Likes
52
Share
The week ends Mar-31, being day 91 - week 12 of flowering since flipping the lights / day 75 since from first pistils shown. This strain is expected to flower 60-70 days. Harvested the plant in 2 stages over a 10 day period. Lower buds got exposed to more light and definitely seem to have ripened further since the tops were harvested. Fertigation was resumed using GHE Ripen for first 5 days followed by a flush and water only (no pH adjustments) for the last 5 days. The remainder of the plant was trimmed, manicured and separated into A, B grades and trim/larf buds. The buds and sugar leaves are completely covered in resin glands - glistening away in every angle. This last harvest was done after an extended period of darkness (24hrs). Trichomes across the board looked good and ready with 70% cloudy, 10% amber and 20% clear. The water consumption definitely was slowing down in the last week. The drying buds have a very strong strawberry smell after being hung, whilst during the harvest and trimming there was no noticeable scent of weed. Really great stealth type of plant for harvesting :) Using the tent now as a drying area maintaining a higher humidity of 50-60% between 17-19*C, hopefully to extend the drying period whilst hung. Buds are placed in jars once dry to touch then managed until in the curing zone. ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- The grow setup includes; - Secret Jardin DS120W tent (120cm x 60cm x 180cm) placed inside the bedroom. Passive & active intake of air is from a closed off section of the room where the central heating boiler sits - the intake is warm air (20 degC.) and fairly dry (40% RH) during the winter months. - Mars Hydro SP250 LED light - extraction fan - AC Infinity Cloudline T6 - ventilation fans - aquarium heater - small oil heater - small dehumidifier - 20L Airpots and 3.5L general pots for seedling stage - Canna Coco substrate and nutrients - GHE Flora trio nutrients - pH and EC/TDS meters - 2x Govee Thermo/Hygro meters (one at canopy the other at the roots level)
Likes
32
Share
Likes
18
Share
Just a little defoliation this week, not much else. The main cola is getting nice and big and it’s very dense. The rest of the coals are not very big but this plant has got little buds growing all over the place. I think this plant still has a couple of weeks to go but will have to wait and see, the pistils are still pretty white. This is my first time growing so i don’t have anything to compare this small size to, might be genetics or it might be that I stunted this early on by not watering from the bottom or wrong water ph or what have you.
Likes
12
Share
@Natagoat
Follow
This week has been another good week ive increased feeds as she is super thirsty and getting watered every other day other than that ive let her get on with her thing. Ive gotten a new usb microscope and had a bash at taking pics with that, but its going to take some practice to get good images until I chop and use the stand or make my own stand.
Processing
Likes
13
Share
Day one of this week entailed me going to the hydro shop, grabbing so blue sky organics super soil, some 1 gal fabric pots and off I went. I always pot my soil then water the pots down and wait 24 hours for everything to acclimate so as to not shock my seeds. I germinate straight into the soil. I will post more pics to beef up this week! I will be planting 2 fastbuds orange sherbet beans, 1 in a 1gal fabric pot and 1 in a 3gal from the bucket company.
Likes
24
Share
So she had some nice growth this last week. I'm hoping this next week is its last bit of growth, can only move the light up another 3 to 4 inchs. I've got to clean up the lower section A bit more, more growth there then I'd like. So far it's growing a lot nicer then the last plant I did in this tent with a SCRog set up. The size of the squares on the last grows netting were 6" and this one is 4". Way easier to get a proper looking SCRog plant then with the 6" that's for sure. Now that the temperature outside has warmed up the night time temperature has been better then earlier weeks. The humidity has also gotten a lot better. Especially after I add a 4" muffin fan to the lower 4" duct hole. The humidity went up but the temperature went down a bit during lights on. Ive had to lower my temperature switch just to get the 4" duct fan to turn on to suck out the stail air. Think what I'll do is add a second plug to the temperature switch so I can add the 4" muffin fan to it so that itll only turn on when the temperature goes up instead of running 24/7. I've increased the feed up to 1000ppm and am give it 1.5L of water a day with 250ml max run off. My run off ppm is only 1080ppm so that's a great sign so far. I've been trying my best to keep the ppm levels equal every feed but itf luctuates a bit but no more then 60-80ppm. Same with my Ph, because I'm using the Jungle Juice base nutrients it's not part of Advanced Nutrients Ph perfect line so I have to adjust it. I usually try to have it swing back and forth between 5.9 and 6.1 and the plant seems to be liking it. Tho I'm not done this grow yet this light is doing a lot better in this tent then the last light. Only downside is that one burnt out diode. Because I always try to plan a grow ahead, I'm already planning on trying that last light out again (Phlizon PH-1000 125w that they apparently don't make anymore). But this time it's going to be in my 2x3x5 fusion hut tent with Royal Queen Seeds Fast Eddy CBD AUTO strain. Also going to add a ex hale bag to it. Well that's all for now growmies. Keep growing!!!
