29.2021 - 09.04.2021) Nothing much to report this week. The ladies are looking fantastic. The canopy is from wall-to-wall. The stretch seems to have slowed down quite a bit. However, I've raised my light up as high as it will go with the rope ratchets. If the canopy gets much closer to the light fixture I'm going to have to figure out a way to create some distance. Tying down some branches at this point would be a real pain in the ass, so I'm trying to avoid that. Thank you for stopping by and checking out the progress as we delve deeper into the flowering stage. 2 weeks down, about 7 more to go! See you next week. 🙏

Day 14. Supercropped the top, holding it down with a paperclip. Day 18. Continuing with lst and hst. Happy with the progress. Day 19. Minor defoliation in the morning.

Removed nearly all big fan leafs to get maximum of light penetration to the lower buds and more airflow to prevent mold. Should have weared gloves because it was a sticky mess :D getting more and more smell. I think i will start filling up the bucket only with clear water for one or two more weeks to flush. Think its harvest time soon. Eventually i will swap the whole solution to clear water coming week. ——————— Nahezu alle großen Blätter entfernt, um den unteren buds so viel Licht wie möglich zu geben. Hätte Handschuhe tragen sollen war auf jeden Fall ne klebrige Sauerei :D Stinkt jetzt langsam auch ordentlich die Pflanze. Denke ich werde die nächsten Wochen nur noch mit klarem Wasser ohne Nährstoffe auffüllen um ein bisschen zu spülen. Denke in ein bis zwei Wochen kann geerntet werden. Eventuell tausche ich auch die ganze Nährlösung gegen klares Wasser aus im Laufe der Woche.

Recovery at its finest, that's what you will see on week 4 around here! Guess who's loving the CO2 with high temperature? Thats right, all plants are! The comparison of last week with this week have such a difference, on day 24 I introduced a DIY CO2 bottle, the recipe consist in: -CO2- 2 cups of sugar 1 tablespoon of yeast 1 tablespoon of baking soda 1 later of warm water Mix all ingredients on a bottle, make a nail hole on the cap shake a little (when shaking put your finger on the nail hole, you should hear a hissssss when you release the hole) use it when lights are on, increase temperature to 30-35C, watch for high levels of humidity, and voila! Any other details you want to know ask way :) I haven't started any LST yet, I am waiting for a bit more growth to start bending, I have to make sure all 5 plants will have enough space inside this 2x4 tent. All suggestions are welcomed :) Thats is for now, Stay Lit folks!

Hello growmies 👩‍🌾👨‍🌾🌲🌲, 👋 The girls look really good and force to turn in preflowering, but no! Daddy said, stay in veg 😁 I've already seen pistils since 2 weeks, 💪 continues, defoliation, training. Good responding to training, we can start to guess the canope 😍😋 I need to do big defoliation each week, they are really invasive, Probably turn in flower in 2 weeks. 💧 Give water each 2/3 day And vaporise plant with water + Plagron Roots (1ml/l) 1.5 l Water + Roots + Grow + Zym + Sugar Royal (1 + 5 + 1 + 1 ml/l) PH @6 💡Mars Hydro - FC 3000 30% 42 cm. Mars Hydro Fan kit Setting 4 Have a good week and see you next week 👋 Thanks community for follow, likes, comments, always a pleasure 👩‍🌾👨‍🌾❤️🌲 Mars Hydro - Smart FC3000 300W Samsung LM301B LED Grow Light💡💡 https://www.mars-hydro.com/fc-3000-samsung-lm301b-led-grow-light Mars Hydro - 6 Inch Inline Fan And Carbon Filter Combo With Thermostat Controller 💨💨 https://www.mars-hydro.com/6-inch-inline-duct-fan-and-carbon-filter-combo-with-thermostat-controller Anesia Seeds - High Mars 36% THC🌲🌲 https://anesiaseeds.com/product/high-mars/

Everything's going great. One more week of flushing and I finally get to harvest not experienced at all so I'll be reading up on it alot and any tips would be nice

My little skunk apple runtz lady man I am disappointed so far with this plant not much can be expected from a pollen chuck seed I made myself but I think it will have nice smoke in the end just not alot most likely The day has come and it's time to flip these ladies to flower. I was planning on letting them go untill Friday and let the smaller ones grow just a bit more but they will be fine. I have the eternity cup contest in mind and I'm thinking timing so I need to get these lady done and out my tent lol. This past week I turned the light up alot getting them ready to flower they have grown a bunch inhavendone lst maybe 5 it 6 times on the branchs and they arw nit bendy anymore that will help durring flower.

