By continuing to use the website or clicking Accept you consent to our cookies and personal data policy and confirm that you are at least 18 year old. For details please see Privacy Policy and Terms
Accept
Likes
Comments
Share
@DogDoctorOfficial
Follow
Hey fellow green thumbs! 🌿💚 We’ve just wrapped up the fifth week of flowering with our Auto Fast Pete and Auto Northern Dragon Fuel from Super Sativa Seed Club. This week has been all about resilience and adaptation as our plants continue to push through the challenges. Let’s dive into the details!
🌟 Week 9 (Fifth Week of Flower) Progress:
Day 57-59: Bud Development and Resilience
• Auto Fast Pete: Despite the ongoing stress and burned leaves, Pete’s buds are continuing to bulk up. The aroma is rich and potent, filling the grow room with a delightful scent. The resilience of this plant is truly remarkable. 🌿🌸
• Auto Northern Dragon Fuel: Dragon Fuel is also showing strong bud development, with sticky, dense flowers. The burned leaves persist, but the plant’s overall vigor remains impressive. 🌱✨
Day 60-62: Growing with the Flow
• Nutrient Strategy: Continuing with the adjusted nutrient regimen, including increased CalMag to support the plants through the stress. Monitoring the plants closely to see how they respond to these adjustments. 🌿
• Reservoir Details:
• TDS: 450
• Temperature: 18°C
• pH: 6.2
• Environmental Conditions:
• Temperature: 31°C
• Humidity: 51%
Maintaining these conditions to optimize bud development and plant health. 🌡️💧
Day 63: Observing and Embracing the Journey
• Auto Fast Pete: The buds are continuing to grow and mature. The plant’s resilience in the face of stress is truly inspiring. 🌿🌼
• Auto Northern Dragon Fuel: The bud sites are dense and sticky, and the plant is showing incredible strength. Despite the burned leaves, the flowers are developing beautifully. 🌱🌟
🌟 Care Tips:
• Light: Maintaining the 12/12 light schedule. The plants are adapting to this schedule, and we’re keeping a close eye on their response. 💡
• Autopot System: The Autopot system ensures a steady water supply, reducing the need for frequent manual watering. This system is great for maintaining consistent soil moisture, which is crucial during the flowering phase. 🌊
• Nutrient Monitoring: Continuing with the increased CalMag dose to address deficiencies. Keeping an eye on the reservoir’s TDS and pH levels to ensure the plants receive the right amount of nutrients and minerals. 🌿
• Environment Control: Maintaining a stable temperature of 31°C and humidity around 51% to create the perfect conditions for flowering. Adjusting airflow and positioning to optimize plant health. 🌡️💧
🌟 Genetics Spotlight:
Auto Fast Pete:
• Characteristics: Rapid bud development, strong structure, early resin production, but showing signs of stress and possible nutrient deficiencies. This strain is still pushing through with impressive bud bulk.
• Future Expectations: Continued bud swelling and resin production. Monitoring nutrient adjustments closely to ensure a healthy finish.
Auto Northern Dragon Fuel:
• Characteristics: Robust structure, dense bud sites, resilience, but also showing stress signs and possible CalMag deficiency. The buds are still developing beautifully.
• Future Expectations: Significant bud growth and increased resin production. Close monitoring and adjustments will support a strong finish.
🌍🌿 Fun Fact:
Did you know? 🌿✨ Plants are incredibly resilient and can adapt to a variety of stressors. This resilience is especially important during the flowering phase when the plants are focusing their energy on bud production.
For all the in-depth action and detailed explanations, head over to my YouTube channel! 🎥✨ I’m sharing all the tips, tricks, and step-by-step guides to help you get the best results from your grow. This week has been particularly challenging and exciting, and there’s so much more to explore and learn together!
