Likes
Comments
Share
@Cornfed
Follow
This week I added a new controller to handle up to 8 functions. I installed a new heater, my old humidifier and some LED strips to the controller. Targeting a VPD at 1.0 day and night. Trying to keep the nutrient ppm under 900 and ph at 6.0 in the reservoirs. Ordered a second ph pen because I don’t trust my readings. Will be here by Thursday. Friday: Checked the ppm in the reservoirs and it’s at 1,000. Added more RO water with extra nitrogen to bring the ppm level down to 925. Saturday: I installed an updated AC Infinity controller 69 Pro Plus (controls 8 pieces of equipment) which allowed me to add a humidifier, corner LEDs and a heater to the controller. Overall I’m extremely impressed with this AC Infinity equipment. My VPD is within the range I want to achieve (.8-1.1). I programmed it to maintain 78 degrees and 67% humidity during the day, 73 degrees and 63% humidity at night. Charts posted also show the impact of an open tent compared to the closed environment. The heater is constantly pushing fresh air into the tent, so I don’t need to cycle the exhaust fan often. Rewired the tent again and moved the controller later that night. I mounted the controller on the wall. Added Mars Hydro UV/IR lighting to fill out all 8 slots on the controller. Sunday: I checked the ph in the reservoirs (6.8….i had filled it with 6.0 ph) and the ppm (1200 ppm…I had filled it with 900). So evaporation and possibly a mismeasurement of ph. I topped ff reservoirs with slightly stronger nutes and adjusted ph to 5.8 in the reservoirs. Poor magnesium absorption could be driving some leaf yellowing. Effective tomorrow, I’m switching over to Heads Formula which consistently feeds GH Flora series nutes at Micro (6ml/g), Bloom (9ml/g) and cal mag (3ml/g). Turned on the UV/IR lights for 3 minutes every 8 hours. I’m easing the plants up to 5 minutes every 6 hours which will provide the recommended 20 minutes of IR per day. This will help the plants stretch a little more. Monday: checked ph and ppm in reservoirs. 6.1ph and 880ppm. VPD remains stable except when I open the tent. Tuesday: checked ph (6.4) and ppm (880) in reservoirs. Added .5ml of ph down to two reservoirs. Still see slight yellowing between the veins but it’s not getting worse (might be improving). Adjusting ph down to 6.0 target might have solved this. The plants grew by 1-2” last night…..is the infrared light working already? Decided to mix up fresh nutes for the reservoirs following Heads formula. 6ml Micro and 9ml Bloom per gallon of RO water. Added 5 ml of CalMag too. Ending ppm was 1080 which is too high, so I diluted down to 880 with RO water. 6.0 ph. Wednesday: plants grew another .75 inches last night. I topped above the 5th node. Thursday: added RO water with heavy cal mag to reservoirs to increase amount of CalMag available.
