so you think light to high at 20 in 30% intensity

420luv
420luvstarted grow question 1mo ago
I asked ai on phone what cause they said could be light burn at that time had it at 18 in started 25% intensity end week worked up to 50% when seen yellowish raised light and lowered intensity 30% using city tap water to water every 3 days have no way check ph
Open
likes
Answer
MindFlowers68
MindFlowers68answered grow question 25d ago
This is why people should be not giving AI answers to "green balls"
likes
Complain
MindFlowers68
MindFlowers68answered grow question 25d ago
Absolutely not unless you're poor. I think the yellow showing up because of the lack of light it's not able to produce chlorophyll. Cannabis is one of the most photo intensive lights there is. They do not like shade. It really depends on how doubt in your environment is for instance below is correct but I'm running Hunter watt lights 12 inches away from my plants and they're loving it. It all depends on if you got your environment and nutrients dialed in.
likes
Complain
Organoman
Organomananswered grow question 1mo ago
Without seeing an actual picture of the issue, there is no way to give you any sort of meaningful advice. It is a bit like going to the doctor and saying "I don't feel well" then saying nothing further............the reasons are many and varied, so without seeing the actual condition of the leaves, this question can not be answered accurately. Light burn with a 100 watt light at 18 inches and 25% intensity is impossible............even at 50% intensity.
likes
Complain
00110001001001111O
00110001001001111Oanswered grow question 1mo ago
More than one thing can caulse yellowing (chlorosis). No picture, no details, so can't comment much on that. Light damage tends to be interveinal, if that helps? It will obviously start nearest the light, not lower or mid-level leaves. If it was slightly too much light, you'd see tighter-than-you-want node spacing leading up to the damage, too. If none of that sounds familiar, might be nutrition-caused. also, seem to be taking an inductive approach to watring.. you don't choose the volume nor the time between (for the most part, even though there is leeway). You give the volume of water necessary to complete the task, not some pre-ordained volume. You wait until there is enough dryback before re-irrigating even if it's not exactly what you expected or wanted. 1) fully saturate (10% runoff, religiously, if it is a soilless grow, and always fertigate soilless) 2) Wait for appropriate dryback -- easy to recognize from depth of dryness up top or weight of the pot. Does everyon ewater at the same amount of dryback? No, but you need some minimum amount to avoid risk. I like a more exaggerated wet-dry cycle early on to promote thicker roots. Then i can take advantage of more frequent, but still safe, fertigations (i'm in soilless).
1 like
Complain
00110001001001111O
00110001001001111Oanswered grow question 1mo ago
in a perfect world (light is properly sized), hanging distance is more about light distribution wall-to-wall... reduced hotspots and more even across canopy. There's a diminishing returns on raising the light to even the light distribution across canopy. Don't over do it, but 16-24" is gernally fine for LED grow lights. A quantum board probably benefits more from a few extra inches than a frame of LED strips, for example. You can go too high... any light meter can help there... you don't want the overall average reading across canopy dipping except in extreme cases of a very over-powered light. Due to inverse square law (how light spreads out over distance), A few more watts and a little more height can provide greater light penetration, too. Whether or not that is worth the added costs depends on the context.... there's no one-size-fits-all answer here to do it "right" ... you need to understand how it works and adapt a strategey to your local variables. There's more than one way to skin this cat. ultimately you simply observe the growth pattern exhibited by the plant and adjust accordingly. That is your guage that takes all the factors into consideration - temperature, RH %, and atmospheric CO2. The more ideal those 3 factors are, the more light the plant can absorb per day. Seedlings take a bit more trial and error.. take some notes about what you do and refine the process until it's foolproof. They need less, initially, but will need more over time. Again, growth pattern tells you all you need to know... too stretchy? Needed more light. Too tight? Needed less light. Assuming you know what "full strength" is relative to a healty, mature vegetative plant, about 1/3rd of that is a good start. That doesn't mean 30% on your light... that is relative to how much you can give a mature plant in the climate you provide..
2 likes
Complain
The_7_Club
The_7_Clubanswered grow question 1mo ago
Use the manufacturer's recommendations and observe.
1 like
Complain