👉 Join me on YouTube Link in my profile 👈
🌟 Conclusion:
Week 9 marks the fifth week of flowering, with both Auto Fast Pete and Auto Northern Dragon Fuel showing remarkable progress despite some stress and deficiencies. The buds are developing beautifully, and with careful monitoring and adjustments, we’re set for a promising harvest.
Stay tuned for Week 10, and happy growing! 🌿💚✨
#SuperSativaSeedClub #Week9Report #FastPete #NorthernDragonFuel #PlantMagic #GardeningJoy #NatureLovers #PlantPower #InspireGrow #YouTubeJourney
Germination method 🌱 @thecannakan
Genetics @supersativaseedclub_official
Nutrition
@aptusholland 🌿
@aptus_world 🌎
@aptus_es 🌍
@aptusbrasil 🌱
@aptus_thailand 🌿
@aptus_portugal 🌳
@aptususa_official 🍀
@aptusplanttechnz 🌺
@aptusplanttechaus 🍃
Ambient controls🎮
@trolmaster.eu @trolmaster.eu.support @trolmaster.support @trolmaster.agro
Soil @promix_growers_eur @promix_cannabis
LED - @lumatekeu
Watering- @autopot_usa @autopot_global
Love and attention- @dogdoctorofficial
As always thank you all for stopping by, for the love and for it all , this journey of mine wold just not be the same without you guys, the love and support is very much appreciated and i fell honored and so joyful with you all in my life 🙏
With true love comes happiness 💚🙏 Always believe in your self and always do things expecting nothing and with an open heart , be a giver and the universe will give back to you in ways you could not even imagine so 💚
More info and complete updates from all my adventures can be found ⬆️link in the profile description ⬆️
Friendly reminder all you see here is pure research and for educational purposes only
💚Growers Love To you All 💚
Discount Codes :
@thecannakan DOGDOCTOR 15% off
@theneutralizer PORKIT5-DOG 15% off
@kannabiaglobal DOGDOCTOR 30% off
@seedsmangenetics DOGDOCTOR 10%off
@terpyz.mutant.genetics DOCTOR 15% off
Likes
31
Share
@DudeGrowsWeed
Follow
Dropped RQS Diesel Automatic this week, she has not sprouted out of the soil yet, but its only been 4 days. I expect her to pop in the next 24-48 hours. I'll add new pics once she sprouts.
Planning a slightly different strategy with this girl. no HST, only LST, and FIM'ing instead of topping. Looking forward to watching what happens.
She is front-center in the group pics.
My Perpetual Harvest strategy…. Originally my plan was to start 2 seeds each month, but had some seeds from one breeder that did not germinate early in my rotation. Ultimately, this caused single seeds to pop and messed up my 2 at a time plans. But, that seemed to work out OK, because now I think starting one seed every 3 weeks is a better strategy. This should provide me with 4-5 plants at a time, instead of 6. By the way, I never had any germination problems with seeds from other breeders. (I don’t want to bad mouth any breeders, but the seeds that didn’t germinate came from a popular breeder/advertiser that is most commonly known by 4 letters).
Plants get fed once weekly on weekends. Seedlings get water only. Plants in vegetation get water and Recharge. Flowering plants get water, Recharge and Big Bloom (Fox Farm). Feeding is done using 2 gallon watering can. Any additional waterings during the week are given on an as needed basis per plant. I lift the plants to help determine which plants are more dry (lighter) and provide water any plants via water bottles and watering spikes.
I also rotate each plant 90 degrees every day in an effort to make sure the plants get equal lighting from all sides. I rotate the plant in place by turning the pot 90 degrees (I am not rearranging the layout of the plants in the tent on a daily basis).
The soil is an ‘organic super soil’ I mixed myself using organic top soil, organic potting soil, organic compost, organic peat moss, organic perlite, organic vermiculite, lime, epsom salt, expanded clay pellets and Jobe’s organic fast start. I am also recycling my soil and water with Recharge when using recycled soil.