Likes
2
Share
Day 21 I think her extra day in the paper towel germinating while I waited for equipment to arrive, may of sent her straight into flower... shes throwing pistils everywhere. Really jumped in side in 7 days 😂 Lets see how she looks in another 7 days. Turned the auto-pots + air-domes on to get water and oxygen directly to the roots 3 days ago. Feeding Cropsalt at 5.8ph, really enjoying it atm just look at their colour😍
Likes
13
Share
Day 7---Defoliated good bit from all plants removing afflicted leaves, looks to be typical cal/mag deficiency with ph issues. Topped off 2 big plants with ro water, added 6ml micro 6ml bloom and 3ml gro to 2 big plant ppm 900, 2 smaller plant ppm over 1000. Day 6--- Topped off all plants with RO water, added 1ml ph up to plants 1,3,4 to adjust ph. PH of plant 2 more basic than the other 3. Day 5--- Topped off biggest plant 2, added back 10ml cal mag, ppm about 600-700 will check again soon and add back some nutes. Added 1ml ph up to plants 1 and 3 , didn't adjust other two yet. Day 4--- Added 3ml cal mag to all plants as it could be lacking. Added 5ml soul grow and 5ml soul bloom to plant 1 to see something, ppm up to about 1020. Some light defoliation of afflicted leaves on all plants. Day 3---Added 5ml micro and 5ml bloom to plant 2 now at 750ppm. All plants are above 700ppm but below 900ppm. All plants showing signs of something on the leaves but IDK what, manganese? Added 3ml cal mag to biggest plants. Topped off water of 2 biggest plants. Day 2---Checked PH, more minor defoliation of afflicted leaves and to uncover a few more bud sites. Day 1--- Added about 1.5ml ph up since the waters keep going a bit acidic. Some leaves still show some issues but didn't wanna defoliate too much. IDK if it is from PH or over/under feeding plants. Added 2ml cal mag. These plants are continuing to grow and flower, 2 biggest drinking lots of water and making the water more acidic. Topped of water in buckets with RO water. Added 3ml cal mag to all plants Added 5ml micro,bloom, 3ml gro to 2 smallest plants. Added 10ml micro, bloom, 3ml gro to 2 bigger plants. Added .75ml ph up to all plant water to help the PH stay in range. TDS on all are around 800 Light defoliation of all plants to uncover bud sites and remove afflicted leaves.
Likes
8
Share
@Kirsten
Follow
31.12.24: I have been readjusting the LST pegs and wire daily. Sometimes, twice a day! (I know, too much time on my hands)! 😆 The plants have responded fantastically! I'm so glad I gave it a go. Some plants have been a bit too tall, and I snapped Do-sì-dos P3, pulling the stem down. Audibly snapped 😬I let it be, though. It seems to have healed mostly, in only 2 days. I have increased the lighting to 70%. They're getting watered a few times a week, with 1 litre of Dechlorinated water, containing the following nutrients and additives; 1ml of Biobizz Bio-Grow, 1ml Biobizz Top Max, 1ml of Biobizz Bloom, 2ml of cal-mag, 1g of Ecothrive Biosys. The plants are responding well to this concoction, so it's all good so far. The leaves are looking greener and are getting darker. Will be monitoring to continue readjusting the LST ties. Also, to monitor the increased lighting level, to make sure they can handle that yet. 1.1.25: Happy New Year! I have continued to readjust the LST wire and plant pegs. Several times a day. Coincidence would have it, I have a 6ft tropical aquarium which was time for cleaning! I always water my Acer tree in the front yard with this water, with beautiful results 😍 👌 🍁 I decided to try it out in my indoor garden. I'll post photos of before and after to see the difference, good or bad 😅 3.1.25: Plants are doing very well, except for PPP3 I'm quite disappointed in that one, as I feel like it's wasting a space. I guess I'll have to keep it, along with the Do-sì-dos that I snapped twice, which refuses to die 😅 I started to lightly defoliate, which is difficult because I always get carried away with it. I'm going to water again with the nutrients in description of this week. 4.1.25: Continuing to defoliate and adjust the LST pegs and wire. Watered today with 1ltr of dechlorinated water PH'd to 6.0. With the following nutrients;- 2ml Biobizz Bloom, 4ml Biobizz Bio-Grow, 2ml Cal-Mag, 2ml Ecothrive Flourish, 0.2 g/ltr of Ecothrive Biosys. I've increased the Nitrogen by adding double the amount of Biobizz Bio-Grow. I'm trying to keep them growing for as long as possible! I really want to keep the strength up and keep the leaves nice and lush green! 💚 Will update here with more photos and videos. Thanks for checking out my diary 🍃 ✌️
