An amazing week 7 is about to start Sunday

Number 1 Number 1 is browning out her hairs and putting on crystal. Seems to be another few weeks to go yet. Number 2 Fall colours, purple, black, brown yellow. A real treat to the eyes. She smells sweet and dripping with resin. No real strong pot smell, and no amber trichomes yet. She is close to getting the axe! The super mutant needs the lumens! Super Mutant This thing is huge. This thing is hungry. This thing is loaded with buds as big as my arms. If every plant was like this, I'd need 1 crop a year. Some of these buds look like they're going to be 2 ozs each! Mammoth monster! Out of these 3 seeds, looks like I got 3 phenos. Although my light is awesome, I think it concentrates blue and red to different areas, making the plants grow at different rates. Number 1 and the super mutant are very similar in structure, except for size. Number 2 was the last to germinate and first to flower. It has a different smell, structure and look. It was from a single promo pack of the NL. The other 2 were from the same package. Will number 2 make it until next week, or will it be a harvest?

4/13 10AM MONDAY They are looking pretty good. Got the ph stabilized and only running 98W! Using a few DROPS in 18oz to test Purpinator on veggies. 4/14 11am Using a little Purpinator .5ml per gallon and will have to do lots of runoff to prevent burns. Using vegetables to test fro Purpinator burns👍 4/15🚨🚨🚨 Your setup photos are great — thanks for sharing them. The R2-D2 power strip topper is a fun touch (he’s guarding the outlet like a proper astromech droid). Here’s a clear breakdown of what I see and my honest opinion on the power draw/safety. What you’re running • Two Mars Hydro TS1000 lights — These are officially rated at 150W each (real-world draw is usually ~145–150W at full power, sometimes a bit less if dimmed). You mentioned ~100W each, but they’re actually higher — so total for the two lights is roughly 300W. • Plus the two black fan speed controllers (one for each tent’s exhaust/inline fan). • A few small wall warts/adapters plugged into the white smart plugs or directly. • You measured 335W total across tents 1 and 2 on one outlet — that lines up reasonably (lights ~300W + fans/controllers ~20–40W depending on speed + minor losses). Is this safe on one standard outlet/circuit? In most US homes a standard wall outlet is on a 15-amp 120V circuit: • Max theoretical capacity = 15A × 120V = 1,800W. • Safe continuous load rule (National Electrical Code for things running 3+ hours, like grow lights): Stay under 80% = 1,440W max. Your 335W total is very low — only about 23% of the safe limit. That’s comfortably safe. No real risk of overheating the outlet, tripping the breaker, or fire hazard from overload right now. My opinion on the setup: • Good: Everything is neatly plugged in. The white smart plugs (with the green lights and blue indicator) and the labeled ones (9e, 10e, 11e) look like you’re using them for timers or monitoring — smart move for controlling lights/fans independently. R2-D2 adds personality and keeps the wall organized. • Fine for now: Two TS1000s + fans on one outlet/circuit is no problem at these low watts. Many small grows run similar loads without issue. • Long-term suggestions (to keep it safe and reliable as your grows expand): ◦ Don’t daisy-chain too much — You already have multiple adapters and controllers stacked. Avoid adding a lot more (e.g., dehumidifier, heater, or more lights) on the same outlet/circuit. ◦ Check heat — Feel the wall outlet and the power strips after the lights have been running for a few hours. They should be only slightly warm, not hot. If anything feels warm/hot, spread the load. ◦ Dedicated circuit is ideal — For peace of mind, run the lights on their own circuit if possible (or at least separate the fans/controllers if you add more equipment later). ◦ Surge protection — Make sure the main power strip or outlet has good surge protection, especially with grow equipment that can have inrush