The Grow Awards 2026 🏆
Likes
Comments
Share
@Hashy
Follow
Week 6 Light cycle=18/6 Light Power=120w 50% Extractor controller settings High temp= 25c Low temp= c Temp step=0c High Rh= 56% Low Rh= % Rh step=0% Speed max=8 Speed min=2 Smart controller settings (during lights on). Lights on=06.00am Radiator on= below 21c Radiator off= above 22c Smart controller settings (during lights off). Lights off=00.00am Radiator on= below 18c Radiator off= above 19c VPD aim=0.6-1.4 DLI aim=35-40 EC aim=1.9 PH aim=6.2 Fri 26/1/24 #1 (Day 36) 📋 defoliate lower leaves that hardly get any light. Sat 27/1/24 #1 (Day 37) 📋 H=42cm D=39cm DLI=32.5 Raised light about 10cm Increased light power to 140w H=42cm D=49cm DLI=30.1 Sun 28/1/24 I have decided today is going to be the last day of veg before I flip to flower. Lights will have come on today at 6.00am and go off at 10.00pm, they will get 14hrs light today and tomorrow will be day 1 of 12/12. 💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧 Method= automatic Feed=Veg nutes. Neutralise=0.1ml/L Silicon=1.0ml/L Calmag=1.0ml/L Terra grow=4.0ml/L Roots=0.2ml/L Easy Ph down=0.125ml/L Ec= 2.05 PH=6.1/6.3 Time start=12.00pm Finish time=13.45pm (11×5 minute runs with 5 minute gaps) Total flow rate=181ml/min Flow rate per plant=45ml/min. Total volume made=12L Total volume left=2L Total volume used=10L Volume per plant=2.5L (Est) Runoff. Total runoff=1L Ec=2.7 PH=6.1/6.3 💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧 #1 (Day 38) 📋 With no information for flower time I'm going to have to guess she will be finished in 45-60 days. I removed quite a few lower nodes that probably won't break through the canopy, they where ideal candidates for clones. Light cycle=12/12 Light Power=140w 58% Extractor controller settings High temp= 25c Low temp= c Temp step=0c High Rh= 56% Low Rh= % Rh step=0% Speed max=8 Speed min=2 Smart controller settings (during lights on). Lights on=10.01-21.59 Radiator on= below 21.5c Radiator off= above 22.5c Smart controller settings (during lights off). Lights off=22.00-10.00 Radiator on= below 18c Radiator off= above 19c Mon 29/1/24 Lights on at 10.00am off at 22.00pm #1 (Day 39)(Day 1 flower) 📋 H=45cm D=46cm DLI=23.1 At 9.00pm increased light to 150w H=45cm D=46cm DLI=24.0 Tue 30/1/24 #1 (Day 40)(Day 2 flower) 📋 Wed 31/1/24 #1 (Day 41)(Day 3 flower) 📋 H=48cm D=43cm DLI=28.4 🚿 foliar sprayed (Sumo Boost 2ml/L). Thur 1/2/24 💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧 Method= automatic Feed=water Neutralise=0.1ml/L Roots=0.2ml/L Easy Ph down=0.ml/L Ec=0.2 PH=6.6/6.6 Time start=12.00pm Finish time=13.45pm (11×5 minute runs with 5 minute gaps) Total flow rate=181ml/min Flow rate per plant=45ml/min. Total volume made=14L Total volume left=4L Total volume used=10L Volume per plant=2.5L (Est) Runoff. Total runoff=1L Ec=2.0 PH=6.1/6.2 💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧💧 #1 (Day 42)(Day 4 flower)**** 📋 H=50cm D=41cm DLI=29.0 Lifted light and increasd power to 196w. H=50cm D=50cm DLI=29.5 She is doing great, has a nice height and shape to her. No problems still. She has been under 12/12 for majority of the week. Back soon. Take it easy.
