This week went pretty good! I did some light defoliation, and I also had to tie up some colas for support, as they started drooping towards the floor as the buds begin to bulk up finally. I believe I have another week or two at most for them to bulk, then it will be time to flush. The pictures really do not show how this pig is taking over my little 4x4. I never thought one auto could damn near fill a 4X4, but little miss piggy is trying. The more I feed this hog, the hungrier she gets. I also started feeding her some PK booster last week. I believe my plan to rotate these autos will work out well, as there is absolutely no way I could fit 4 autos in my tent at once nearing the end of flower. I am very excited to see what this lady can do in the next few weeks! Thank you for stopping by, and all the encouragement and support! I appreciate it! Be safe, stay well, and Blaze On!!!

The girls are moving along nicely just watering with water ph to 6.4 this week as I top dressed with Gaia green 4-4-4.Spider farmer Se7000 dialed in at 30 percent and to the ceiling.Noticed some minor deficiencies Day 12 and check soil slurry 50/50 soil/water and the ppm was at 780 lil high at this early stage and the culprit.Going to work on lowering that a bit this week.I did add a top layer of fox farm ocean forest as well which runs a little hot with nutrients rather than the pro mix.I have to remember with these beautiful auto flowers less is better :)

Week 7: The SpiderFarmer SF4000 has arrived. It’s hanging at about 28” at 80% and the plants seem to be very happy. The spectrum is significantly “whiter” rather than the purple of my other lights. Heat is definitely manageable. Buds have chunked up over that last week. I did probably the last feeding as I’m coming up to day 56. Clones are rooted and planted for next round and trying to decide what to run for next round. Some strains are looking better than others but overall pretty nice. Happy Growing 🌱

This one was a fun grow to watch. Lots of main bud stems. Im excited for the next one. Beautiful color. Covered in frost. No pests.

Last day of the fifth week, and these plants are getting an LST treatment on the main stem, under the split. The Ph is looking better, but there are some leaves that are malformed. Probably got too dry?

This week i have lowered wattage of lights by 15-20%. Girls going frosty so quick, started to flushing with flawless finish. I guess we have last 10-12 days depends on specific plants.

Se lograron estabilizar después del transplante, y logran comer bastante, los riegos son cada 2 días, allá purple nos da una distancia internodal mas corta que la 10th, aun así ambas están hermosas

Davvero buono, gusto e sapore unico

I started adding liquid KoolBloom to my reservoir at the start of week 6 after the switch to 12/12. The buds are starting to fill out. Looks like maybe another 2-3 weeks to finish.

The Grapey Walker Kush shot up in week three like crazy. I mean, already looking like bushes. The Super Orange Haze is normal size.

this plant has been stressed a lot since a small one mistake of ph had almost brought to death ... ph4 ... it was left alone with that small root ,,,, I had to transplant and put in a 4 liter pot. ... is reborn but a little smaller and stressed ... has grown and flourished .. but even during this flowering I was not at best with fertilizers .. for 5 weeks of flowering ate only pk 13-14 and candy bud .... then I bought the right thing and began to create a lot of resin on those few glasses present making them a little more fat and tasty

She stretched out a little bit in week five so I upgraded the grow-light to a Mars Hydro TS600. Using 0-10-10 Alaska Morebloom for and Light 5-1-1 fish emulsion.

They are healthy and smelly as usual, very nice recovery from the dry period they've gone trough. 😈

Bonjour à tous les padawans et maîtres jedis Jour98 arrosage avec 2 litres d'eau ph6.3 Jour100 arrosage avec 2 litres d'eau ph6.3 Jour102 arrosage avec 2 litres d'eau ph6.3