current when turning on. ◦ Monitor actual draw — Your 335W reading is helpful. If you have a kill-a-watt meter or smart plug that shows real-time watts, keep an eye on it when everything is at full power. The houndstooth shirt hanging on tent 2 is a nice personal touch — makes the grow room feel lived-in and less sterile. Quick safety checklist for your whole setup • All cords are in good shape (no fraying, especially the black ones going to the fans). • Nothing is blocking airflow around the plugs/adapters. • The inline fans and ducting look properly attached (important for heat and smell control). • If you ever add more lights or equipment, recalculate the total watts and stay under ~1,200–1,400W on that circuit. Overall, your power setup looks thoughtful and creative (love the R2-D2 detail). It’s not overloaded at 335W, so you’re good to keep running tents 1 and 2 like this while you sterilize and prep tent 3. 4/16 543am 5ft tent sideways attached to 6ft table that can slide around 4/17 3:45am. Here’s the exact vibe you’re going for, and yeah, it’s dark, inappropriate, and could be hilariously unhinged if executed right: Video Concept: “Revenge of the Skid Row Sith” • Split-screen the entire time. • Left side: Clean, epic original Revenge of the Sith footage — Anakin vs. Obi-Wan on Mustafar. Dramatic dialogue, lightsabers humming, lava flows, John Williams score swelling (“Battle of the Heroes” or the full Mustafar duel track). • Right side: Real, raw bodycam or dashcam footage of two absolutely fried-out junkies (or one junkie vs. cops/security) going full delusional meltdown on the street — flailing, screaming nonsense, swinging wildly at nothing or at officers, thinking they’re in an epic lightsaber duel. Twitching, eyes rolled back, yelling shit like “YOU UNDERESTIMATE MY POWER!” while barely able to stand. One of them probably shirtless, covered in sores, pants falling down, yelling about the “high ground” while tripping over a curb. The comedy comes from the perfect sync: • When Anakin says “I hate you!” → Junkie on the right screams “I HATE YOU COPS!!” or just incoherent rage. • When Obi-Wan says “It’s over Anakin, I have the high ground” → The junkie is literally on the curb or a slight incline, yelling at the cop below him “YOU HAVE THE HIGH GROUND?!” • Dramatic slow-mo lightsaber clash → Slow-mo of the junkie wildly swinging a broken bottle or just air, missing by a mile while the cop easily sidesteps. • Anakin getting chopped up and burned → Junkie getting tased or tackled into the dirt, still convulsing and screaming about betrayal. Overlay the full Star Wars audio (dialogue + epic music) on top of the real footage on the right, so the junkies’ actual grunts and screams are mostly drowned out or faintly audible underneath, making it look like they’re perfectly delivering the lines in their drug-fueled psychosis. End it with the classic “You were the chosen one!” speech while the junkie is face-down in his own puke, getting cuffed, still muttering about the dark side. Tone-wise: Super dark humor. It walks the line of “this is fucked up” but the absurdity of the overlay makes it land as comedy instead of just tragedy porn. Think It’s Always Sunny energy meets Cops bloopers with Star Wars fan editing. I can’t actually generate or edit real video clips here (especially not real bodycam footage of people in crisis — that’s a legal/ethical minefield even for parody). But if you want, I could: • Write a full detailed script/timeline with exact timestamps from the Mustafar scene synced to generic “junkie fight” beats. • Suggest public-domain or fair-use-friendly ways to source similar footage without doxxing real people. • Help you describe it precisely enough to feed into a video AI tool like Runway, Kling, Luma, or whatever’s good for video right now (with heavy disclaimers on the dark content). Want me to flesh out the full beat-by-beat script for the Mustafar duel re-cut this way? Or pivot it to fully AI-generated characters (two cartoonish, exaggerated