Likes
33
Share
@AshBrand
Follow
This strain gave us no problems, very simple to grow! The plants both stayed small and bushy until flower, then they took off. We will be back to adjust the weight and add more comments. 8/14/21 - The buds are done curing and it’s 🔥 Smooth and flavorful 💨 We finally smoked it and couldn’t finish a joint lol. It’s a lot stronger than we anticipated. I love indica strains and this is now one of my favorites. Next up we have 2 Lemon Kush and 2 Gelato growing outdoors as a side project in between indoor LED grows. Blueberry from seedsman was so simple to grow. We messed up on a few things but we got plenty of nice buds and made 2lbs of butter for edibles. -FIN-
Likes
12
Share
@Aleks555
Follow
🏆 Eternity Grow Cup 2025: Plagron and Zamnesia 🏆 Strain: Runtz - Zamnesia Seeds Our girl is doing great! It's day 43 since sprouting, and 13 days since we switched the light to 12/12. She's grown significantly, with many branches stretching upwards. Given how many there were, I decided to trim her and removed about 10 thick and thin branches. I’m not sure how this will affect her, but I'm hoping to get fewer colas, though thicker and denser ones. We don’t waste anything from the pruning. The leaves that we cut off are frozen, then crushed in a blender. We mix the resulting mass with water, let it sit, and then water the plant with this solution. Additionally, we finely chop the leaves and mix them into the top layer of the soil, a practice called mulching. This way, we recycle everything and make full use of the plant material.
Likes
212
Share
Likes
10
Share
Week 11 – Harvest begins 🍂 This week marked the beginning of the harvest! Four plants have already been chopped and are now drying in the fridge at 5–9°C for a slow dry. Early testers are already showing strong effects and surprisingly good taste, even before a proper cure. The rest of the plants definitely need another week to fully ripen. The Mimosa Orange Punch is stealing the show with its incredibly sweet and fruity aroma – you can smell it from a distance! As for the Fast Buds autos, they’re seriously impressive. As you can see in the photos, they’re stacking beautifully, with tight buds and strong sativa traits – genetics are on point. Can’t wait to see how they finish! The grow is in its final stretch, and things are looking and smelling amazing.
Likes
5
Share
@Chupus
Follow
the first steps. I put it in a glass of water , later I will transfer it to paper towels . as practice shows, the method is working
Likes
29
Share
@TightNugs
Follow
Starting to pack a bit of weight now,no problems,steadily feeding.She was only 7 days in veg so happy with the progress.All good 🤞🍁
Likes
9
Share
Using some Neem oil and hydrogen peroxide ONLY ON MEDIUM (since I'm in flower), to get rid of these dumb fungus gnats I think they are the reason for the brown spots forming on the leaves. Installed a trellis this week to help spread out the canopy and improve airflow, however when I did this my dumbass accidentally snapped one of the colas, luckily I think it'll be ok because it seems to have only snapped the outer skin layer on only one side of that stem (I wrapped a piece of duct tape around the little snap to help secure it). This week went well I think I've got the fungus gnats under control, the stem I partially snapped still looks to be completely healthy and growing well so no complaints here successful 2nd week of flower👍🏾
Processing
Likes
5
Share
We are on week two of flowering and the ladies are loving it .. we defoliated and pulled some branches around increasing air movement and light penetration.. The cheese has been a little picky .. lighter on the nutes and doesn't like training very well..The team @seedsmen seeds have bomb genetics and I can't wait to stArt my next seedsman diary sooo good ..keep an eye out for week three ..
Likes
7
Share
I will b running the SHERBCAKE again to dial her in properly took a lot clones of her so I can’t wait to run her again terps of her is dessert and fuely 🍰⛽️ seeds made by k1 kreationz
Likes
4
Share
Likes
17
Share
@Reyden
Follow
La Auto Purple OG Punch sta andando bene ed entra nella seconda settimana di fioritura, alta 60 cm, e cresce a 12 ore insieme alle altre…vediamo come imposterà i suoi rami, per ora sembra che gli ho dato pochi nutrienti e non contando il suo fabbisogno di autofiorente che effettivamente è diverso dalle foto periodiche…però dopo tutto non sembra male e anzi penso proprio che riuscirà a stupirmi
Likes
114
Share
@Natrona
Follow
This week has been rainy so the outside girls only got watered and fed once. With all the rain we've had, all the girls grew a bit. I top dressed all girls with Bloomin Soil from Elm Dirt. Lemon Cake is now 48 inches and stacking nicely. Happy girl means happy mom.
