Na

No Problems Yet, just letting them Grow into the Lights.

Sanlight EVO 3-60 at 80% Day 43: now she's in the tent👌🏻looking good and watered again🌊. Watered with rain water and 1ml/l Powerzyme, 2 ml/l Hesi Boost, 1 ml/l Cal Mag, 1 ml/l Alg a mic, 1 ml/l root Juice, 0.5 ml/l Bloom Complex and 1 ml/l Green Sensation. EC at 1.8 and a pH of 6.4 . Day 45: looking good 🤗 watered with out supplements 👌🏻 Just rain water 👍🏻 Day 46: watered again🌊. Watered with rain water and 1ml/l Powerzyme, 2 ml/l Hesi Boost, 1 ml/l Cal Mag, 1 ml/l Alg a mic, 1 ml/l root Juice, 1.5 ml/l Bloom Complex and 1 ml/l Green Sensation. EC at 1.8 and a pH of 6.4 Day 48: watered with out supplements 👌🏻 Just rain water 👍🏻 Defoliated a little and moved the light farther away 🌞 Looks Like light Stress ( and Bugs ?) 🤬

Sponsored by: 🎭ZAMNESIA SEEDS🎭-💡VIPARSPECTRA💡-💐GREEN BUZZ LIQUIDS💐-🛠️WEDRYER🛠️ 4/9 hello growrez, I'm back with the updates. unfortunately it was another shitty summer and the heat is not over yet, but even if slowly here we are. My bell runtz has stretched out of proportion. the branches I held have stretched a lot and are starting to bloom. today I bathe with fertilizer in the fourth week of flowering __________________________________________ Personal advertising (contains affiliate links) __________________________________________ 🦄Zamnesia boasts the most complete and accurate site where you can find everything related to cannabis and the "psychedelic" world. Autoflowering, feminized seeds, mushrooms, salvia divinorum, afrodisiacim of everything, and more! ( no affiliate link) ✅https://bit.ly/Zamnesiaseeds __________________________________________ Did you know that Green Buzz Liquids fertilizers are 100% vegan? A complete line of products ready to give the best to each of your plants! Visit the site and see my journals to see how they work 🦄 🤯 And with the code "dreami t" you will immediately receive a 15% discount on your purchases ✅https: //bit.ly/GreenBuzzLiquidsPro __________________________________________ 👀 Are you looking for a good lamp to start with? 👀 🌞Viparspectra has something more than the others, take a look at their site. ⏩ Use "GDVIP" for an extra discount or "DREAMIT3" for an extra 5 %% discount 👀 Search for it on Amazon ✅Amazon USA: https://amzn.to/30xSTVq ✅Amazon Canada: https://amzn.to/38udUVe ✅Viparspectra UE: bit.ly/ViparspectraUE ✅Viparspectra USA: bit.ly/ViparspectraUS ______________________________________________ 🌈 Tired of blowing on your weed hoping it dries quickly? Check out the Wedryer website! You will find a well-made accessory that will help your weed dry in just 8-10 days without the annoying risk of finding mold or other annoyances! (no affiliate links) ✅https: //bit.ly/Wedryer_ ______________________________________________ 📷🥇Follow the best photos on Instagram 🥇📷 https://www.instagram.com/dreamit420/ Backup https://www.instagram.com/dreamit4200/ 🔻🔻Leave a comment with your opinion if you pass by here🔻🔻 🤟🦄💚 Thank you and good growth 💚🦄🤟

So really weird , I just 2 different phen types of orange bud... because one of them is growing very very purple buds. Or ILGM sent a wrong seed..lol.. either way it's really pretty..😍 they both have a similar smell to them , very citrusy smell. Also they are thriving on the new nutrients Advanced Sensi products are amazing... I will never use Lotus ever again.

1 gallon, of the above listed nutrients, every 3 days, for the past 2 weeks! I've been selectively de-leafing every about 5-7 days.. I haven't needed to remove much at all, to maintain good light coverage to bud-sites!

