'Glookies #2' by Barney's

Hey all. This is just an equipment schedule and initial propagation pictures. Much less about the plants and more about the automation and acclimation settings I will be running for this grow as I try to make things a little easier for myself and create a better environment for the ladies. All pictures will be the same across Entries for all 4 girls, so no need to look at it all. Cheers and here's the Deets: **Standard Tent Equipment** Unit Type: -Mammoth Pro 120, 120x120x200cm Extraction: -390CFM Vivosun w/ inline variable speed control and carbon filter Intake: -390CFM Vivosun w/ inline variable speed control Circulation: -x2, 30cm tower fans (early propagation) -x2, 90cm tower fans (late propagation) -x2, Hurricane clip on fans (Throughout full Propagation) -x2, Computer fans for supplementary air flow at floor level (Used as needed) Heating (supplementary): -”Heat Bud” by Honeywell. 2 setting ceramic heater (lights off operation) Humidity: -1 Gallon Ultrasonic Cool Mist by “Crane” Misc. Material/Equipment: - Large Variety of pots of different sizes, both fabric and plastics. (Future plans for Air pots) -Ratchets, strapping, ties, cords, patch cords, splitters and power bars **Control Devices and Operation** Heating: -x1, InkBird “Plug and Play WiFi Smart Controller” (ITC-308 WiFi) automation for extraction/intake air exchanges and temp control. (Current cycle: 3min exchange every 15min) -x1, InkBird “WiFi Greenhouse Smart Thermostat” for supplementary heater on night cycles Humidity: -x1, InkBird “Plug and Play Humidity Controller” HTC-200-WiFi automation for cool mist humidifier. WiFi enabled for manual overrides. Monitoring: -x1, InkBird “IBS-M1-WiFi Gateway” Data and Device Hub -x1, InkBird “IBS-TH1” Humidity and Heat Reader w/ Probe (High/Middle/Centre reader) -x1, InkBird “IBS-TH1 Plus” Humidity and Heat reader w/ Probe (Low/Middle/Master reader) Lighting and Misc Controllers/Devices: -x3, Digital Titan timers -x4, indoor/outdoor Humidity and Temperature readers (Close Proxy devices) **Parameters and Monitoring (Vegetation)** -Humidity will be achieved through automation and will hold 60-70% RH Vegetation/ 40-50% RH Bloom -Heat (Day) will be achieved through automation, holding 24-26 degrees in Vegetation -Heat (Night) will be achieved through automation, holding 23-24 degrees in Vegetation -Circulation on 24/7 and adjusted as needed (Direction/Speed/Time) **Flowering Parameters will be achieved and set to run at 23-25 degrees (Day), 18-23 degrees (Night) and a humidity range of 35-55%, pending on stage of Bloom** Additional Notes -Dual 4x4 tent units are acclimated and automated, same as listed above. The only minor difference is the exhaust and Carbon Filter in the Spider Farmer unit, but each motor is 390-410CMF and will operate at the same air pressure. -New devices for acclimation and monitoring may be installed shortly. This may include a night vision camera (custom for grow applications) and/or mechanical/electrical interlocking between equipment/devices to ensure a smooth operating system. -Not shown in pictures/videos sent are two locations. One is where I prep and mix nutrient feedings and the other is a propagation tent for new specimens (Mammoth 90x60x60cm). -All devices and equipment are slaved off a Surge Protection Power Bar, rated for 1500W, with the Futur Vert build having a dedicated 15amp branch cct (Installed and tested by myself) That's honesty it. Just Copy/Pasted between entries and I will not be doing a germination entry. Below I'll just write in method quickly...then leave it at that. Cheers all!👋 **Germination Method** -No pre-soak, direct to moist paper towel -Wait until 3/4 to 1 inch tap root and move direct to soil medium -Roughly 24-36 hour until sown seeds pop through soil -It's that easy... Peace!