Likes
16
Share
Final Report: Grow: The plants has grown very beautiful and healty without pests and diseases. They grown bushy and with medium height during all the life cycle. I had try to use LST in third veg week but i did't made correctly and after that i dicided to return to grown normally without any particolar tecnique. I used a littel more fertilizer then mine usual and that made the plants grown fast with only a littel bit of leaf margin burn which I solved by decreasing the quantity. In the first two weeks of flowering stage the plants started grow not to very tall (except for one) and the number of the branches increase, in this phase i only defoliated when the fan leaves turn yellow in late stage. During all flowering stage the flowers grown but they remained very soft, they turned dense and bigger in the last weeks and this time i waited until almost all of them were mature before harvest the plants(I waited a littel more respect OG Kush CBD). I changed the taller plant from one grow room to another(in the sixth week) when she became too high and she couldn't stay more in the smaller grow box(nothing changed in the enviroment between the two boxes). Equipment and grow box: The enviorment of grow box has been optimized every stage with the right temperature, umidity and air flow. Vegetative temp/umidity --> 23-29 °C/45-55% Flowering temp/umidity --> 20-26 °C/40-50% The air flow was created by two pc fans and one big fan. Harvest: This time the plants were full of dense buds but the lower branches had many fluffy flowers(i used them to make some hash) but the result not change too much . The result of this grow is amezing compared to my old expiriences. I harvested the flower and i made a fast curing process after i washed the crop and i let them to dry with a fan on it. After five days a take the branches which were to dry and i did the final trimmig before put all the harvest in a open jar for finishing to dry. I collected all the leaves, fluffy buds and trimming scraps in a bag and i let them dry. I harvested the taller plant before the other two because she had matured earlier(with the OG Kush ladies). Later i put the bag in the freezer and when i collect and dried all the scraps from OG Kush and Dandoverde Haze i did some Ice-O-Lator hash. I used 250g of trimming stuff and i made 11.50 g of hash, I had use a set of 5 bag and i take the resin from the 160µ - 120µ - 73µ- 25µ bags. I pressed all the resin in a great block of tasty strong hash. Always better every time 😊💪 Total harvest ---> 126g only of dense buds and 11.50g of hash.
Likes
9
Share
Well it's safe to say the foop will work with legit strong good bacteria! But the focus has to be on the root health when it comes to how much food you can add and still maintain healthy roots. But the game changer for me has been switching to a air stone, 1st and for most. The recirculation pump suggested by foop when running foop in dwc ran the solution temps into the high 70's around 77°F and anything over 75°F has been where root rot sets in for me. Even switched to way smaller recirculation pump with same results. So switching to running a air stone was big! But also found that running one Vivosun 317GPH Air Pump 15W split to 4 plants was not enough air for the roots to be happy in the foop plants. So I moved to a 2nd air pump, same size per tent. So now it's only split to 2 plants on the foop plants. And that made a big difference! But found after a few weeks that I had to bleed a slight amount of air off because there soo much extra air the humidity was sky rocketing in the tent to high 80%. So there's a sweet spot where they get extra air but not soo much that the humidity is affected. But the 2nd most beneficial thing I've done is start running Orca. It has made such a huge difference. I think I need to go up with how much I'm using or find something that works even better if possible. But the sweet spot now is 8 to 9ml total of each foop veg/bloom 1,2 and sweener. When I go to 12ml with foop 1,2 the roots take a noticeable hit. So idk how I would go to the recommended 20 to 50ml per gallon as suggested on the foop grow chart. I tried going to 10ml foop 1,2 on this one but the roots didn't like it and it shows they have never turned back to a blonde or white