Likes
7
Share
Date: 30.09.2024 So the green gelato is doing fine inside shes kinda starting to turn purplish red on some parts of her buds. The 2 Lemon Cherrys are still outside Im starting to lose hope for the 2 girls but fck it hope will still get smth out. Date: 04.10.2024 Sooo I think that the gelato is going to get chopped down in the next 2-3 weeks. The 2 Lemon Cherrys aint getting any where with the weather atm so I think im just gone give them a few more weeks and hopefully this strain will be good enough for a bit of rosin or IceOLator
Likes
5
Share
The pictures don't do these buds justice. They are a brilliant purple and orange color. I have definitely outdone myself for my first grow ever. These buds have that perfect subtle smell and taste of blue salt water taffy. It's brilliant. I couldn't get it to reveg which is a disappointment but it will live on in my memory
Likes
20
Share
@Chubbs
Follow
420Fastbuds FBT2304 Week 9 Hello everyone from far and wide on this beautiful planet. Weekly update for these twins. Both seem to be in mid flower on cruise control with no big issues present. I'll most likely stop feeding nutes this week and just go with ph'd water after that till harvest. All the colas on both are super chunky so it'll be exciting to see how the next week or two turn out. All in all Happy Growing
Likes
5
Share
🌱 Sour Diesel — Week 8 (Flower Week 3) — Strategic Reset Week ⸻ 🔁 Quick Recap — Where We Are • Genetics: Sour Diesel • Timeline: Week 8 from seed • Flowering: Week 3 • Height: ~60–70 cm (compact structure) • Room Temp: 28°C • RH: 65% • Feed EC: 2.9 • pH: 6.5 (kept above 6.0 intentionally) • Lighting: LED • Action this week: Strategic defoliation This plant is not tall — she’s compact, dense, and structurally tight. Which means airflow and internal light penetration become critical early. And that’s exactly why this week mattered. ⸻ 🍃 The Defoliation — Not Aesthetic. Architectural. This was not cosmetic trimming. It was: • Removing large fan leaves blocking interior bud sites • Cleaning inner congestion • Opening airflow channels • Resetting light distribution across the canopy • Helping the entire room environment (not just this plant) The room needed air — this plant was advanced enough to handle stress. That’s key. Week 3 of flower is the transition window: • Stretch is slowing • Bud sites are set • Energy shifts toward stacking At this stage, a strategic defoliation: • Improves transpiration efficiency • Reduces microclimate humidity pockets • Prevents internal leaf-to-leaf condensation • Encourages bud site activation below the top canopy This was structural architecture. Not haircut vanity. ⸻ 🌡️ 28°C in Flower — “Too Hot?” Let’s Go Deep. People panic when they hear 28°C in flower. But here’s where most growers confuse: 🔥 HPS vs LED Heat Behavior Under HPS: • Radiant heat warms leaf surfaces directly • Leaf temperature often equals or exceeds room temp • 28°C air under HPS can mean 30–32°C leaf temp • That pushes VPD dangerously high Under LED: • Less infrared radiation • Leaf surface temp is typically 1–3°C LOWER than room temp • So at 28°C room temp, leaf temp might be 25–26°C And VPD calculations depend on leaf temperature, not air temperature. ⸻ 🌿 What Is Leaf VPD? VPD (Vapor Pressure Deficit) measures the difference between: • Moisture inside the leaf • Moisture in the surrounding air But if you calculate VPD using only room temp, you’re missing the real transpiration dynamics. With: • 28°C air • ~25–26°C leaf surface (LED) • 65% RH Leaf VPD sits in a very workable mid-flower zone. Not extreme. Not stress-inducing. Not shutdown territory. We’re driving metabolism, not cooking terpenes. ⸻ 💧 Why 65% RH Isn’t Dangerous Here Context matters: • Good airflow • Opened canopy • Compact but cleaned structure • Early-mid flower (Week 3, not Week 7) At this stage: • Pistils are forming • Bud density is still moderate • Transpiration is active