Chat
RecommendedRecommended

Auto Purple Hulk ️

9
5
241
3 years ago
Follow
Grow Conditions
Week 2
Vegetation
6.35
cm
inch
Height
18 hrs
Light Schedule
11+ conditions after
Login
Nutrients
ml/l
ml/gal
tsp/gal
Commented by
FuZzY619 FuZzY619
3 years ago
The transfer from aerogarden to bucket went well she settled right in. Running 18 hr light cycle.
Similar Diaries
Peanut Butter Breath
1 weeks
Peanut Butter BreathSkunkyDog
Peanut Butter Breath
4 minutes ago
Organic Exotic Genetix
19 weeks
Organic Exotic Genetixohighoan
+3 strains
30 minutes ago Β· 3 comments
First real Grow with a litte Mutant - Zamnesia Wurlz F1
13 weeks
First real Grow with a litte Mutant - Zamnesia Wurlz F1MrGoonai
Wurlz F1 Automatic
2 months ago Β· 16 comments
2- auto
13 weeks
2- autohampfi
2 strains
2 months ago Β· 12 comments
Rs11 x Hollywood by Cookies
20 weeks
Rs11 x Hollywood by CookiesBlackForestGrower
Hollywood
3 days ago Β· 10 comments
Zamnesia Runtz
16 weeks
Zamnesia RuntzJipserNight
Runtz
a month ago Β· 21 comments
Girl Scout Monkeys
4 weeks
Girl Scout Monkeys DisTentAint4Campin
Illuminauto #56 - Girl Scout Monkeys
3 months ago Β· 1 comment
Air-DWC-2W
13 weeks
Air-DWC-2WHigh_And_Hydro
+1 strain
2 months ago Β· 22 comments
Grow Questions
FuZzY619
FuZzY619started grow question 3 years ago
I'm growing out of a 3.5 gal hydrobucket. I've read that it's good to lower the water level by 1"-2" inches to promote root growth.. is this true or should I keep my water level where I started it at? Thank you.
Solved
Roots. Too few
like
TickleToast
TickleToastanswered grow question 3 years ago
Once you have roots popping out the bottom of your netcup (about a week or so after transplanting) most all DWC users will then drop their water level to 2'' below the netcup - let it drain a couple days and then check the solution, assess, and then get it back to 2'' below the netcup again with w/e you needed (plain water / nutes). This is very "heath robinson" and has worked for many growers for a very long time. You CAN improve upon this - your head is in the right place. I started with the above standard and eventually moved away from it a bit. I let my buckets drain and don't fill all the way back up to 2'' anymore - creating some drought stress and naturally boosting root growth as it drains (plus the pruning stress from your bubblers + a root stim and πŸš€πŸš€πŸš€). Now doing this does jack up your PPM a little bit, but so long at your below 2k and all is well, your plant will be fine - in a well acclimated hydroponics system the plant can take it!
FuZzY619
FuZzY619started grow question 3 years ago
To get an EC value, I must multiply the ppm reading by 2 and divide by 1000. But my TDS tester gives me both microSiemens and ppm reading.. which measurement do I use to get the correct EC value, microSiemens or ppm?thank you in advance.
Solved
Other. General questions
like
m0use
m0useanswered grow question 3 years ago
Often the literature will use microSiemens (uS/cm) and EC standing for electrical conductivity. These two units are the same. http://www.maherjabado.com/ec-ppm-table.JPG Just may need to round the decimal point over a bit to get a EC of 1.0, Depending on the scale 500ppm or 640ppm 700ppm is all 1.0EC, That's why EC is more accurate then PPM. PPM is not truly accurate because all TDS pens do is measure EC. A true PPM count is done with a different machine. If you make a solution and test its EC at 1.0 or 1000ms/cm, then switch it to ppm you will find your scale. If your meter says 500ppm then you know that's your scale. Can test with salt water and save nutrients. Good Luck!
Comments
Login

Show by Week
Sort by
popularity
popularity
newest
oldest
homerjgangia
homerjgangiaweek 0
Good luck with your grow mate!πŸ’ͺπŸ’ͺ
Y0ink
Y0inkweek 0
We do what we got to do 😎 Good luck whit your grow mate πŸ‘ŠπŸ½πŸ€πŸ€ž
Balankaya
Balankayaweek 2
Hello comrade! Great job, good luck to you!
CannaKrops
CannaKropsweek 3
Good luck on your grow! 🌱🀞πŸ’ͺ
Kynareth
Kynarethweek 3
nice plants buddy