Likes
21
Share
Been another smooth week. A few of the plants are starting to show signs that they are moving towards to finish line. Seeing some swelling, pistils starting to brown, and some beautiful purples coming out in some of the buds. Been debating on giving them a dose of dry koolbloom, but I will probably just keep them running on the maxibloom until flush since they look pretty happy. This slurricane is busting with sweet fruity aromas. Not going to be the best yield but I'm sure she will pack a nice punch.
Likes
5
Share
Pulled down side branches using Twisties. Will be putting her on to flower soon.
Likes
9
Share
All the photos are in the 8x8 now just a few autos in here now FOR EVERYTHING MARS HYDRO VISIT: www.mars-hydro.com www.marshydroled.ca PROMO CODE: rocknroll VISIT THE ALIEXPRESS STORE: @marshydro_aliexpress Instagram: @marshydropenny Thanks for taking the time to read and check out my diary🤜🤛 (NEW) STRIVE NUTRIENTS 💪 TS3000 FEATURES: WIDEBAND SUNLIGHT FULL SPECTRUM LED GROW, Infinite close to natural sun light, suit for all plants whole stages indoor growing, rapid plant response from seed to flower, achieve maximum quality and quantity, much better than traditional HPS grow systems. HIGH REFLECTIVE & NOISE FREE-Fanless LIGHT BOARDS design will make your growing life easy and quiet, quickly heat dispersing material aluminum reducing light lost to aisles and walls, increase the light intensity up to 20%, allowing your plants receive more energy and without burning your plants for maximum headroom. HIGH EFFICIENCY ENERGY SAVING PLANT LIGHT, high-power NEW LED grow, Compares to traditional 3000 watt HPS lamp and other brand led grow light while only 450 watts true output with 1016 LEDs, more scientifically and energy-efficient! Perfect for 5' x 5' veg stage, 4' x 4' bloom stage, higher intensity in a MARS HYDRO grow tent, reflective area, or by crossing over using multiple TS3000. BOOM YIELD LARGE GROW LIGHT, NEWEST SMD LED technology provide highest PAR/LUMEN output(1095.6umol/), makes you get 30% higher yield compare OLD led lights, can get max yield at 2.5g/watt, less pay but get more yield, bring a amazing grow trip to any home grower as it beams huge amounts of light energy to plants below. COMMERCIAL LED GROW LIGHT, Updated easy dimming & daisy chain function, main light controlled, especially come with two waterproof and dimmable Mean Well Drivers, auto sensing power supply works on both 120VAC and 240VAC and 277VAC, suit for Large Rooms and Commercial Setups. Low Energy-Consuming LED Grow Light: Consuming 300w and also mounted with 1016 chips, TS3000 has the ability to replace a 450w HPS light while reducing 40% power intake. High Efficiency LED Grow Light: With overall light output PPF 343umol/S as well as amazing PPE 2.3 umol/j, it's 50% even more photon efficient and can assure a 30% more return than the old HPS/MH lights. Patent Highly-Reflective Hood Shape: The reflector design on TS3000 is patented, which can effectively gather the light dispersed in all directions to enhance its light intensity as well as assist plants in absorbing more light. Full Spectrum Plants Favorite Spectra: By the unique mix of spectra that makes most light in the 400-700nm waveband, incredibly conducive to plant photosynthesis. Adequate IR(730-740nm) is additionally consisted of in the range to generate larger buds. Dimming And Daisy Chain Feature Available: Upon an independent dimming button on the external driver, backing 0-100% settings adaptation and up to 30 LEDs daisy-chained in a group, it supplies different light levels for various plant stages meanwhile saving energy. Safety Certifications And Service Warranty: CE, ETL, RoHS, UKCA security certifications accepted, 50,000 hours durability, 5-year service warranty, and local after-sales repair 5x5 GROW TENT: LOCK ALL LIGHT INSIDE MARS HYDRO Indoor Grow Tent interior is made of diamond mylar which is highly reflective. (Other brand's mylar and reflective rate is as low as 50%, won't provide efficient light. )MARS HYDRO 1680D canvas, being double stitched, it is tear proof and has perfect light locking. Mars Hydro's grow tent keeps 100% lighting beams inside and helps your plant absorb more lights. EXTRA-THICK --No light leaks or rips at all DURABILITY GROW TENT Stable metal corner adapters and poles are the trustful supporters of the tent, standing sturdy, neither rusting nor paint-falling, quick easy tool-free installation. Mars Hydro's heavy-duty metal zippers, with double layer black lining, are the best on the market which create a light-proof seal EASY OBSERVATION FOR YOUR PLANTS. Special observation windows are made by double layers of cloth. Observe the growing conditions of your plants without opening the tent and avoid disturbing plants. The observation window also serves to dissipate heat and ventilate air AUTOMATIC 6 INCH EXHAUST FAN KIT W/ CONTROLLER: Mars Hydro 6'' Inline Fan uses a mixed-flow design to maintain peak performance in a high static pressure environment. GROW TENT FAN: MARS HYDRO inline fans are designed to ventilate hydroponic grow rooms, transfer heating/cooling, cool AV closets, and exhaust odors. EFFECTIVE VENTILATION: Variable speed controller for easy fan speed adjustment. Optimal ventilation for your planting. LOW NOISE LEVEL: Durable plastic fan housing and blades for extremely low noise(32dB-A); create a truly quiet growth environment. EASY INSTALLATION: Removable duct ends with locking tabs for quick removal and easy maintenance and a cord length of 4.9 feet for hassle-free setup. This grows tent fan with a controller for easy fan speed adjustment. BASIC PARAMETERS: Ventilation exhaust fan size: 6” | Dimensions: 315mm*225mm*210mm. | Weight: 2.7. | Airflow: 402CFM | Noise: 32dB-A | Bearings: Dual Ball. 