skid-row types in a filthy alley “Mustafar” with lava made of spilled fentanyl and burning trash) to avoid any real-people issues? It’s a nasty, wrong, stupid idea… and that’s exactly why it could be comedy gold in the right hands. Your call how far you want to take it."" 4/18 3:21AM 👨‍🔬🚨"Yeah, pH drift upward overnight (or over several hours) in a freshly mixed hydroponic nutrient batch is super common—especially when you let it sit with constant agitation like a magnetic stirrer. It's not usually a sign that something's broken, but it can make adjustment feel like a battle the next day. Why this happens with your setup CO₂ off-gassing + aeration/agitation: Fresh water (especially tap or even some RO) often holds dissolved CO₂, which forms carbonic acid and keeps pH lower initially. When you mix nutrients and run a magnetic stirrer all night, you're constantly agitating and exposing the solution to air. That drives CO₂ out, reducing the acid, so pH naturally rises (sometimes 0.5–1.5+ points). Magnetic stirrers create good mixing but also promote gas exchange, speeding this up compared to a still jug. Buffering from water and nutrients: Many water sources have alkalinity (bicarbonates, etc.) that acts like a buffer. Nutrients themselves have their own buffering capacity. When you add pH Down right after mixing, the buffers can "fight back" over time, slowly pushing pH higher as the solution stabilizes. General Hydroponics recommends mixing nutrients first, waiting 15–20 minutes (or longer), then adjusting—because immediate readings can be misleading. Temperature and time: pH readings shift with temp, and overnight changes let everything equilibrate. If your stirrer keeps things moving and slightly warmer, that can influence the drift too. Your General Hydroponics pH Down (usually phosphoric acid-based) should still work, but if the solution has strong buffering or you've already hit a stabilized higher pH, it can feel "hard to lower" because you're fighting those buffers. Adding it slowly while stirring, waiting 10–30 minutes between additions, and re-testing helps. Don't chase it too aggressively right after mixing—let the batch settle. Does this happen in the "reservoir" (rez) too? Absolutely—often even more noticeably. In an active rez (with airstones, pumps, or circulation), constant aeration drives the same CO₂ off-gassing, causing pH to creep upward over hours/days. Plant roots taking up nutrients (especially nitrates) can push it higher too. Many growers see this exact pattern: mix and adjust at night, wake up to higher pH. It's why a lot of people premix the night before, let it stabilize with gentle mixing/aeration, then do a final pH check and tweak in the morning before using. Quick tips to make it less frustrating Mixing routine tweak: Use your magnetic stirrer to fully dissolve nutrients, but maybe run it for a few hours instead of all night if the drift is too much. Or mix, stir briefly, let sit still for 30–60+ minutes, test/adjust, then optional light stirring. Water source: If you're on tap/well water with high alkalinity, that amplifies upward drift. RO water often needs more pH adjustment initially but can be more stable once set (though pure RO can sometimes drift differently). Adjustment technique: Add pH Down in small increments while stirring, wait for the meter to stabilize (it can take time), and re-test after 15–30 min. Track how much you use per gallon so you can anticipate next time. Test meter: Make sure it's calibrated and the probe is clean—old or dirty meters give wonky readings that make drift seem worse. If it's stubborn: Some folks add a tiny bit of pH stabilizer or just accept minor daily tweaks. Citric acid-based downs can drift more than phosphoric ones, but GH's is usually pretty reliable. This is one of those classic hydro "annoyances" that almost everyone runs into—your nighttime low-frequency tuning sessions with the subwoofer probably give you plenty of time to notice these little chemistry experiments too.""

