Processing
Likes
Comments
Share
The week was gone very well until yesterday. I happen to check on the girls when the lights came on I noticed one of my two lamps were out. A bulb burnt. It is only two months old. I bought it online and delivery on everything from this company is out over two weeks. They are closed for the pandemic. Surprisingly, a local hydroponic store where I bought my fans and air scrubbers from was open. The guy cut me a solid and $85 later I am back in business. The girls just had one night with one light. I don’t think one cloudy day will hurt them They’re budding nicely, I just pick a few leaves every now and then to get some light to specific buds.
Likes
69
Share
@nonick123
Follow
Día 108 (16/09) Tras el flush las plantas muestran tímidamente nuevos pistilos blancos! 😍 Hoy no es necesario regar! Día 109 (17/09) Me he encontrado a OnionOG #1 y a Purple Punsh completamente sedientas! Con las hojas caídas! Riego con 1,25 litros de H2O a cada una de ellas (el resto no necesitan riego) Día 110 (18/09) Riego con 500 ml H2O Las plantas con el bloqueo empiezan a mostrar nuevos pistilos, sobre todo en las partes inferiores Día 111 (19/09) Riego con 250 / 500 ml H2O Se vuelven a formar pistilos blancos en todas las plantas que han sufrido el bloqueo! 😍💥 OnionOG #1 va como un cohete formando y apilando flores 💪 🚀 😍 Día 112 (20/09) Día lluvioso. Riego ligero 250 ml H2O Día 113 (21/09) Otro día lluvioso. Riego ligero con 250 ml Día 114 (22/09) Detecto algunas moscas blancas apoderándose de las plantas y decido hacer una aplicación foliar de piretrinas (Spruzit a 15 ml / l) Riego con 1 Litro de Té Floración de Lurpe Solutions. Preparación: 24 horas con bomba de aire (oxigenación) con ingredientes: Healthy Harvest 8 ml/L + Insect Frass 16 ml/L + Kelp Hidrolizado 0,3 g/L 💦Nutrients by Lurpe Solutions - www.lurpenaturalsolutions.com 🌱Substrate PRO-MIX HP BACILLUS + MYCORRHIZAE - www.pthorticulture.com/en/products/pro-mix-hp-biostimulant-plus-mycorrhizae
Likes
Comments
Share
Likes
3
Share
So we have entered week 3 for these aptus fed girls and I think they had a slow start after transplant but soon perked up Allthough the growth of branches ere not as quick too develop as I would like but any comments are welcomed They are healthy just not as explosive with growth so hopefully over the next week they get comfy and take off 🤞 This is my first time using aptus so I expect myself too need too adapt. I am sure they will be fine, I also have 2 icc from Humboldt which have been late starters so I'll be potting those up this week and they'll join the older girls on the next update 🌱 I'll also be doing some slight lst with the untopped girls too provoke strength and hopefully push them too grow. Much love and stay blessed 💚
Processing
Likes
6
Share
It's a shame my ventilation system came in a month after I grew mold but at least I can make some brownies with about 25 grams of some pretty dank bud.
Likes
34
Share
@Mom74
Follow
Nach der Entlaubung letzter Woche haben sich die Pflanzen gut erholt und im Netz entfalten lassen. Die Blütenansätze sind nun deutlich sichtbar. Der Geruch ist moderat und die Temperatur und Luftfeuchtigkeit konstant. Bin gespannt wie groß die so werden. Ist mein erster Grow von Photoperiodischen Pflanzen.
Likes
13
Share
@gr3g4l
Follow
timelapse de los últimos 35 dias a 12/12h. SECANDO . Durante los primeros dias las temperaturas en exterior eran aun fresquitas y el secado se hizo con un calefactor de 80W, deshumidificador y ventilador para que corriera el aire , una semana áproximadamente , luego se quitó todo y se dejó sin nada para que siguiera secando poco a poco dentro del armario de secado. pasados 21 dias secando y las plantas estaban ya bién secas y crujientes, igual demasiado , las puse ahí dentro y más adelante sin prisas en botes herméticos para curarlas y salgan aun más ricas. Bueno gente, ahora si que puedo decir que hemos teminado con este seguimiento y espero que os haya gustado y sobretodo que pueda ayudar a alguien que se inicia en este mundillo. Nos vemos en otros seguimientos. Salud.