For plant training I have tried a variety of things, but my plans here are to do LST bending only, no HST this time. Around 3 week I'll do a FIM cut/pinch once there are 4-5 nodes established. I will also be doing some defoliation around the 3rd week of flowering. I have been doing HST bending and having good results, but think the HST may be causing the plants to take longer to harvest. I hope LST only will help increase harvests while getting me to harvest sooner.
Setup:
1- Grow Tent 24”x48”x72”
2- Viparspectra 300W LED’s (1-V300 & 1-R300)
1- Hanging 100w CFL (26w actual)
1- Carbon Filter w/ 190cfm Fan & 4” ducts
1- 6” clip-on fan
1- 700w electric heater - oil filled radiator (in front of air intake behind tent)
Likes
4
Share
@DaisyNabis
Follow
preventivo de la semana al dia, desintale humificador para preparar a mis bellas para su trasplante a maceta definitiva, esta oportunidad no hare podas bajas solo algunas defoliacion
Processing
Likes
15
Share
@Rangi_Kijani
Follow
I harvested 24 cuttings from the White Shark mom this week, which was the first time she donated! She recovered fully within a few hours. Some ongoing maintenance pruning/training on deck for later this week.
The 2 new moms (XXL & 8 Ball) are looking beautiful. I’ll be topping them soon to start working on structure.
Likes
11
Share
@TheThiccBud
Follow
sooooo... I have now harvested the plants and they looks so pretty 😍😌 I'm really proud of myself to have produced such THICC BUDS!!! 😅😍 and the smell is so awsome 😵 this strain is a 11 from 10 👌 a realy big Thanks to Royal Queen Seeds for this 2 awsome strains 💪 A detailed rating comes after drying with a detailed score board 😄
Likes
18
Share
@VI_Cannabis
Follow
June 7 - We ordered some new lights last week, they are 240w kingbrite samsung lm310h with uv/ir, 3000k, and meanwell drivers.
We setup the new room and moved the girls into there. After a bit of LST and a watering (with nutrients) at roughly 7ph, they were ready to go under the 2 new lights and the same SF-1000 we have been using in this grow.
The new room is a 12 ft enclosed trailer. I moved everything from the small tent into this. I put clear poly on the walls, floor and ceiling. I put poly on the shelf I am going to be keeping in there as well. I bought 50ft of 6mm mylar and lined the floors, roof and sides with it. I plan to get some reflective tape to seal everything and to cover the wood. I did not get much of a chance to watch temp's today as they it was later in the evening after all was said and done. The inline fan blowing in air from outside.
June 8 -
9 AM i checked the plants, they were at 25.2 and 50% RH. Late through the day I had checked and we had gotten up to around 32 degrees. So I moved the inline fan to the closer vent, hooked up to that, and had the air blowing out of the trailer with the inline fan sucking it from above the lights.
I then added oscillating fan and had it blowing air on the left side of the room so it would somewhat circulate once I closed the doors. I then checked at about 9pm and we were at 22 degrees. Definitely noticed a decent amount of growth already. I have the lights on a 22/2 cycle as I was worried about the heat at night time.
June 9 -
Some great growth from the girls, still having problems controlling the temps in the afternoon. I decided to prop the door open a bit to have a constant breeze throughout the day while I am at work. Decided to do some more LST and also a bit of defoliation. I took about 25% of the leaf's that were blocking the new growth as it was getting a bit bunched up. I was then told the leaf's are almost solar panels for them. So from now on I will be trying to just do some tucking unless needed. The leaf's I removed were most of the damaged leaf's, I am not to sure if that makes much of a difference. I gave them a watering with only water as there is a potential I am getting a bit of a nutrient buildup along with the PH problem. Or potentially the reason for the ph problem is nutrient buildup. After watering with A PH of 7 I got some run off and tested it. The smaller plant gave me a PH of about 5.5 where the bigger one is around 5.0.