High humidity becomes dangerous when: • Bud mass is dense • Internal airflow is poor • Late flower resin traps moisture We’re not there yet. And we just improved airflow with defoliation. ⸻ ⚡ EC 2.9 — Aggressive but Intentional That EC is strong. But: • Plant is compact, not oversized • Sour Diesel can eat • pH 6.5 keeps availability wide (Ca, Mg, P balance) The key will be: • Watching leaf tips • Monitoring runoff behavior • Watching for clawing or salt stress Right now, if she’s praying and stacking, she’s handling it. ⸻ 🔍 What To Expect Next Week (Flower Week 4) After defoliation: You may see: • Slight pause (24–72 hours) • Increased vertical bud push • Better lower-site activation • More defined pistil clustering • Stronger apical dominance response If recovery is clean: • Buds begin early stacking phase • Internodes tighten • Resin production initiates at bract level If stress appears: • Slight leaf droop • Tip burn acceleration • Reduced upward leaf angle But based on structure and timing — this looks calculated, not reactive. ⸻ 🧠 Why This Week Matters Long-Term This week determines: • Airflow pattern for late flower • Mold resistance later • Bud density uniformity • Final trim efficiency • Light-to-bud conversion efficiency This wasn’t about now. This was about Week 7 and 8 survival. ⸻ 🙏 Appreciation Section To: • The OGs here since seed • The new followers discovering the journey • The silent readers • The critics • The skeptics • The lovers • The haters • The platform • The sponsors • The community • Grow Diaries itself Everyone has a place here. Growth happens in public. And that takes courage. Respect to all of you. 📡 Please stay tuned they can try and take us down but we never quit https://www.youtube.com/@DOGDOGTHEDOCTOR NEW 🙏 Thank you for your patience and continued support. FOR DISCOUNT CODES AND MORE JUST FOLLOW THE LINK https://website.beacons.ai/dogdoctorofficial 📲 Don’t forget to Subscribe and follow me on Instagram and YouTube @DogDoctorOfficial for exclusive content, real-time updates, and behind-the-scenes magic. We’ve got so much more coming, including transplanting and all the amazing techniques that go along with it. You won’t want to miss it. GrowDiaries Journal: https://growdiaries.com/grower/dogdoctorofficial Instagram: https://www.instagram.com/dogdoctorofficial/ YouTube: https://www.youtube.com/@dogdoctorofficial Deleted by Youtube Vimeo : https://vimeo.com/dogdoctorofficial Under construction stay tuned ⸻ Explore the Gear that Powers My Grow If you’re curious about the tech I’m using, check out these links: 🔆 Lighting & Environmental Control • Future of Grow — Advanced LED lighting technology https://www.futureofgrow.com/ DISCOUNT CODE: DOG20 • Lumiflora — Under-canopy LED lighting https://lumiflorade.com/ • TrollMaster — Environmental controllers and automation gear (past collaboration) ⸻ Genetics • Zamnesia Seeds — Genetics used in this project https://www.zamnesia.com/ ⸻ 🌱 Soil, Substrates, Boosters & Root Support • Plagron — Substrates, bio mixes, and supportive products https://plagron.com/en/ ⸻ 🎒 Storage, Curing & Preservation • Grove Bags — Curing and storage solutions https://grovebags.com/ ⸻ 📸 Photography Equipment & Tools (Not sponsors, but part of my creative toolkit) • Sony A6700 • Sony full-frame macro lens + few more • Stacking photography workflow - learning • iPhone (for behind-the-scenes shots) We’ve got much more coming as we move through the grow cycles. Trust me, you won’t want to miss the next steps, let’s push the boundaries of indoor horticulture together! As always, this is shared for educational purposes, aiming to spread understanding and appreciation for this plant. Let’s celebrate it responsibly and continue to learn and grow together. With true love comes happiness. Always believe in yourself, and always do things expecting nothing and with an open heart. Be a giver, and the universe will give back in ways you could never imagine. 