Likes
2
Share
@mojogrow
Follow
I was seeing that this genetics has a problem with the leaves, it has white spots and leaves with a quite peculiar development. There is no plague in the indoor and the conditions I think are the right ones the euphoria is better now, more steady, I gave her 2 ml of bioheaven, 1 ml of biogrow and 5 ml of trimix pro.
Likes
17
Share
@Lazuli
Follow
She got slowed down a lot because she was grown during winter in temperatures between 16 and 20 celcius
Likes
106
Share
Still no sign of flowering. Transplanted Novarine plant 2 into a 50-liters container. The spot is under a big shorea plant. Shorea is a South East Asian medicinal tree. This is minimum light spot in my yard. Hope she would flower. I choose plant 2 because I think plant 1 will stretch even further. Plant 1 was also moved to a shaded spot under an tree jasmin. This Millingtonia, Indian cork tree. I have sweet flowers all year round. People told me that dried tree jasmine flower mixed well with weed and is good for people with ashma and sinus. Kind of useless since why would asthmatic people even smoke? Plant 3 is my back up until I come up with a way to put her into flowers. Clone are doing nicely. And I am growing 3 clones from plant 1 and only one clone from plant 2. I’ll be donating the rest to friends with weight and blood sugar issues. By year end, I probable keep only one or two clones. One clone from bigger branch is growing just fine without any benefit form lighted grow box. Feeding plants with mid-level dose of cow manure tea and earth worm casting tea to keep leaves healthy. They should have been given a light dose of fertilizer. However, the flowering purslane are also eating and feeding soil microbes. Got my paws on triancontanol and brassinolide. Perhaps these will jolt Novarine THCV into flowering. Triacontanol won't dissolve in neither water nor alcohol. And it is emulsified with polysobate. Mixing of Triacontanol Triacontanol does not dissolve in polysorbate. It is rather emulsified. Means that it need to be melt and there need to be water added. My steps, 1) heated 70 grams of polysorbate in a big heat resistance glass cup. I used a beaker. Mix in 5 grams of triacontanol. And it does not melt. 2) Put in 100 cc of water and put in microwave. After the mix is boiled, triacontanol melt. There is foam. So a bigger cup and a spillage plate would prevent problem with my better half. 3) After heated, the mix is better. Then I added hot water from to make total 250 CC of solution. Then, the mix is clear. 4) Label the dose with pencil. This works better than labeling with ink. I use 5 cc at a time for my entire garden. 250 CC would last me 50 doses. No need to buy so much. This is cheap. Let’s see next week how effective they are.
Likes
11
Share
Likes
14
Share
@MG2009
Follow
03/13/2022 Love the colors on Grape Skunk #1 others are not as purple, again i forgot Biscotti Skunk and lemon og. 03/14/2022 Uploading Biscotti Skunk pic's I'm really loving 3 particular girls this run,all plants are exposed to PW intentionally I need girls that can take PW with no issues and three plants are spotless. The first is the only Biscotti Skunk that was female of 5 cloning for outside run but will do great in basement without PW issues. The second is lemon og spotless, and the third is the grape skunk thats got most color the second tallest of the grape skunks, cloning for testing in New England zone 7 should get at least one if not all 3 to finish before cold sets in.