10/26: All but one are flowering now, and most are stretching. There are a few shorter ones, thankfully, so they'll get moved up to the top of the closet in another day or two and I'll have a little more room for the big girls to spread out a little bit. 10/27: I rearranged the garden a little bit today and checked whether they needed water or not. I foliar fed with Big Bloom and a little Tiger Bloom today. I'm seeing signs of potassium deficiency on several of them. 10/28: I watered everybody with about 1/4 gallon and included a little terpinator, cal-mag, bembe, and beastie bloomz. I uploaded a couple of photos showing some weird curling of the newest growth...just an odd varietal trait I think because I've seen it before on my Candy Cane F2's. 10/29: I rotated everybody on the edges and plucked some older, lower leaves. They are damn near totally dry, so flushing tomorrow. 10/30: I decided not to flush based partly on how shitty the weather is right now...and partly because I'm seeing some N deficiency signs in several plants and really can't afford to put off feeding them again until they dry after a 3-gallon flush. So, instead, I thoroughly watered everybody with about 3/4 gallon including cal-mag, myco/tricho, beneficial bacteria, humic acid, bembe, and terpinator. I let them sit in their catchment trays long enough to soak all the run-off back up, so they are fairly well saturated now with things that should make the roots really happy. I've added another oscillating fan and got the hygrostat set to kick on the exhaust whenever the humidity reaches 55%, so it's pretty much staying on right now. Hopefully they are dried back out by Friday so I can give them a last good dose of N to help with their stretch. I'll also start going heavy with P and K, and increase terpenoid and flavonoid enhancers. I'm gonna give Signal by True a try when I finish my current bottle of Terpinator. I just can't bring myself to keep paying over $60/gallon when I can get a gallon of Signal for under $40. While watering today, I emptied the closet completely and had plants all over the place...my cats were in heaven..stalking each other under the jungle canopy.😺 It really does amaze me that I'm fitting all these plants into such a small space..😳 10/31: I rotated the edge plants and checked their moisture level. I'll feed them tomorrow. 11/1: I took everybody out of the closet and did a little defoliating. I fed everybody with about a half-gallon including all the good stuff.

Aplicamos recientemente jabón potásico por problemas con trips... estamos controlando todo a tiempo, en 3 semanas ya pasaremos al armario grande para continuar dándole crescimiento para las nenas farmers!🍁

It’s warming up outside so the a/c and dehumidifier are working a bit. Got the lights on during the night so just a few hours at lights on they work a bit hard. Cleaned up underneath removing any sucker shoots and leaf that was near the soil. Not much really. Mostly on #3 as I didn’t train out the branches as much and she grew tighter together, so I removed mostly all inner growth blocking light and that allowed a lot more penetration and flow. Left a few leaves below to die off naturally…more the better. Gonna put some Grub Grenades in the pots with some yellow sticky cards. Not because I see anything, just being cautious. I do see what looks like Springtails but don’t seem to be an issue yet. Still looking green and healthy so I’m happy! Grow on! Update Made a few adjustments. I let the tops grow into the tsw2000, 18” to tops. I didn’t like how they looked so I raised it back to 24” where I’ll keep it. The “Kind LED” I know from previous grows that it can’t get closer then 24”. But this is my first run with “Mars” so I’m still figuring out the distance for my setup with additional overlapping light intensity from other lights. With that being said another pod failed so I’m down 2-Kind LED’s now. Gonna remove all old tech and use all newer TS series lighting. All Mars moving forward. Seems to be a great light and when compared to other quality lights you can’t beat the price!

What up Fam. These girls are growing amazing. Now that I can control the temps a little better they've taken off with growth. Starting the flower period which we all no know what that means. The countdown is on. Over all Happy Growing.

These are 4 clones off of the mother plant. They vegged for 9 weeks.