Likes
94
Share
Could have done a much better job overall but I'm pleased with it anyway as the plants produced some really nice smoke 🙌
Likes
5
Share
@Budzalot
Follow
Day 28. Trim them 3 times last week. Trying to figure out how much stretch I'll get with led lights. Haven't used led forever. Grew this last grow under hps got 571 grams with 600 hps.
Likes
1
Share
Pics are from day 19, which is the day I topped all the plants. Topped them for a second time a little early - should have waited a couple of days for the new growth. No real damage done though and a lesson learned. Topped to the 3rd node, stripping everything below, and topped each "stork" at the next node creating 4 main branches per plant. Seen a little cal deficiency, but increasing the feed concentration to 2.5ml p/l of each will nutrient type sort that out in the coming week. Will be transplanting to 5 gallon pots in the coming week, once the plants have bounced back from the heavy mainlining techniques they've just been through.
Likes
120
Share
@StarLorr
Follow
Welcome to my Strawberry Pie 🍓🥧diary. In this Diary: Seeds: [420 Fast Buds]from my growmie Tropicannibis_Todd 👊🏻😎 Media: Pro~Mix HP Open Top Grow Bag, Connect. Nutrients: Green Planet Nutrients, 2 Part Dual Fuel starter kit. RealGrowers: Recharge. Diablo nutrients: Supplements. Feeding : Wed 06Mar: 3 1/3L Nuts/Recharge pH'd 6.5 Sat 09Mar: 2L Monster Flower,Blaster pH'd 6.5 Mon 11Mar: 3 1/3L Nuts/Recharge pH'd 6.5 ___________________________ D-Fol: 10Mar keeping up with the fan leaves😄 __________________________ She's getting smelly and sticky😋 Buds are getting bigger😁 Some pistils are changing colors. ___________________________ Thanks for stopping by, likes and comments are appreciated.👊🏻😎 Keep on growin! Keep on tokin!!! 😙💨💨💨💨💨
Likes
58
Share
Day 95 — Currently waiting for Milk to turn Amber — Vibe: 💪 Day 97 — Trying not to view these endlessly — I'm ready to chop the plan on the right, She's not ready to be chopped yet... — Vibe: 😴💤 Weekly Avg Readings — Lights 12/12 - Level 10 — Temp: 70 (ideal) | 72.8 (avg) — Humidity: 60% | 62.0% — VPD: 1.2 | 1.02 kPa "They hear the hunger in my voice, shit I went broke twice. 4,000 lights at a real low price." —Berner415
Likes
35
Share
@Eryan
Follow
Harvest starts today on Day 56. 36 Hours of darkness begins now. Watered yesterday. Don't have time to upload/process photos, will do so later. For now just the one video of trichomes. You can also see an unwelcome guest at the beginning, although I'm not sure if it's a spider mite. Not taking any chances though, and the trichomes have begun to decay anyways, so harvest time it is. I'm kind of in shock about reaching this point in the grow 😨 Day 57 - Harvest early tomorrow :) Going to control the humidity to be about 55%. Day 58 - Harvest. And oh my god that smell. Is...Grape soda, which has been sweetened a little too much. It's overpowering when smelling it, but it doesn't get the room too smelly (also have decent ventilation though). I'll post harvest and effects later, after it has dried for a few days and then cured for a week or two. Yield won't be much I think, somewhere between 20-30 grams. Wet weight with stems is around 75.
Likes
7
Share
This ladies look absolutely gorgeous and super strong, they're gonna be flipped into flower tomorrow on February 15th when they'll hit the 30th day since they were planted and the first day of flower! As said, I have flipped this ladies into flower on February 15th so now I think we're gonna see a beautiful stretch specially on this 2 plants which are the biggest one in the tent, very nice genetic, cannot wait to see their performance ❤️💛💚👨‍🌾 stay tuned everybody! This is gonna be a beautiful run! ✌️
Processing
Likes
7
Share
@Mrg7667
Follow
Amazing week! Starting to smell absolutely Devine! Some cherry funk to cherry funk with a hash back and some with just lighter hashy lind of smell all looking great except one oheno growing funky finger nugs (one of the better smelling phenos tho) Need to clone 4,6,3!