💚 Growers love to all 💚 📸 P.S. – The Eye Behind the Lens All photos in this diary (for now — except for the ones showing the camera, which I took with an iPhone) are taken with a Sony A6700 paired with a Sony full-frame macro lens and a few more. Photography is part of the story — it’s how we share the fine textures, the glow, and the quiet details that words can’t always capture. I’ve also started experimenting with photo stacking — a technique where multiple images, each taken at a slightly different focus point, are layered together to create one perfectly sharp image from front to back. It’s not digital enhancement or AI; it’s pure photography — a way to reveal the plant’s beauty in microscopic depth, from trichome to petal. You’ll even see a few shots of "ghost me" capturing the shots — camera, lens, setup — because every grow deserves not just to be cultivated, but documented like art. FOR DISCOUNT CODES AND MORE JUST FOLLOW THE LINK https://website.beacons.ai/dogdoctorofficial NEW DISCORD - Official Server Invite Link : https://discord.gg/ksjAkA5T74
Likes
12
Share
Day 15 - The new week meant a change of water, nutrients and an adjustment of lights. Chong is looking like a short, but sturdy little seedling with broad fan leaves and big roots. Max is 10cm vs. Chong at 7cm and her leaves are perky and the stem is thick. They both look good for their own individual reasons. Looking at the roots specifically, Chong seems to be facing similar problems as Cheech in the Cookies Gelato grow - the aeration in the bucket appears to have “dead zones” because of the colour the roots and the manner in which they are sticking together. I’ve adjusted the air stone to be more central in the bucket and cleaned the air tubes because the nutrients stick on the tubes. Other than that, I’ve controlled the PH back down to 6.0 after the addition of the nutrients using the Milwaukee PH controller and decided not to adjust the height of the lights because there was only about 2cm growth this week. Also added the first wire to give Chong a bit of a better bend in her stem, gently starting off the process of LST. Day 20 and the ladies are getting closer to topping. Both are showing clear third nodes with the fourth node opening up. I am sure we will be topping during this next week of veg.
Likes
5
Share
Obvesvacion por Maceta. Maceta 1: Mucha altura y poca expancion laterales, los cobollos se ven con ojitas muy chicas y definidas, no son tan gordos y comprimidos. Satisfecho. 😃 Maceta 2: Creo que tuvo un desarrollo como espere, con cobollos lindos por el medio y una punta imponente, ¿puede que podia ser mejor? no lo se. MUY satisfecho. 😄 Maceta 3: Fue Historia. Maceta 4: Petiza, con su unica punta que es igual al cobollo a mediana altura de la maceta 2, puede que haya sido el sustrato ya que tanto la maceta 3 como esta 4 crecieron de igual manera, poco desarroyo, mismos cuidados que las demas. Por ovias razones la regaba menos ya que no consumia tanto y deje de darle productos ya que no lo veia necesario. Decepcionado. 😑 Ahora voy a Cosechar. 😎
Likes
3
Share
This plant has stayed relatively compact and has developed extremely dense buds. Light is hitting her with around 850 PPFD.
Processing
Likes
14
Share
@Reforced
Follow
Been trying to keep up with pruning, just trimmed all of them up a bit today (12/8) and watered 2 of the master kushs. Looking healthy for the most part.
Likes
52
Share
January 5/2021 Whadddup everyone. A meh week, the one has me feeling down due to its brown/rust leaf.. I don't know whats the issue since the other two are totally fine, everything i've done for them has been the same. Just waiting for time to keep on ticking.. I'm excited to harvest these gals when the time comes.. hopefully just a few more weeks. Getting smelly when the light is off, I can smell it from upstairs which is nice! Kind of skunky but the profile develops every day! Anyways, short and brief as this is just more time out of my day to do the updates.. not sure if im going to keep up with them, but I do like the progress for myself to review. Stay safe and keep it sleeeezy.
Likes
13
Share
Good week. Will be a short fat structure. Should of done more defoliation sooner. Strong smelling. Has more of an indica look .strong thick branches
Likes
3
Share
@sellem
Follow
Welcome to week 2! 17/02 no watering yet. Im content with the grow rate. they also all look healthy and are similiar in speed to each other. Looking forward to whats to come! 19/02 0.7L of 2.5 ml/L Grow and 4 ml/L Rootjuice @1.2 EC 6.0 PH. Should last a while now!