She has a delicious candy/sweet perfume! Bud structure is really nice, tight nodes and dense buds, I love this {unknown} strain! 😍

I may not be great with the camera and media, but this was a fun run for me. Just as fun as watching everyone's approach and finishing results. Huge thanks to our sponsors. 1 plant to rule them all 😆🙄😂 Stay lit my friends... won't be long now!

Day 65 : officially 1st day of flush . Changed the reservoir with fresh water and 1.2g/5 gallons of Yucca extract and 5ml/gallon of Cleanex from Botanicare . Day 68- I did some defoliate. Few more days until harvest.

All girls were 6-7 nodes high I clipped them at the nearest nodes that were close together and healthiest. I’ve heard it’s all ab the fee and I felt like that was the best choice! I’m super excited to be doing this and I’ll be doing them both differently strain specific. Glad to have the tent up and running again it was nice to take a week off during the holiday season. Can’t wait to get these girls off to a great start only thing I wasn’t excited ab was the fact I know they came from a tent that had a small infestation so I’ll be treating them as soon as they bounce back for preventative measures for a few weeks. Once again super excited and a good trial run before I get some seeds in the soil since these are clones once again. Happy growing y’all and I’ll take more pics here in the next few days to see how they react to the major haircut. Update: All reacting very well to topping! First time doing this so very exciting!!! The dosi I’d have to say is reacting better than the Maui which I thought was going to be the other way around since it’s sativa vs indica. I’ll be doing nebula and nugbucket mailing/manifold of each strain and recording everything pretty well. I’m more excited about getting this spider farm 2000 light instead of using the bestva 1000 either way it’s going to produce more and I like the white light instead of the blurple. Super excited ab this run!!!!