Day 29 and starting off Week 4 awesome even with my big mistake and not knowing that on mainlining you top first time at third node but the second toppings you can do at first with enough growth but in waited till 3rd on both new mains.. o well you live and learn but hey she looks like shes doing fine atleast will have some nice buds Day 32 update: Now that I have the fungus gnats under control everything has been perfect.. used Foxfarm SledgeHammer to water her to flush all that extra leftover salts in the soil out from the grow nutes, because will be switching to my bloom nutes on next watering, and she seems to have liked it.

Hello. All photos from flower day 6. On flower day 3 I switched the Sanlights up to 80%. On flower day 6 I sprayed the plants with Spruzit, to prevent any kind of insects. As you can see everything is okay besides that algae but nothing too bad so far. All under control. See you next week. ✌️

This is a strain that is very easy to grow and resistant, after the fourth week it sticks a lug, and does not need a lot of vitamins, it grew with only 13 and 12 hours of light and went through cloudy days and a lot of humidity

All good, Flowertime

Last week of veg for this round, next Monday they will start 12/12 in the flower room and get stripped. Watering daily and they are growing fast and looking great, can't wait to see how flower goes for these ladies.

CANADA DAY UPDATE🇨🇦 THE TRAGICALLY HIP🤘🥁🎸🇨🇦 MY SAYING NOW IS: THE ONLY WAY TO GROW IS WITH THE HYDRO🤘 AND REACH FOR THE STARS WITH MARS🤘🤣. So it's been almost a week under the new MARS HYDRO FC4800 and the girls are loving it.. leaves were straight up like they were at a rock concert just blowing in the wind waving their arms like they are in the moshpit🤣🤣 looked so sweet👍. after a day they have stretched so much I had to raise the light already to keep it at 14 inches above the canopy. Plants grow so uniform under these lights, canopy is always nice and even👍. it has a whiter light than the mars tsw2000. Being side by side in my 8x8 tent, I can really see the difference in the color of light. The FC4800 is more of a white light like natural light. I think it might be the blue uv Diodes they added to the fc series lights. I'm amazed at how good this light is already. Barely any heat comes off it. I can rest my hand on it when the dimmer is at 100% and it's just warm. I have it daisy chained to my TSW2000 and it works awesome👍 and I dont have to reach for the other dimmer to do both. One dimmer controls both lights. When I add more lights I will daisy chain them too and control 4 lights from 1 dimmer👍. I still love my tsw2000. It's been going almost non stop since I got it and no issues at all. I take a picture of the Diodes to see if any have burnt out or anything, everything is fine.  same thing with the heat it gives off is just like the FC4800. I can rest my hand on it without burning me👍. Having both lights on 100% because I in flower now, only raises my temperature about 3°celcius. Make sure you got some calmag and if you use reverse osmosis water (bottled water) or filtered water you will want extra calmag because it's filtered out of it👍. These lights are perfect for every stage of growth for germination to flower. Just use the dimmers to reduce the intensity of the lights for whatever stage you are in. Plus they are easy to raise and lower them with the ratchet straps. MARS HYDRO'S recommended height for different stages is pretty accurate but different strains like different Temps and light sensitivity so that's something to look into, a more Mediterranean strain can take more heat and intense lighting. and you can just follow their recommendations for the height for each stage. I slowly turn it up in the later veg cycle until I'm at 75% about a week before I switch to 12/12 and after about 4 or 5 days into flower I'm at 100% with no heat or light stress👍. Mars hydro is awesome for their pricing for what you get👍. They should cost alot more than other brands but shhhhh don't tell them🤣🤣🤣🤣. Just kidding. they want to stay competitive with every brand but there stuff is always cheaper than SF and vipar etc. They know once you use mars hydro products you won't switch to another brand. Why pay more money for something that isn't as good. I've seen lights cheaper than mars but they are cheaper for a reason. They are built cheaper. My TSW2000 is fairly heavy too. But when it comes to getting lights you want some weight to it so you know it's built strong and sturdy and will last a long time.. I called customer service a few times and they will help you out with any questions you may have about the products and they are very well educated in their products👍 very helpful and very friendly. They are awesome 🤜🤛. I can't say enough about this grow tent too. The thing is a beast. I could use the canvas tent to make a trampoline and i doubt it would break its that thick👍 I've had some cheaper tents made of 600d canvas and they aren't that bad. But when you get a tent made from 1680D canvas material it's insane how strong and heavy it is. Before I put the tent together when I lifted the canvas to start wrapping the frame I said to myself.. LORD TUNDERIN JESUS this has some nice weight to it. It was the easiest tent to put together that I've ever had. I went inside with the lights off and got someone to turn it on after a minute or two to look for light leaks and there was none👍. It even blocks out some noise, so if your fans or filters are loud, once it is zipped up it gets quieter. this tent is awesome with So many ports and vents for whatever you need to hook up to it. It has frame bars down the middle and one vertical pole in the middle to keep it sturdy but the poles are made nice and