June 10 -
Plants are looking happy and showing tons of growth. Seems to be trying to stretch outwards. Not a ton of sign of PH issues showing so potentially getting it under control. Still a bit of damage to previous leaf's but it is what it is! The last few days I have been leaving the door open a bit in order to keep the temps down. I decided to test something and turn the lights off (automatically) at 11AM and back on at 5PM so light schedule has now changed to 18/6 and it seems I may have figured out the issue. We haven't had lots of sun the last couple days so it hasn't been to hard and I have yet to know if it truly fixed the heat issue for now. (I will be looking into a ac unit as well since it typically gets to around 30-35 around here.
June 11 - Pulled some of the branches back down and added a few more LST spots. Seems we have a good amount of growth from the smaller plant out of the 2 topped spots. Unfortunately it looks like I fucked up on the bigger plant and only one of the nodes seems to have new growth. I will continue to monitor that but I think I cut the node to low and also to soon. Other then that, the girls are doing great. They seem to be absolutely loving these new lights. I gave them some nutrient water today as well. roughly 3L each. They seem to be A hell of A lot more thirsty under these new lights.
June 12 - The girls are doing great , they are still just doing growing away. Lots of progress everyday. I am going to be getting a go-pro so I can set-up a time-lapse for the rest of this grow. I received my new inline fan, I got A ac infinity CLOUDLINE T4 with the temperature humidity controller. I am going to be having one fan pushing fresh air in and one fan pulling out the hot air. I will be doing that tomorrow since I have to work today.
June 13 - I ordered another 50ft of mylar and that showed up today. I have decided to remove the shelf and add another 3+ feet to the grow space. So today I installed more poly, mylar, the ac infinity fan. I have it set-up to pump in air if it gets to warm. I am thinking of switching it to the output that way if it gets to hot or to humid I can have that air pulled out of the trailer. Right now my other inline fan is the outtake and I just have it set on full. Overall I think everything is set-up a bit better and more accessible. I will be putting my 2x2 tent in there at the left of the doors so I can have a veg room when these 2 are in flower. I plan to have 4 in veg and 4 in flower for the next grow. Still waiting on JOTI seeds, ordered 3 weeks ago and still have not been shipped. I will be getting those going the moment they arrive.
The girls seem to be happy still, did a bit more LST to try to keep everything even, mainly I'm just pulling down on the spots I already have tie wire on.
Likes
14
Share
@Mr_nugs_lover_David
Follow
This lady has been Transplanted on day 39 since she was planted (may 10th) and I've prepared the 15L pot with the complete line of biotabs using 2 spoons of startrex for every 5L, sprinkled a couple of grams of mycotrex on the transplant hole before putting the plant and then I added 3 slow release tabs one biotab for every 5L of soil, so that's why in this case I added 3, after the Transplant was done I immediately watered the plant with 1ml/L of orgatrex and 1g/L of bactrex, I hope you guys enjoy my work this season!!
Likes
3
Share
@TheBudWhisperer
Follow
End of the 3rd week of transition and plants are still lazy as hell getting to flower. There’s minor pistoling but no cotton balls at all. They’re slow all around.
We ended up culling down to a 50/50 split of males and females and now it’s just a question of whether or not the females actually flower. We’ll see I guess… still wait’n….
Likes
48
Share
@McBubatz
Follow
14. Woche, P1 fällt morgen, die ist soweit gut denke ich (ca. 20% aufwärts Bernstein Trichome).
P2 braucht leider noch ca. 1 woche länger.
93. Tag ist für P1 das Ende, sie wurde heute vorgetrimmt und zum trocknen aufgehängt.
Ergebnisse gibt es wenn die P2 auch geerntet wird, denke nächste Woche um die Zeit.
Aber eins kann ich euch versichern, is mit Abstand die schwerste die ich ist jetzt hatte😊🍀🍀.
Gebt euch auch mal wie viele Trichome die gute produziert hat, Duft is noch sehr pflanzlich, Blüten sind ziemlich fest gewesen hoffe das es nach dem trocknen noch so ist. Alles in allem super Run.