We are starting the second week!!! The girls feel good, they are growing like crazy. Tomorrow we will transplant them into larger pots (10 l). I also increase the fertilizer dose to 2 ml/l. Maybe I'll start LST training this week. I still keep the lamps at 30 cm, but I increase the light power to 70%. I'm full of enthusiasm, keep it up! Thank you for all the likes and I wish you successful growth as well. 🙂🙃🙂🙃🙂🙃🙂🙃🙂🙃🙂🙃🙂🙃🙂Hello to all cannabis lovers🤩. The girls have already been transplanted into 10-liter pots. I replanted them yesterday, but I only took photos today. Thanks to valuable advice from @Crashoverite, three days ago I stopped fertilizing and watered the plants with clean water. Thank you very much !!! 🙏🤪😁

The girls are not happy with the temperatures we have here at the moment. It is very hot! Hopefully some extra silicone will help them dealing with the heat. Otherwise both girls look great. The mainlined plant is getting some long colas. She might end up having better yield in the end...

Хороший сорт, приятно пахнет с приятным мягким эффектом. В выращивании очень не любит перепады температур. На тренировки типа LST и Supercropping реагирует положительно!

Today is day 23 of flower. So I've been chasing a minor P-K deficiency. The plants are happy and healthy and are just feeding heavy at the moment. Well over and above any recommended servings with respect to the dry amendments and water soluble P-K inputs. As with any grow regardless of what you're using for inputs (organic amendments/salt based bottle feeding/crop salts/etc....) the recommended feed rates are never anything more than a baseline. So to remedy the deficiency I added the Flower 2 at 1.5 times the reccomended dosage (3 grams per liter of water) and a little over twice the dosage of Gaia Green 2-8-4 Power Bloom dry amendments (250ml per 7 gallon pot). I also fed a mung bean/barley seed sprout tea as well as a compost tea (2/3 of a cup of each seed). The feed rates will stay well above recommended servings for the Flower 2 but the 250ml addition of the 2-8-4 would be considered a large addition for a single serving so I will give the plants 5-7 days to see how they react to dry amendments before top amending again at any rate (you cant burn your plants with organic inputs but you can still suffer nutrient lockout so you need to be mindful and patient when feeding heavy.) On day 19 of flower I did a large pruning/defoliation/lollipopping of the plants. Both from the top of the pot to the bottom of the first layer of trellis removing everything. I also cleaned the plants out from above the first layer of trellis netting to the top of the plant. As I waited to clean up the bottom third of the plants until my typical strip day in flower (day 18-21 depending on strain and flowering times, these are 9 week strains which is why the strip falls in the day 18-21 range, if they were 8 week finishers the leaf strip would take place somewhere between days 14-16). When running multiple layers of trellis netting it's best to prune/lollipop everything below the first layer of netting about 7-10 days before the flip. Odds are your lights wont penetrate that far down the plant so these areas of the plant typically only produce what's commonly known as larf. I'm running new lights so I decided I'd wait until the big strip I always do in flower. This was grower error. I know better and wont make this mistake again. Its unnecessary stress added during flower that could've been prevented. As I decided to wait to clean out the bottoms I didnt prune the plants as aggressively as I normally would (I adopted Grand Master Levels leaf strip practices years ago, check him out on IG or YouTube if you want to see what that looks like). The week went smoothly with no major issues to report. The seasons are changing here so were getting rain, damp wet snow, and have very humid conditions outside. As a result this affects the atmosphere in my grow room but not enough to cause concern. A little less than 6 weeks until the chop!

On day 1 I changed out my reservoir. I lowered my nutes to 650 ppm(25% reduction). I adjusted the PH down to 6.1. My left plant has some burnt tips from either PH shift or over fertilization. My hope is that the lower ppm will help to resolve the issue before it spreads. On day 2 I adjusted the reservoirs PH from 6.3 to 5.9. On day 3 the reservoirs PH is 6.0. I installed my new 200 watt HLG Rspec. I adjusted PPFD readings to 700-1300 PPFD on all tops. On day 4 I adjusted the reservoirs PH from 5.8 to 6.2. On day 5 I adjusted the reservoirs PH from 6.4 to 6.0. I diluted my nutrients in my reservoir by removing one gallon of nutrients from the rez and and adding 2 gallons of straight tap water to the rez. This brought the nute concentration from 770 ppm to 540 ppm as the plants will be entering the ripening stage in a few days and they have too much nitrogen judging by the extremely dark green leaves and burnt leaf tips on some branches of the left side plant. The buds seem slightly smaller then my last run which may be due to an excess of nitrogen and maybe not enough light as some of my tops are taller then the others making proper PPFD challenging. All in all the girls are coming along nice and I look forward to the final weeks of flowering 😀 On day 6 I adjusted the reservoirs PH from 5.9 to 6.2. I think I have halted the nute burn as I haven't seen it progressing any more on the leaves. I will continue to monitor closely during these final weeks. The trichome production is increasing with some trichs on top of colas starting to go cloudy. The pistils are turning brown with roughly 40-50% are turning brown all signs I'm getting closer to the harvest window 😆. I dimmed my light to give 600-1000 PPFD to tops. On day 7 I reduced my temps to 75 during the day and 68 at night. I adjusted the PH of the reservoir from 6.6 to 6.1. My reservoirs ppm was too high so I diluted the rez with 2 gal of tap water. This brought it down to 480ppm. The average ppfd to all 14 tops is 604 with no top receiving more than 1000 ppfd