Likes
49
Share
Day 28 - Full watering/feed to run-off 10%-20% at same strength as previous. (50% of maker recommended strength for coco use + cmx + root enhancer + kept extract organic additive) Day 31 - Decided lower lights by around 30cm 120cm to about 90cm. After about 8 hours the plants all suddenty wilted. They stay wilted through the night cycle as well, so I raised the lights back to where they were and they have bounced back, so I won't suddenly drop the lights by as much. If I do lower them it will be incremental. Day 32 - Bought a six fin 800w oil heater for the tent. Am going to place this under the oscillating fan and set it aiming to keep the tent around the 25-27c range. Hopefully this has the tent sorted for the rest of the grow. The humidity has been high lately due to the weather, so this might be about the only factor left to address, and I will look at getting a dehumidifier for the grow room if needed. Day 33 - Full watering to run-off 10%-20% at same strength as previous. (50% of maker recommended strength for coco use + cmx + root enhancer + kept extract organic additive) - Ordered humidity controller for extractor fan. - Ordered Temperature controller for Heater - Ordered IP Camera for remote monitoring Tent is now running fully sealed and using passive inlet and carbon filtered extraction to roof space. Plants are around 20-40cm high and the lights are 85cm above the canopy on full 480w. Day 33 - I have reduced the Light intensity from 480w to 420w. This seemed to really get a good response from the plants. I think as they've grown taller and the light intensity has quietly increased at the newly heightened canopy level the plants have been getting stressed. Day 34 - I've reduced then light intensity from 420w to 280w. I am new to the quantum boards and the concept of "too much light" so working out how much intensity, how much distance and so forth for the different stages of plants growth. I have a gut feeling 280w at 80cm might be a touch under-powered but I'll give it a full light-cycle or two to judge leaf growth and colour and make a call on whether or not to increase it or leave it as is. Day 35 - I found plants wilting during hthe night cycle without fan air circulation. So I've set the oscillating fan to run during night hours. Day 35 - I've turned up the heater a touch to bring the tent temp to around 26c. Infrared gun shows leaf temps to be around 24-25c which ideally I want to get to 27-29c - I'll aim for this metric once the other environmental factors are sorted (ventilation seems sorted so mainly just dialing in the light intensity). * I'm looking forward to setting up the heater on temperature controller, and putting the carbon filter ventilation on humidity control, and then mounting an IP camera in the tent. This should all be here in around 2 weeks. I'm looking forward to being able to view the temp/humidity and see the plants live without having to actually open the grow room. * The infrared temp gun is proving invaluable in testing leaf, coco and pot temperatures around the tent, which is giving a great view of how the heat from the heater/fan arrangement is being distributed - it shows a less than 1-2c degree variance across the tent which is just great. * Hopefully week 6 to come will be one with a lot less wilting incidents and the week that this tent achieves a somewhat final and stable environment optimised for plant growth and happiness. But so far every time I think I've got things perfected, another variable comes into play and I need to tweak something. Maybe by the end of this harvest I will have the whole process refined to a smoother less reactionary process.
Likes
44
Share
@rhodes68
Follow
9/7 Day 7 Things are ok watching Jen closely and dropping PH slowly from 6.8 to 6.0 by the gauge (no more dye... yea) to see if its a lockout. Lowered lights to 24 inches as I am seeing a bit of stretch. Just learning how to use the light in absence of anything approaching instruction :) Folks I like this light, so far... awwwwright Transplant time coming up in a week or so, be getting the pots ready with a full wash of nuets just to get things rolling in the soil. 9/11 D11 Transplanted to five gal pots, soil is mix of 707 with 1 tbs Recharge , 3 tbs Dolimite lime, and 5 tbs Happy Frog Guano Culture , Watered with feed of Kanga/Fish Mix/Big Bloom 0.5 gal each Staying on 24 hr lights till end of week 9/14 D14 Finishing the week up with a feeding Fish Mix 1 tsp/gal Big Bloom 1 Tbs/gal for 2.0 liters Lights now on same timer as the CBD - 20-4
Likes
32
Share
Info: Unfortunately, I had to find out that my account is used for fake pages in social media. I am only active here on growdiaries. I am not on facebook instagram twitter etc All accounts except this one are fake. Have fun with the update. Flowering day 33 since time change to 12/12 h. Hey everyone 😃. Another wonderful week goes by :-). The lady is developing very well. The flowers begin to develop properly and already smell very nice 🙂. The day before yesterday was the last time 1 g of GHSC Powder Feeding per L substrate was added :-). That should last to the end now. Of course, she continues to receive GHSC enhancers 👍 every 14 days. The tent was cleaned every day just like the humidifier was refilled every day. I am very curious how it will develop in the coming week and until then I wish you a lot of fun with the new update. Stay healthy 🙏🏻 and let it grow 🍀🙏🏻 You can buy this Strain at : www.Zamnesia.com Type: Banana ☝️🏼 Genetics: OG Kush x unkown 👍 Vega lamp: 2 x Todogrow Led Quantum Board 100 W 💡 Bloom Lamp : 2 x Todogrow Led Cxb 3590 COB 3500 K 205W 💡💡☝️🏼 Soil : Canna Coco Professional + ☝️🏼 Fertilizer: Green House Powder Feeding ☝️🏼🌱 Water: Osmosis water mixed with normal water (24 hours stale that the chlorine evaporates) to 0.2 EC. Add Cal / Mag to 0.4 Ec Ph with Organic Ph - to 5.5 - 5.8 .