FERMAKOR BARREL MIX – BASE IN USE (Testing on the Fantasy Feast girl we pulled out of another diary https://growdiaries.com/diaries/274722-grow-journal-by-yan402 ) (FERMAKOR BASE SYSTEM KOH VERSION diary https://growdiaries.com/diaries/278391-grow-journal-by-yan402) (Urea & Micros on the way — first week running without them) 🍶💧🍶💧🍶💧🍶💧🍶 💧 30 L Barrel – Current Working Mix 🍶💧🍶💧🍶💧🍶💧🍶 Step 1 – Calcium Nitrate (Part A) 7 L warm water (~35–40 °C) → added 45 g Calcinit, stirred until fully clear. That’s the calcium + nitrogen backbone for the feed. Step 2 – FERMAKOR PK Base (Part B) 15 L water in the main barrel → added 30 ml FERMAKOR PK Concentrate, mixed well. This forms the main P + K part of the formula. Step 3 – Combine Solutions Slowly poured the Calcinit mix into the barrel while stirring — no reaction, still crystal clear. That confirms the mix is stable and precipitation-free. 🌿 Step 4 – FPJ / FFJ Batch Added 30 ml homemade FPJ (fish + veg batch) ≈ 1 ml/L. Color shifted to a light-amber tone — looks alive and active. 🍋 Step 5 – Citric Acid Balance Added 1 tsp citric acid after everything was blended to fine-tune pH and help chelate micros later on. 📦 Step 6 – Top Up & Check Filled to the 30 L mark with plain water → pH tested with drops, showing yellow-green — roughly 5.8 – 6.0 range. Nice clean look, stable smell, no residue. 💧 Current Base Ingredients (Active Mix) Warm Water ≈ 22 L total Calcinit 45 g → N + Ca foundation FERMAKOR PK Base 30 ml → P + K support Citric Acid 1 tsp → Chelation + pH balance FPJ / Fish Emulsion 30 ml → Organic enzyme booster Result: clean amber mix, mild and balanced. I’ll let this version run for a week before adding anything. 👀👀👀👀👀👀 Observations and changes 👀👀👀👀👀👀 27.10.25 VW27 noticed some min burnt tips so I decreased Calcium Nitrate 45 to → 40g, decided to add two more elements micros and Epsom salts just to make sure they got everything, Fetrilon Combi 1 (Micros): 0.5 g, Epsom salts: 8 g 28.10.25 VW27 she seems devoid of any deficiencies, seems ready for the flip to 12/12 02.11.25 VW27 girl is looking good so I decided to stop making daily videos and do a standard once a week update. 09.11.25 aVW28 7 days since flip,stretch in full swing, first pistils showing, leaf color deep and healthy. Slight tip burn early week → gone after pH stabilized. Feed stayed clear, no residue, roots clean and sweet-smelling, did what I hope is a last cleanup and pruning🎥 10.11.25 VW29 added Phosphoric acid pH down to the schedule for flowering stage. 14.11.25 FW1 FERMAKOR PK Micros 40 → 50 ml 23.11.25 FW2 got some burnt tips, observe and act accordingly in case it worsens, diluted by 25% for this week. 🌱💦🌱💦🌱💦🌱💦🌱💦🌱 🌿Day to day tasks & actions 🌿 🌱💦🌱💦🌱💦🌱💦🌱💦🌱 23.11.25 FW1 – Fed 3l of #1 → 1l runoff 24.11.25 FW2 – Fed 5l of #1 → 2l runoff 25.11.25 FW2 – Fed 5l of #1 → 2l runoff 26.11.25 FW2 – Fed 5l of #1 → 2l runoff 27.11.25 FW2 – Fed 5l of #1 → 2l runoff 28.11.25 FW2 – Fed 5l of #1 → 2l runoff 29.11.25 FW2 – Fed 5l of #1 → 2l runoff 30.11.25 FW2 – Fed 5l of #1 → 2l runoff 🍶💧🍶💧🍶💧🍶💧🍶 💧 Nutrients in 30 L #1 Veg — FERMAKOR 🍶💧🍶💧🍶💧🍶💧🍶 💧 Calcium Nitrate (Calcinit / Nitcal): 45 g → 40 g → 35 g = 1.33 g/L → 207 ppm N + 253 ppm Ca = 1.17 g/L → 183 ppm N + 224 ppm Ca (current) 💧 PK Concentrate (FERMAKOR Base): 30 ml → 40 ml → 50 ml = 1.00 → 1.33 → 1.66 ml/L → balanced 1:1 P:K + light micros (from extract) 💧 Home-made FFJ/FPJ (Fish + Veg): 30 ml = 1.00 ml/L Epsom Salt (MgSO₄·7H₂O): 8 g = 0.27 g/L → 26 ppm Mg + 35 ppm S 💧 Fetrilon Combi 1 (Micros): 0.5 g = 0.017 g/L → Fe 0.7 ppm • Mn 0.7 ppm • Zn 0.3 ppm • Cu 0.3 ppm • B 0.1 ppm • Mo 0.02 ppm Phosphoric Acid (pH down) + Citric Acid (chelation): → First set pH with phosphoric acid → Add a little citric only if extra chelation is needed 💧 Target pH: 5.8 – 6.0 (drop test yellow-green) 📦 TOTAL Inputs: 60 ml → 70 ml → 80 ml / 48.5 g per 30 L = 2.00 → 2.33 → 2.66 ml/L + 1.62 g/L (current) YouTube Link: https://youtube.com/-m8h?si=A7x4Zlr2kj-_ga31