Likes
21
Share
Hey everyone 😃. No training was applied this week. I'll do that in the coming week. It was poured twice with 1 liter this week. The tent was cleaned and the humidifier was refilled every day. The ambient values ​​are in the optimal range and the setup has been checked 👍. I wish you a lot of fun with the update. Stay healthy and let it grow 👍🍀🙏🏻 You can buy this Strain at https://www.amsterdamgenetics.com/product/kosher-tangie-kush/ Type: Kosher Tangie Kush ☝️🏼 Genetics: Kosher Kush X Tangie 👍 Vega lamp: 2 x Todogrow Led Quantum Board 100 W 💡 Bloom Lamp : 2 x Todogrow Led Cxb 3590 COB 3500 K 205W 💡💡☝️🏼 Soil : Canna Coco Professional + ☝️🏼 Fertilizer: Green House Powder Feeding ☝️🏼🌱 Water: Osmosis water mixed with normal water (24 hours stale that the chlorine evaporates) to 0.2 EC. Add Cal / Mag to 0.4 Ec Ph with Organic Ph - to 5.5 - 5.8 .
Likes
10
Share
Great gains this week. Blue dream is coming on strong. A couple of these ladies will be eary finishers. Id guess around 77 days. I never expect any auto to finish before 90 days. Although it does happen. The smell is undeniable. Blue dream is a very distinct terpene profile that cannot be missed! Used recharge on them this week and they early seamed to react well! I'm glad I made that purchase! Looking forward to finishing out this grow! Lollipopped them this week as well.
Likes
111
Share
@DreamIT
Follow
🍋🥧🏎️ LEMON PIE AUTO BY FAST BUDS 🏎️🥧🍋 🍋 12.3 ... 🍋 13.3 I missed a week of update cause damn covid that is slowing down my every project. however the plant takes shape, I hope to be able to constantly resume updates 🍋 14.3 🍋 15.3 🍋 16.3 🍋 17.3 🍋 18.3 ____________________________________________________________________________________ ❌❓Not sure where to buy your seeds? 😮 Fast buds literally ships all over the world, check out their site! http://bit.ly/FastBudsgood __________________________________________________________________________________ 📜 A look at the details of what I'm growing 📜 🍋🥧🏎️Lemon Pie Auto 🏎️🥧🍋 ⚧ Gender ▪️ Feminised ➰ Genes ▪️ 50% Indica / 50% Sativa 🎄 Genetics ▪️ Lemon Pie X Autoflowering Genetics 🚜Harvest ▪️ 450 - 550 g / m² 🌱Vegetation ▪️30 - 35 days 🌷Flowering ▪️ 30-35 days ✨THC ▪️ 24.0% ✅CBD ▪️ 1.0% 🏡Room Type ▪️ Indoor 🌄Room Type ▪️ Outdoor 🕋Room Type ▪️ Greenhouse 🎂Release Year ▪️ 2020 __________________________________________________________________________ 📷🥇 Follow the best photos on Instagram 🥇📷 https://www.instagram.com/dreamit420/ 🔻🔻Leave a comment with your opinions if you pass by here🔻🔻 🤟🤗💚Thanks and Enjoy growth 💚🤗🤟
Likes
59
Share
Getting close to switching her over to flower, she seems to be vegging well, fair few bud sites to watch develop, i also took some AG clones that are looking promising. The strain seems pretty hardy.
Likes
8
Share
@Portnugs
Follow
Resin is increasing and looks like bud sites are ready to start putting on some bulk. Issue with low ph drift reaching 5.2 so I decreased 50ppm with distilled water without calmag to soften the water and counter the drift. After decreasing ppm, ph drift continues, so I flushed for 2 days with distilled water and added back nutrients at half strength to increase to 800 ppm over time.