WEEK 5 SETUP - ROOT ZONES Optimizing cannabis performance requires balancing a strict temperature gradient between a cool root zone (68°F–72°F) to maximize dissolved oxygen and active nutrient transport, and a warm canopy (77°F–95°F) to accelerate photosynthetic enzyme activity and electron transport rates. There is a critical anatomical temperature gradient required for optimal cannabis metabolism: The Root Zone (68°F–72°F): Must be kept cool to maximize dissolved oxygen, preventing root rot (Pythium) and ensuring active transport ATP powers root elongation. The Metabolic Sweet Spot (77°F–95°F): The primary Electron Transport Chain (ETC) enzymes and ATP synthase complexes in the foliage require these warmer temperatures to maximize molecular collisions, accelerating respiration and carbon fixation. The Destruction Threshold (104°F): Enzymes and lipid membranes denature, causing structural metabolic collapse. Active transpiration constantly pulls dissolved O2 down through the top of the substrate like a piston. At night, the top-down pump completely stops. When transpiration shuts down after dark, the root zone can quickly become stagnant and oxygen-depleted because the mechanical "pump" is off, while the roots still need to breathe. Having a hole in the middle of the 100 gallon, in which all the air intake in an indoor grow tent comes up through the middle of the pot rather than open side panels, and having tent exhaust connected to RH allows cellular respiration to enact the exhaust, which creates a negative pressure differential that will act as a pump at night similar to daytime, but with a different mechanism. By routing your intake exclusively through a central hole in the pot and linking the exhaust to a Relative Humidity (RH) controller, you are effectively replacing the daytime transpiration-driven pull with a nighttime vapor-driven physical pull. Because the side intake vents are sealed, the tent is forced to draw its replacement air directly up through the center of your massive pot. This actively pulls stagnant, CO2-heavy air out of the root zone and replaces it with fresh, oxygenated room air. UVC 264nm duct sealed with HEPA filters to prevent contamination of pathogens. Constant airflow of 0.2m/s underside of the elevated pot to prevent potential runoff stagnation. Polystyrene insulation to prevent core desiccation, HVAC climate-matched intake, inline UVC/HEPA filtration, and constant underside air velocity are successfully engineered around every major failure point. Because cellular respiration spikes RH in waves, ensure your exhaust controller has a tight deadband (e.g., +/- 2-4% RH). This prevents the fan from "hunting" (short-cycling on and off too rapidly), which would cause erratic pressure shifts in the root zone. Using large-sized Hydroton (expanded clay) pebbles fill a 12-to-14-inch diameter middle cavity in the pot solves the air channeling problem entirely. By replacing a dense substrate core with a highly porous, structural aggregate, it creates a dedicated internal air plenum. This ensures that the negative pressure differential acts uniformly across the entire vertical column of the root zone. Often referred to as a sub-surface aeration plenum or negative-pressure root system. By using negative pressure to pull or push conditioned air through a Hydroton (expanded clay pebble) plenum, this setup optimizes the root zone microclimate while preventing the typical gas stratification found in traditional containers. The 12-to-14-inch Hydroton layer acts as a high-porosity distribution vault. Because Hydroton has massive interstitial spacing, air can move through it with minimal resistance before diffusing into the denser substrate above. Instead of air channeling up a single path, the system forces the conditioned air to spread outward and upward evenly across the entire radius of the root mass. Roots actively consume Oxygen and respire Carbon Dioxide (CO₂). In standard pots, heavy CO₂ and excess Nitrogen can settle at the bottom, creating an anaerobic "dead zone." This negative pressure actively pulls those heavy gases out, replacing them with oxygen-rich, HVAC-conditioned air. Roots that penetrate the polystyrene/mesh barrier into the Hydroton core will experience incredible growth due to the hyper-oxygenated environment. However, because of the high nighttime airflow, the surfaces of the Hydroton will dry rapidly after irrigation. This will create a localized, self-regulating air-pruning zone, forcing the plant to explode with dense, lateral feeder-root branching just outside the core. Turns one's massive pot into a bi-directional, lung-like matrix. Equipped to destroy all limits set before it with nearly zero points of failure. With these safeguards implemented, the root zone environment achieves an unprecedented level of equilibrium. The plant drives the system. High transpiration creates a powerful top-down pull, dragging oxygenated moisture through the upper profile. The HVAC and HEPA/UVC intake runs passively or under low static pressure to maintain ideal ambient baselines. Transpiration ceases(Photosynthesis), and metabolic cellular respiration triggers a spike in relative humidity. The RH controller instantly fires the exhaust fan. The negative pressure vacuum instantly engages the clean, conditioned cohesive air column. Fresh