so thick that they probably didn't even need a vertical bar in the middle. It has 2 separate 4x8 floor trays that divide it into 2 4x8 tents. All you need is a mylar divider to easily divide it in half. I love the stickers it comes with. It's nothing big to some people but I know there is lots of people that like them because you see them everywhere in people's tents and in pictures. I love them they are super cool stickers👍. It really locks in the light and temperature and humidity good. Lots of room for all the equipment I have to go in it and will get to put in it. Be good to bring camping too🤣🤣🤣🤜🤛. Thanks for stopping by and taking the time to read this and please leave a comment 🙏🤜🤛 if you have any questions about any of the products I use please feel free to ask me and I can help you out👍🤜🤛 I also know about all their other products too, so any questions about stuff I'm not using I can still help you guys out🤘 and ask about pricing if you're interested in anything and I'll see what kind of deals I can hook you up with. But don't just buy stuff.. let me know so I can talk to my friends at mars hydro and probably get you a better deal👍🤜🤛 https://www.mars-hydro.com Promo code: Rocknroll @marshydropenny Here's some more information about these products I'm using: The goal of MarsHydro is simply to produce the best value grow tents in the  growing field and they didn't disappoint me at all. I'm beyond satisfied with everything. And with the most up to date hydroponic equipment at the lowest prices possible. Their grow tents have combined all their engineers and customers' advice to produce these unbelievable tents.. they really listen to us and change things to our liking so if you own anything from mars just contact them and let them know.. they take our advice and considerations VERY SERIOUSLY so don't hesitate to let them know 💪🤜🤛 The MARS HYDRO 8x8 Grow Tent interior is made of a unique diamond design mylar which is highly reflective. (Other companies mylar and reflective rate is as low as 50%, and it won't provide efficient light. They use thick 1680D oxford canvas, and being double stitched, it is tear proof and perfect for locking in the light. Their grow tent keeps 100% of the light inside the tent and helps your plants absorb more light. EXTRA-THICK material means No light leaks or rips at all.👍 Strong Stable metal corner adapters and poles are the trustful supporters of the tent. It's very sturdy, neither rusting or paint flaking off. quick and easy tool-free setup. They use heavy-duty metal zippers, with double layer black lining, by far the best on the market which creates a light-proof seal. The Easy observation windows are made by double layers of cloth. Observe the growing conditions of your plants without opening the tent and avoid disturbing your plants. The observation windows also serves to dissipate heat and ventilate the air. The tent includes 2 removable waterproof floor trays to hold soil and water. The removable tray can be taken out to wash easily. They guarantee the grow tents are easy to install even if you've never done something like this before. Clear Instructions and no tools needed! They also offer 30-day unconditional refunds for quality problems. Just contact their friendly 24 hours customer service 👍 https://www.mars-hydro.com/ Promo code: rocknroll @marshydropenny GET THE MAX FROM MARS👍: Welcome one of  the newest members of the Mars Hydro family🤜🤛🤘. The Mars Hydro FC 4800 480W LED Grow Light can accommodate up to a 4' x 4' area for flowering. It has OVER 2000 LED chips consisting of the best selling Samsung LM301B diodes which has a Luminous Efficacy of: 220 lm/W 0.2 W, 3 V mid power, Osram 660nm Diodes, Infrared light and UV LIGHT👍. It boasts the incredible efficiency of 2.8 µmol/J, maximum 2.5gram yield per watt with 30% higher Average PPFD. This High-intensity spectrum is beneficial for plants at all stages - from veg to bloom, and creates Big dense Buds👍. achieve 50% higher yields & quality compared with the old lights! Only consumes 480W for 4x4ft personal grows, and 3x3ft for commerical grow. It comes with a dimmer and daisy chain function with a  maximum of up to 15 lights, the master light controls the rest👍. Wide 6-bar design offers even & wide canopy coverage and can maximizes your grow space. slim 180° FOLDABLE DESIGN... YES I SAID FOLDABLE🤘🤣 , making it compact and easy to install, it's IP65 WATERPROOF and will give you no worries while growing in a humid environment and makes it a flexible high performance commercial grow light for enormous  SUPER FROSTY yields.😛😛😛. MARS GETS EM FROSTY BOYS👍 AWESOME HEAT DISSIPATION: The Low energy consumption FC4800 growing light has 6 passive-cooled bars and an aluminum heat-sink a removable driver  you can upgrade later or have it outside your tent. with zero noise  you can save up to 50% in your electricity bill compared to HID's or HPS lights! It also has a removable driver so you can upgrade it in the future or have it outside your grow space for better heat control in your growroom👍 UPGRADED FULL SPECTRUM: Yield Max Spectrum with enhanced red (Top-Bin Samsung 3000k-5000knm, Osram 660nm Deep Red), speed up blooming & fruiting, perfectly suited for full-cycle growing. The FC4800 LED grow lamp was born for Big Buds, perfect for commercial, grow tent, grow room, hydroponics, and all soil grows.👍 THE BEST SAMSUNG DIODES: THE FC4800 has Top Bin genuine Samsung Osram Diodes, combined with remarkable 2.8 µmol/J Efficacy, 30% higher Average PPFD, 50% less energy consumption, to maximize your yields. They give you a TRUSTED 3 years warranty 100% Satisfactory guaranteed!!! https://www.mars-hydro.com         PROMO CODE: rocknroll @marshydropenny Happy growing to all my friends 🤜🤛

