RQS CBD AutoFlower - multistrain

Following RQS auto guide : https://www.royalqueenseeds.com/blog-how-to-grow-autoflowering-cannabis-n83 WEEK 2: LATE SEEDLING STAGE #8 22.3. - #14 28.3. #8 22.3. - Canna PH- grow (and bloom) arrived today, mixed 6ml to 3liters and poured around the pots (hoping to get hum. up also) will see what it does and if the PH starts going down from the 7+ i can start adding smaller amounts. -Moved around the LEDlights (those have 'bout 2000LUX at plant level) so they are more along the tent walls. -Moved temp meter from lamp to plant levet (have now confirmed the lamps wont heat up too much under current air flow so its safe to stop monitoring heat source temps. -Removed the "glass" from 3in1 meter and the tape from the front, tested the luxes, still at few hundred, so i would guess the LUX meter in that cheap meter is BS!. Now the PH is way more visible in the camera when there is no screen reflection etc. Added pics of the luxes from android app, will receive the "real"meter possbl this week. -When i had tent door open and did the stuff mentioned above the temp dropped to about 13degrees, but now we are already back up at 23'c at plant level, so seems stat the current exh-fan rotation is good. -Plants emself have taken some sort of an growth spur 'cause just few days ago they seemed like they are not growing at all, and ow i can really see the difference and they are making next set of leafes, might be that the temps risen so they enjoy em self now way more - forgot to take new pics from the plants emself so will juts update pics from cam for now , at least there's been some change again. -Will try to remember take proper pics of the plants next time i visit the tent physically -Should remember to buy the "LST-wire" for training, would be good time to buy some eastern decorations fluffy wires. #9 23.3. -Noticed that the timelapse camera is getting thrown around as well as one LEDpanel, so went and tied em up to tent posts. -Added 1,5liters of water that had 6ml of PH- canna in it, and poured in to "middle corner" of every pot. -Tent was way more warm and moist inside then ever before, which is a good thing, im sure after the latest added water im getting there. -Ordered a RAM humidifier. And some nutes pack from bio-grow. -Updated "week2 timelapse" (Check 1st week for its timelapse) -Note to self: Take those damn "camera quality" plant pictures, you are supposed to...- #10 24.3. -Started small form of LST -Guess who forgot to take the closeup pictures... again... Well better luck next time :D -Added 5liter RAM humidifier, at lowest possible setting, so that the water would last longest -Added 1,5liters of water with BioBizz nutes that came today in mail, Alg-A-Mic, Root-Juice and Top-Max. -Added ScrOG, but obviously its now just tested that it fits and its hanging at the tent side. -Had to move the Fast Eddy a bit and make a "stand" for the humidifier. -Moved the other LED (2300lux) a bit further up, will have more effect when plants grow, and those can be had as a xtra lights. -Moved some wires around their sockets to get better fit for all connectors. -Adjusted the camera directions -Turned both fans to level 1 of 2 -exhaust fan still at about 50% timer on/off, that must been what caused the "wobbly"pictures in timelapse as the tent gained more vacuum inside which must have drawn in the walls a bit. #11 25.3. -Not sure if i did anything #12 26.3. -Water run out from humidifier -Added a pic of the day -Luxmeter arrived, didn't had time to install it yet, but tested and found working. #13 27.3. -Added Hydrometer -Filled humidifier -Poured 1liter of water with nutes -Added/moved LST's -Finally remembered to take the close up pics of the plants! wohoo. -After following the hums i think i might add exhaust flow as its also warmer outside so the tent can now take it #14 28.3. -Last day of #2 week -Did nothing, just watched em grow. -Water run out of hum. hum went from 65% to 45%