air sweeps through the sealed duct on the underside of the buffer zone(pot), enters the 12-to-14-inch Hydroton plenum, and diffuses radially outward through the HVAC-controlled substrate. Stagnant CO₂ and nitrogen are actively evacuated. This setup prevents root rot, boosts oxygen levels at the root zone, and accelerates plant growth by ensuring the root system always breathes fresh air. Polystyrene keeps the core from drying out prematurely, the physical barrier keeps the media from migrating into the plenum, and the climate-controlled intake ensures the root zone never drops below its metabolic sweet spot. In standard growing systems, a root zone of this massive scale always runs into a diminishing return curve: the larger the pot, the easier it is to create cold, stagnant, anaerobic dead zones in the deep interior. This design completely smashes that ceiling. By turning the absolute center of the mass into the cleanest, highest-flowing, most oxygen-rich zone in the entire garden, it allows the root system to expand exponentially without ever hitting a wall. One is giving the plant the ultimate foundation to maximize its genetic potential, pushing growth rates, nutrient uptake, and overall vitality to their absolute limits. Also allows intake while catching all CO2 generation in the bottom half of the tent, kicking it up into the canopy every morning, even all around with 360 distribution, zero dead spots. Sub-surface aeration and magneto-electroculture matrix: a highly sophisticated, closed-loop engineering framework that perfectly bridges plant physiology with fluid dynamics and electromagnetic physics. By turning a traditional container into a bi-directional pneumatic lung, the design successfully bypasses the biological stagnation limits of massive root zones while leveraging micro-Lorentz forces to enhance nutrient mobility. Integrating a massive copper rod with an iron core (an electromagnet core) directly down the central axis of the Hydroton plenum—and driving a magnetoelectric field at the base using a neodymium magnet—shifts setup from a basic galvanic circuit to a specialized magneto-electroculture matrix. Running the earth battery's DC current through a highly conductive copper casing insulated around a ferromagnetic iron core transforms the central air column into an inductive broadcast tower for the rhizosphere. Just big enough to fill the massive root zones but not enough to leave the 4x4 tent. The physics and structural safety of this addition alter the system's dynamics in a couple of ways. Copper is an excellent electrical conductor but is non-magnetic. By wrapping the high-permeability iron core inside that copper column, you focus and amplify any magnetic flux lines generated by the circulating micro-currents. ⚠️ Extreme Handling Hazards ⚠️ 38 mm OD x 19 mm ID x 6 mm N52. ⚠️ Extreme Handling Hazards ⚠️ ⚠️Keep it well away from pacemakers, credit cards, mechanical watches, and sensitive magnetic sensors.⚠️ There is a permanent neodymium magnet at the base of this core, inducing an electrical current; this creates a localized electromagnetic actuator. Because it sits at the bottom of the plenum (where HEPA/UVC filtered intake air enters), the air moving up the column passes through a dense, structured magnetic gradient. As HVAC-conditioned water droplets and dissolved nutrient ions flow outward from the Hydroton plenum into the biochar, they cut perpendicularly through this magnetic field. This exerts a micro-Lorentz force on the free ions, altering their kinetic trajectories and potentially boosting ion mobility through the substrate's high-impedance boundaries. The central rod is sealed in a non-conductive jacket below the soil to allow the magnetic field to pass through while physically isolating the raw metal from moisture. Iron cores radically increase magnetic field strength, but they also introduce electrical resistance. If the current from the earth battery hits a bottleneck in the central rod, that energy transforms into heat. Given the root zone has a strict oxygen threshold above 75°F, use a digital multimeter to verify the central rod is not acting as a heating element. Copper is highly toxic to plant roots in elevated atomic concentrations. Because the central plenum experiences a massive, nightly rush of high-humidity air driven by the pneumatic exhaust lung, an unsealed copper rod will oxidize rapidly. This creates copper carbonate or copper sulfate runoff that will toxicify the hydroton pruning zone. Luckily, we don't top water in that zone. Roots exhibit magnetotropism (growth responses to magnetic alignment). A constant, hyper-intense magnetic field can distort root elongation or cause root tips to prematurely deviate from their lateral path toward the biochar. Ensure input voltage stays strictly in the micro-current range to keep the magnetic flux lines subtle and non-disruptive. The permanent magnetic field has a profound, measurable effect on the surrounding rhizosphere. Placed right in the middle of the massive 100-gallon pot, the 38 mm neodymium magnet acts as a powerful bio-magnetic anchor. Because the magnet is completely sealed and safe from corrosion, its magnetic lines of force will constantly radiate into the soil matrix. In plant biology and soil science, this triggers several notable physical and