Calibrated pH meter. Was a little reading high. Started tracking runoff for each plant separately. Mex is very brittle. Broke another branch. Still pretty full. Seem to have the base nutrients dialed in. pH is not longer an issue. Growth is still moderate to slow. Holding off on final topping until nodes grow better. Realized I pruned too high and I lost the node I was going to top for. Plants range from about 6” (bw3) to “10 (mex)

Mi green gelato fue atacada por una plaga de Araña roja, pero he podido combatirla a tiempo. el corte va creciendo bien y ya van saliendo los pistilos.

14-05-2021 (DAY 59) Se realizó el cambio de solución. Las plantas vienen espléndidas y con el Safe roots de Hydrotek ya no tuve mas problemas de raíces. Está entrando la flora mas potente y formándose los Buds.

Vamos familia, actualizamos la cuarta semana de floración de estas Panty Punch de Seedstockers, salieron 3, que van creciendo a buen ritmo aunque marquen una pequeña deficiencia ya estoy solucionandola, veremos cómo progresan. Empezamos añadiendo varios productos de la gama de Agrobeta para la Floración. Temperatura y humedad dentro de los rangos correctos. Vamos viendo cómo avanzan estas próximas semanas. Agrobeta: https://www.agrobeta.com/agrobetatiendaonline/36-abonos-canamo Hasta aquí todo, Buenos humos 💨💨💨

Buds are looking pretty. Already nice frosting of trichomes and density for small size is surprising. Have been worried about my roots and have taken all need steps to try and fix it. So far Daphni shows no signs of stress or nutrient lose. Knock on wood. Will be playing Velvet Underground for her this week. Does it make sense to cut off bad roots?

So frosty wow very nice looking plant so far very dark green and smells very sweet

May 31st - Day 104 : I had to take two babies out because of the lack of space in the tent. Didn’t realize they would grow that much.. So I planted them outside and will let them do their thing as I didn’t have the heart to kill them. But besides that, thriving.

This girl is doing well bushing up nicely after fimming gone a bit pale so hit her with the Shogun nutes now she's settled put a video up of feed one of ec and one of pH when using Shogun i don't do it that often as it's always roughly the same just when n flower I'll switch the calmag and silicon for a pk and a boost max it goes is 2.2 ec her side branches are coming on well hoping the feed sort her colour out other than hat she seems happy not slow drinking well nice chunky stems will get some better pics when possible thanks for reading happy growing guys

- Ich hab die erste Woche des Biobizz Allmix Düngeschemas gestartet und gebe wie immer erstmal vorsichtige 100%, da meine Erde an sich durch den Kompost recht potent sein sollte. - Außerdem hab ich mit meinem Calmag-Rechner mein Leitungswasser angepasst. Die Werte könnt ihr auf den Bildern sehen. - Den PH-Wert passe ich ebenfalls auf 6,5 an.# - Die Lampe bringt zur Zeit etwa einen PPFD-Wert von 350 - 360 µmol/s/m² bei 18 Stunden Beleuchtungszeit (DLI von 22 - 23 mol/d/m²). Sie wird aber nur eingesetzt bis es warm genug draußen bleibt. Tagsüber stehen sie jetzt schon draußen, sofern es nicht regnet oder stürmt. Die Guava macht sich hervorragend und sie ist sehr uniform mit den anderen Fastbuds Strains bis jetzt. Sieht gut aus finde ich 💪😁👍

Turned my lights up to 50% this week continued to lightly defoliate excited to see what comes of this

seeds mafia iz looking good'