Week 13 Light cycle=12/12 Light Power=100w Extractor controller settings High temp= 25c Low temp= c Temp step=0c High Rh= 40% Low Rh= % Rh step=0% Speed max=10 Speed min=1 Smart controller settings (during lights on). Lights on=10.01-21.59 Radiator on= below 22.0c Radiator off= above 23.0c Dehumidifier on= not in use Dehumidifier off= not in use Smart controller settings (during lights off). Lights off=22.00-10.00 Radiator on= below 18c Radiator off= above 19c Dehumidifier on= not in use Dehumidifier off= not in use Seperate feeding program. #1 and #2 go onto flawless #3 and #4 stay on schedule. Fri 15/3/24 #3 (Day 85)(Day 47 flower) 📋 Sat 16/3/24 Smart controller settings (during lights on). Lights on=10.01-21.59 Radiator on= below 22.0c Radiator off= above 23.0c Dehumidifier on= above 55% RH Dehumidifier off= below 50% RH or above 24c Smart controller settings (during lights off). Lights off=22.00-10.00 Radiator on= below 18c Radiator off= above 19c Dehumidifier on= not in use Dehumidifier off= not in use #3 (Day 86)(Day 48 flower) 📋 Sun 17/3/24 💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧 Method= automatic Feed=water plants 3&4 Neutralise=0.1ml/L Easy Ph down=0.008ml/L ( 1 drop total) Ec=0.18 PH=6.4/6.5 Time start=12.00pm Finish time=13.45pm (11×5 minute runs with 5 minute gaps) Total flow rate=190ml/min Flow rate per plant=47ml/min. Total volume made=8L Total volume left=2.75L Total volume used=5.25L Volume per plant=2.6L (Est) Runoff. Total runoff=1.75L Ec=1.8 PH=6.3/ 💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧 #3 (Day 87)(Day 49 flower) 📋 Mon 18/3/24 #3 (Day 88)(Day 50 flower) 📋 Tue 19/3/24 #3 (Day 89)(Day 51 flower) 📋 Wed 20/3/24 💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧 Method= automatic Feed=ripen nutes. Dragon Force=4.0ml/L Sumo Boost=1.0ml/L Easy Ph up=0.117ml/L Ec=1.45 PH=6.0/6.2 Time start=12.00pm Finish time=13.45pm (11×5 minute runs with 5 minute gaps) Total flow rate=190ml/min Flow rate per plant=47ml/min. Total volume made=8.5L Total volume left=2.5L Total volume used=6L Volume per plant=3L (Est) Runoff. Total runoff for 2 plants=2L Ec=1.7 PH=6.3/ 💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧 #3 (Day 90)(Day 52 flower) 📋 Ripen Thur 21/3/24 #3 (Day 91)(Day 53 flower) 📋 H=82cm D=20cm DLI=37.0 I'm hoping to make a bit more space for this girl over the next few days. She is probably going to go on for another 2 weeks and hope the extra light will help. Back soon Take it easy.