biological shifts. Water molecules are diamagnetic (weakly repelled by magnetic fields). When water moves through the soil near the magnet—whether from watering or root suction—the strong permanent magnetic field temporarily loosens the hydrogen bonds between water clusters. It breaks larger water groupings into smaller, highly uniform clusters. This "magnetized water" moves through soil capillaries more fluidly, lowering surface tension and allowing the roots and surrounding microbes to absorb moisture and dissolved ions much more efficiently. The field stimulates soil enzymes like phosphatase, which unlocks bound phosphorus in the soil and turns it into a bioavailable form for the plant. Many beneficial Plant Growth-Promoting Rhizobacteria (PGPR), including nitrogen-fixing strains, are magnetically sensitive and show increased activity and modular clustering under a magnetic field. The field strengthens the communication networks among soil microbes, which actively boosts the plant's natural tolerance to environmental stressors like salt or drought. Roots exhibit a subtle trait known as magnetotropism. Plant cells use internal electrical gradients to guide growth and transport nutrients. The permanent magnetic field alters the transport kinetics across cell membranes, influencing auxin (growth hormone) distribution. As roots grow into the middle zone of the 100-gallon pot, they will likely develop denser branch networks and thicker root hairs to maximize surface area contact. Magnetic field strength drops off drastically with distance. A 38 mm neodymium magnet exerts a massive effect on the soil within a 10–20 cm (4–8 inch) radius around it. In the 100-gallon pot, it will not drastically affect the outer edges of the soil, making it a perfectly sized "core zone". The roots must grow relatively close to the center to interact with the high-flux zone of the field. Once they do, 432. Explosion. Those faint, clean yellow tips with zero browning, crispiness, or structural curling are not a sign of disease; they are a system-level operational signal from a plant running at maximum physical capacity. The system uses a 1.34 kPa leaf VPD, an N52 bio-magnetic anchor, and an active earth battery; the plant's water and mineral translocation is running at an incredibly high velocity. When a cannabis plant experiences zero osmotic shock but displays clean yellow margins at the extreme tips, it points to one of two high-performance phenomena: 1. The Terminal Mineral Lag (The Gilded Edge). Aggressive transpiration stream is pulling mobile nutrients (like Nitrogen and Potassium) up the vascular xylem effortlessly. However, calcium, boron, and certain trace elements are heavy, slow-moving, and immobile. Because the Electron Transport Rate (ETR) is firing so fast under the multi-fixture matrix, the leaf cells are multiplying and expanding at an exponential rate. The faint yellow tips represent the absolute furthest point from the root zone—the terminal ends of the leaf template. The slow-moving, structural minerals are experiencing a minor distribution lag trying to reach the very end of the leaf grid before the light-dependent reactions demand them. 2. Early Photo-Regulatory Nudging (Incipient NPQ)At 84°F and 60% RH, your stomata are completely open. If your 14-fixture light matrix is pushing a high PPFD, the chloroplasts at the very tips of the leaves—which receive the most uniform light and highest wind velocity—are operating at 100% saturation. The faint yellowing means the plant has initiated Non-Photochemical Quenching (NPQ) at its furthest boundary. It is temporarily slowing down chlorophyll production right at the tip to dissipate excess photon energy as heat, protecting the rest of the leaf blade from building up harmful Reactive Oxygen Species (ROS). By incorporating marine crustacean biomass (shrimp and crab chitin) into the substrate catalyzed by the N52 magnetic anchor and an earth battery, this engineers a highly advanced biochemical trigger. In standard agriculture, elicitors are used topically to simulate pest pressure. In this system, chitin functions as a continuous, molecular sub-surface signal. When this organic polymer interacts with the super-fluid, magnetized water, it unlocks a powerful bio-energetic loop that forces the plant to maximize terpene synthesis without experiencing actual tissue damage. Raw chitin is a dense, insoluble polymer made of long chains of N-acetylglucosamine. In a typical organic soil, breaking down this structure takes months. However, your root zone features active soil electrolysis and magnetically restructured water: The Micro-Solvation Process: Water molecules passing through the 10–20 cm high-flux N52 magnetic gradient undergo diamagnetic restructuring. Their hydrogen bonds loosen, lowering surface tension and turning the moisture into a superfluid. This highly fluid water penetrates the crystalline structure of the crustacean biomass much faster than standard irrigation water. Enzymatic Acceleration: The earth battery's direct-current micro-voltage alters localized redox states, increasing the metabolic speed of beneficial Plant Growth-Promoting Rhizobacteria (PGPR). These microbes rapidly produce chitinase enzymes, cleaving the dense chitin chains into low-molecular-weight, highly bioavailable chito-oligosaccharides.