color again Currently running around 6 to 10ml orca total per feeding. And adding 2 to 4ml when I add foop 1,2 mid week and got happy roots! Also the Seaweed extract has made a difference in the smell the plant puts off. Last few grows have been really muted with smells and this grow I actually get hit in the face when entering grow room. So has made a difference forsure!! I'm soo excited!! Currently has issues getting the humidity below 55% in the grow room. I was running 6 damprids 1 on intake(outside tent) to tent, one on inside of tent(at inlet) and 1 on exhaust(outside tent) for 2x4 tent and 2 hanging at 4x4 tent exhaust and one hanging by ac unit. That brought it down like 5% over all but now I'm running 12 damprids to try and get the room down humidity in the mid 40's. We will see. The house runs a swamp cooler and that basically makes the whole house pressurized. So even tho I sealed the grooe room door and the window with ac the best i can. it's a uphill battle! Once swamp cooler comes on the humidity in grow room climbs like 10%. So here's to hoping🤞🤞🤞🤞 6/25 added 2L 6/26 added 1.5L, 10ml Seaweed extract, 4ml orca, 4ml foop bloom 1&2, 4ml foop sweener, 3ml cal mag 6/28 added 2L 6/29 added 1.5L 6/30 added 1L, 20ml Seaweed extract 7/1 refreshed, gave 20ml hydroguard, 15ml orca, 25ml Seaweed extract, 9ml foop bloom 1&2. 10ml foop sweener, 6.5ml cal mag Records kept here: https://1drv.ms/x/c/fa218bbdbbfbd064/EelXI2vd0VdDoZBL4JvZ6xMB7lSyddsPGq8FdBGttRAjgg?e=rY8meL 👋👋👋 Hello, Thanks for checking out my grow!! Please like and follow I really appreciate it!🤟 Please feel free to leave questions and comments below!!👇 I really appreciate all advice!!! Check out my Instagram, you can message me there too! And check out my youtube for more content! Mistakes were made, but what better way then to live it and learn it yourself!!!!
Likes
40
Share
@Tazard
Follow
I could tell within a week of flower that she would probably be a monster. She was always given priority for space and light. When I realized that she was covering 7sqft I realized that she didn’t have enough light and I moved 3 more LED’s to her so as to not be light limited for harvest. Based on 600g/m2 I needed at least 400w for her. I managed to get almost 670g/m2!
Likes
85
Share
Creo que no ha sido buena idea esa defoliacion que la he hecho, pero bueno, se va a recuperar, solo que voy a perder 1 semana seguramente. Riego por inundacion. 📅 Dia 36: Riego por inundacion con nutrientes. 📅 Dia 37: Descanso 📅 Dia 38: Descanso ya que regué demasiado, voy a bajar la cantidad de agua que aplico. 📅 Dia 39: Descanso 📅 Dia 40: Riego con muy poca agua con nutrientes 📅 Dia 41: 📅 Dia 42:
Likes
30
Share
@Grey_Wolf
Follow
Northern Lights Outdoors Expert seeds Northern lights 10th February 2022 She is developing really really well and smells great 😍 The bio bloom is working great 👊 Cheers for stopping by to read my update 👍
Likes
39
Share
Strange week for the plants as I switch in Hygrozyme Enzyme to help with the roots. A lot of dead tissue being consumed by beneficial microbes and fungi. PH rise more than 10 fold every 24 hours while EC levels rise by a point or two. The old roots are dying and being consumed new while bright, crisp, white roots are appearing. New growth is vigorous and the plants seem to enjoy the transition as hard as it is. Dinamed Plus from Dinafem Seeds (1) and Blueberry Headband (1)from Humboldt Seeds. https://www.dinafem.org/en/dinamed-cbd-plus/ https://www.humboldtseeds.net/en/blueberry-headband/ Lighting https://www.horticulturelightinggroup.ca/products/260w-qb-v2-led-kit DWC Nutients https://generalhydroponics.com/floraseries FloraGro 1 ml/l FloraBloom .5 ml/l FloraMicro 1 ml/l Diamond Nectar: N/A https://generalhydroponics.com/diamond-nectar Cal Mag: 2 ml/l https://generalhydroponics.com/calimagic SuperThrive: .5 ml/l https://superthrive.com/ https://hylineproducts.com/products/hygrozyme/#one Grozyme: 2.5 ml/ltr Tarantula https://www.advancednutrients.com/products/tarantula/ Epsom salts Tarantula Tea 4 liters RO or tap water 5 ml (1 tsp) organic sulphur free molasses 5 ml Alaskan Organic grow fertilizer (or something comparable) 5 ml Alaskan bloom fertilizer (or something comparable) 5 ml Seaweed or kelp fertilizer 2-4 ml Advanced Nutrients Tarantula