Alright growmies 🤙🏻 so week 9 of veg been a lot longer than I expected but due to situations need to be adjusted. So we’re going to repot the runtz into 20litre pots this week and start flowering next week latest. All clones have successfully rooted and will be going into another smaller tent for the time being of flowering the rest. Few absolutely beautiful plants in here so far can’t wait to see what next few weeks look like, hopefully don’t run into hight issues due to stretching 😂👌🏻 well see

Week 11 (26-8 to 1-9) 26-8 Temps: 20 to 23.7 degrees Humidity: 51% to 61% 27-8 Temps: 20.4 to 25.6 degrees Humidity: 45% to 62% Watering: 2000 ml. (Only Calcium) EC: 0.4 PH: 6.1 28-8 Temps: 21.4 to 25.2 degrees Humidity: 54% to 70% 29-8 Temps: 23.2 to 25.6 degrees Humidity: 60% to 72% 30-8 Temps: 19.4 to 24.2 degrees Humidity: 45% to 65% 31-8 Temps: 19.5 to 25.9 degrees Humidity: 46% to 62% 1-9 Temps: 20.8 to 27.1 degrees Humidity: 51% to 66% Watering: 2000 ml. EC: 1.4 PH: 6.1

Hello everyone first grow big bud strain under 600w hps I've noticed that I defo need a humidifier and temp is a little high sometimes reaching 30c and humidity defo to low so humidifier is a must so far they look healthy to me feel free to give me tips or advise thanks