4/13 10AM MONDAY They are looking pretty good. Got the ph stabilized and only running 98W! Using a few DROPS in 18oz to test Purpinator on veggies. 4/14 11am Using a little Purpinator .5ml per gallon and will have to do lots of runoff to prevent burns. Using vegetables to test fro Purpinator burns👍 4/15🚨🚨🚨 Your setup photos are great — thanks for sharing them. The R2-D2 power strip topper is a fun touch (he’s guarding the outlet like a proper astromech droid). Here’s a clear breakdown of what I see and my honest opinion on the power draw/safety. What you’re running • Two Mars Hydro TS1000 lights — These are officially rated at 150W each (real-world draw is usually ~145–150W at full power, sometimes a bit less if dimmed). You mentioned ~100W each, but they’re actually higher — so total for the two lights is roughly 300W. • Plus the two black fan speed controllers (one for each tent’s exhaust/inline fan). • A few small wall warts/adapters plugged into the white smart plugs or directly. • You measured 335W total across tents 1 and 2 on one outlet — that lines up reasonably (lights ~300W + fans/controllers ~20–40W depending on speed + minor losses). Is this safe on one standard outlet/circuit? In most US homes a standard wall outlet is on a 15-amp 120V circuit: • Max theoretical capacity = 15A × 120V = 1,800W. • Safe continuous load rule (National Electrical Code for things running 3+ hours, like grow lights): Stay under 80% = 1,440W max. Your 335W total is very low — only about 23% of the safe limit. That’s comfortably safe. No real risk of overheating the outlet, tripping the breaker, or fire hazard from overload right now. My opinion on the setup: • Good: Everything is neatly plugged in. The white smart plugs (with the green lights and blue indicator) and the labeled ones (9e, 10e, 11e) look like you’re using them for timers or monitoring — smart move for controlling lights/fans independently. R2-D2 adds personality and keeps the wall organized. • Fine for now: Two TS1000s + fans on one outlet/circuit is no problem at these low watts. Many small grows run similar loads without issue. • Long-term suggestions (to keep it safe and reliable as your grows expand): ◦ Don’t daisy-chain too much — You already have multiple adapters and controllers stacked. Avoid adding a lot more (e.g., dehumidifier, heater, or more lights) on the same outlet/circuit. ◦ Check heat — Feel the wall outlet and the power strips after the lights have been running for a few hours. They should be only slightly warm, not hot. If anything feels warm/hot, spread the load. ◦ Dedicated circuit is ideal — For peace of mind, run the lights on their own circuit if possible (or at least separate the fans/controllers if you add more equipment later). ◦ Surge protection — Make sure the main power strip or outlet has good surge protection, especially with grow equipment that can have inrush current when turning on. ◦ Monitor actual draw — Your 335W reading is helpful. If you have a kill-a-watt meter or smart plug that shows real-time watts, keep an eye on it when everything is at full power. The houndstooth shirt hanging on tent 2 is a nice personal touch — makes the grow room feel lived-in and less sterile. Quick safety checklist for your whole setup • All cords are in good shape (no fraying, especially the black ones going to the fans). • Nothing is blocking airflow around the plugs/adapters. • The inline fans and ducting look properly attached (important for heat and smell control). • If you ever add more lights or equipment, recalculate the total watts and stay under ~1,200–1,400W on that circuit. Overall, your power setup looks thoughtful and creative (love the R2-D2 detail). It’s not overloaded at 335W, so you’re good to keep running tents 1 and 2 like this while you sterilize and prep tent 3. 4/16 543am 5ft tent sideways attached to 6ft table that can slide around

Looks almost ready

WEEK 13 - FLOWERING: Late Flowering Phase ​🌼 FLOWERING PROGRESS The Monster Maker has officially entered Week 9 of flower. The plant is in the middle of a perfect final "fade," with leaves turning deep purple and yellow as she exhausts her internal nutrient stores. Resin production is at its absolute peak—the buds are rock hard and completely over-wintered with milky trichomes. We are seeing the first few amber heads appearing, signaling that harvest is just around the corner. ​👃 TERPENES & AROMA The aroma remains incredibly potent. The dominant scent is a sweet, ripe tangerine, which is layered over a heavy, earthy, and slightly spicy base. It’s a very complex profile that has only become more refined during this final week. ​🌡️ ENVIRONMENT & VPD Conditions are being kept stable for the finish. Current readings show 24.8°C and 46% humidity, which keeps the VPD at a solid 1.65 kPa. This environment ensures the resin stays fresh and the dense buds remain safe from any moisture issues during the final days. ​💧 NUTRIENT FEEDING & WATERING The flush is in full swing! I started using only plain, pH-regulated water on Thursday (2nd April). She is reacting perfectly to the water-only diet, pushing out the last of her resin while cleaning out all residual nutrients for a superior taste and clean burn. ​Current Feeding: Pure Water Only (Flush in progress since April 2nd) ~~ Citric acid (1.2 ml/l) ~~ ​💭 GROWER'S NOTE Week 13 (Flower Week 9). We are watching a masterpiece finish. The trichome coverage is insane, and the fruity-meets-earthy scent is a dream. I am monitoring the amber count daily now. We are looking for that perfect window to chop within the next 7-10 days. The excitement is real!