Likes
49
Share
@AsNoriu
Follow
Day 119. Will update later. This grow is almost finished .... Jar day - all is done, now cure left. Happy Growing !!! P.S. if you are searching for Killer Kush, she got separate diary, my favourite of all 3 strains.
Likes
47
Share
*****🤔🤔🤔 quick question if anyone can help out I've only been giving these ladies canna start and im a little worried about other nutes going in they are both filling out but just not sprouting in height any help and advise much appreciated***** canna start and small amounts of both the canna start and the water keeping an eye on temp fluctuating more than I'd like and humidity is a little up then down I need to make sure I can keep the same regulation on this so eyes on at all times ....Happy growing friends
Likes
2
Share
@Fireproof
Follow
Ich habe die Erde von meinem Outdoor Grow wieder verwendet: Das war in einem 12l Stofftopf als Basiserde BioBizz Light-Mix mit Bio Tabs 50g Startrex und 5g Mycotrex wie in der Anleitung angegeben. Dann habe ich zwei neue Langzeitdünger Tabletten ca. 10cm tief in die Erde eingebracht. Anschließend mit 1g/l Bactrex und 10ml/l Orgatrex in 1l Wasser aufgelöst und gegossen. Lampe zunächst auf 30cm Abstand zur Erde. Nachdem der Sämling etwas gespargelt hat, habe ich die Lampe auf 15cm gehängt. Die beiden Umluftventilatoren laufen meistens 10h pro Tag, da sie mir aktuell im Home-Office noch zu laut sind. Die Lampe ist auf 40% gedimmt. Die Abluft ist noch aus. Temperatur liegt bei 24 Cº, bei 60-80% Luftfeuchtigkeit. Details: 15.10.24: Samen in Wasserglas 21.10.24: Samen ist gekeimt, direkt in großen 12 l Topf mit BioTabs Erde vom Outdoor Grow, 12l Stofftopf auf Fensterbank 22.10.24: Topf ins Zelt gestellt 23.10.24: 2xBioTabs Langzeitdünner in Erde gedrückt. Mit 1l Wasser gemischt mit 1g Bactrex + 10ml Orgatrex gegossen 24.10.24: Geschlüpft 25.10.24: 09:30: Scheint etwas zu spargeln, Lampe von 30 auf 15 cm geändert. / 17:00 Höhe Stamm: 30 mm 27.10.24: 09:30: Höhe Stamm: 35 mm / Abstand Lampen zu Blattspitze: 10 cm Habe mich gefragt, ob der Abstand der Lampe nicht zu gering ist. In https://www.weed.de/wissen/anbau/hanf-wachstumsphasen steht folgendes zur Sämlingsphase. ✅ Lichtquelle positionieren: Positioniere die Lichtquelle etwa 5-10 cm über den Pflanzen, um das Wachstum zu fördern und ein Ausdünnen (Stretching) der Sämlinge zu vermeiden. ✅ Luftzirkulation: Eine leichte Brise, erzeugt durch einen Ventilator, stärkt die Stängel und verhindert Schimmelbildung. Stelle sicher, dass die Luftzirkulation sanft ist, um die zarten Sämlinge nicht zu beschädigen. ✅ Eintopfen: Wenn die Wurzeln der Sämlinge das Anzuchtmedium durchdringen, ist es Zeit, sie in größere Töpfe umzupflanzen. Verwende ein gut durchlüftetes, nährstoffreiches Medium und sei vorsichtig, um die empfindlichen Wurzeln nicht zu beschädigen.
Likes
3
Share
So the end of 3 and entering week 4 these girls are a little sad today as been working on finishing their little grow space which hopefully they'll settle into over the next few days. I have tried too upload images but no luck keeps saying resizing no matter where I upload from 🙄 The girls are taking off and I can see the difference in growth allthough they've been unsettled past few days 🌱 Still loving the aptus range and so am I its keeping these girls healthy even the topped girl hasnt really reacted too being topped 🌱👌 I will be doing some hst/lst with the other 2 this week as neglected them slightly as having the fastbuds testers all potted up into new shoes. I will try update more images tomorow... Stay blessed 💚