Chat
RecommendedRecommended

Auto Purple Hulk ️

9
5
241
3 years ago
Follow
Germination Method
Other
Method used by growers
Statistics by method
Avg. success - 93%
Method popularity - 6%
Purple Hulk Auto Feminized
Avg. success
MSNL - 91%
Purple Hulk Auto Feminized - 75%
Commented by
FuZzY619 FuZzY619
3 years ago
Started in aerogarden and will move to Hydroboy in a week. Sprouted in 24 of germination in aerogarden. Normally 100% germination when I use the aerogarden to start
Similar Diaries
Zomby Kush
1 weeks
Zomby KushHydra
Zombie Kush
11 days ago
Gorilla Glue Auto
6 weeks
Gorilla Glue AutoOlli_Who
Gorilla Glue Autoflower
11 days ago
Tropical Mirage Clone
3 weeks
Tropical Mirage ClonePatriciaGant
Tropical Mirage
11 days ago Β· 1 comment
Fast Buds meme contest
6 weeks
Fast Buds meme contestJabba23x
Blackberry Auto
10 hours ago Β· 1 comment
Apple Friter
2 weeks
Apple FriterRandom80
Apple Fritter Automatic
11 days ago Β· 1 comment
Grow Questions
FuZzY619
FuZzY619started grow question 3 years ago
I'm growing out of a 3.5 gal hydrobucket. I've read that it's good to lower the water level by 1"-2" inches to promote root growth.. is this true or should I keep my water level where I started it at? Thank you.
Solved
Roots. Too few
like
TickleToast
TickleToastanswered grow question 3 years ago
Once you have roots popping out the bottom of your netcup (about a week or so after transplanting) most all DWC users will then drop their water level to 2'' below the netcup - let it drain a couple days and then check the solution, assess, and then get it back to 2'' below the netcup again with w/e you needed (plain water / nutes). This is very "heath robinson" and has worked for many growers for a very long time. You CAN improve upon this - your head is in the right place. I started with the above standard and eventually moved away from it a bit. I let my buckets drain and don't fill all the way back up to 2'' anymore - creating some drought stress and naturally boosting root growth as it drains (plus the pruning stress from your bubblers + a root stim and πŸš€πŸš€πŸš€). Now doing this does jack up your PPM a little bit, but so long at your below 2k and all is well, your plant will be fine - in a well acclimated hydroponics system the plant can take it!
FuZzY619
FuZzY619started grow question 3 years ago
To get an EC value, I must multiply the ppm reading by 2 and divide by 1000. But my TDS tester gives me both microSiemens and ppm reading.. which measurement do I use to get the correct EC value, microSiemens or ppm?thank you in advance.
Solved
Other. General questions
like
m0use
m0useanswered grow question 3 years ago
Often the literature will use microSiemens (uS/cm) and EC standing for electrical conductivity. These two units are the same. http://www.maherjabado.com/ec-ppm-table.JPG Just may need to round the decimal point over a bit to get a EC of 1.0, Depending on the scale 500ppm or 640ppm 700ppm is all 1.0EC, That's why EC is more accurate then PPM. PPM is not truly accurate because all TDS pens do is measure EC. A true PPM count is done with a different machine. If you make a solution and test its EC at 1.0 or 1000ms/cm, then switch it to ppm you will find your scale. If your meter says 500ppm then you know that's your scale. Can test with salt water and save nutrients. Good Luck!
Comments
Login

Show by Week
Sort by
popularity
popularity
newest
oldest
homerjgangia
homerjgangiaweek 0
Good luck with your grow mate!πŸ’ͺπŸ’ͺ
homerjgangia
homerjgangiaweek 0
Good luck with your grow mate!πŸ’ͺπŸ’ͺ
Y0ink
Y0inkweek 0
We do what we got to do 😎 Good luck whit your grow mate πŸ‘ŠπŸ½πŸ€πŸ€ž
Balankaya
Balankayaweek 2
Hello comrade! Great job, good luck to you!
CannaKrops
CannaKropsweek 3
Good luck on your grow! 🌱🀞πŸ’ͺ
Kynareth
Kynarethweek 3
nice plants buddy