Hoffentlich is die gute bei den Top 10 das wäre ein träumchen, wobei ich es wirklich jedem gönne zu gewinnen und bei soviel starker Konkurrenz geht ich wahrscheinlich unter.
ABER was ein geiler Contest trotzdem, hier ein dickes fettes Dankeschön an Zamnesia und Plagron für die Möglichkeit hier überhaupt mitmachen zu dürfen 🙏💙💜
98. Tag , werd die gute am Samstag/Sonntag je nachdem wie ich Zeit finde, umlegen und zum trocknen aufhängen.
Likes
39
Share
@DreamIT
Follow
Not one of the fastest autoflowers out there, but with excellent results. You plant the seed, water every now and then and wait: p With white widow you are never wrong
Likes
1
Share
@Nino03
Follow
My new 600 white ballast came in, so I'm back to 2 600 watt lights, happy about that. I did a little Platt training on my clones to get them to bush out so they won't grow so tall next time. Cleaned up all the small popcorn shoots underneath.
That wasn't getting any light.
Likes
19
Share
@JeyGanesha
Follow
Siamo all'ultima settimana.il flush è iniziato da un paio di giorni💪👍🕉️10/15 giorni ancora e via......in questi ultimi giorni sta buttando fuori dei profumi intensi e vedo che sta tirando fuori dei colori favolosi. ... non vedo l'ora di assaggiarla Pre sentire se funziona bene come terapia😉💪💚💛👍
Likes
13
Share
@tresplantes
Follow
Its Day 31 the last day of flower all plants are more than ready for 12/12
I will increase the light on the First flower Day to 100% to minimize stretch
Likes
6
Share
@GoldenWeedGrower
Follow
Legend
Timestamp: 📅
EC - pH: ⚗️
Temp - Hum: 🌡️
Water: 🌊
Food: 🍗
pH Correction: 💧
Actions: 💼
Thoughts: 🧠
Events: 🚀
Media: 🎬
D: DAY, G: GERMINATION, V: VEGETATIVE, B: BLOOMING, R: RIPENING, D: DRYING, C: CURING
______________
📅 D64/B27 - 18/06/24
⚗️ EC: 1.0 pH: 5.2
🌡️ T: 26°C H: 80%
🌊 FLUSH
🍗
💧
💼 FLUSH first day
🧠
🚀
🎬 1 TL video
______________
📅 D65/B28 - 19/06/24
⚗️ EC: 0.2 pH: 7
🌡️ T: 26°C H: 80%
🌊 FLUSH
🍗
💧
💼 FLUSH second day
🧠
🚀
🎬 1 TL video
______________
📅 D66/B29 - 20/06/24
⚗️ EC: 1 pH: 6.2
🌡️ T: 26°C H: 80%
🌊 15 L
🍗 CalMag - Bloom A-B - Bud Candy - B52 - Overdrive
💧
💼
🧠
🚀
🎬 1 TL video
______________
📅 D67/B30 - 21/06/24
⚗️ EC: 1 pH: 6
🌡️ T: 26°C H: 70%
🌊
🍗
💧
💼
🧠
🚀
🎬 1 TL video
______________
📅 D68/B31 - 22/06/24
⚗️ EC: 1 pH: 6
🌡️ T: 26°C H: 70%
🌊 15 L
🍗 CalMag - Bloom A-B - Bud Candy - B52 - Overdrive
💧
💼
🧠
🚀
🎬 1 TL video
______________
📅 D69/B32 - 23/06/24
⚗️ EC: 1 pH: 6
🌡️ T: 26°C H: 70%
🌊
🍗
💧
💼
🧠
🚀
🎬 1 TL video
______________
📅 D70/B33 - 24/06/24
⚗️ EC: 1 pH: 6
🌡️ T: 26°C H: 70%
🌊
🍗
💧
💼
🧠
🚀
🎬 1 TL video
Likes
12
Share
@SnarkyGoat
Follow
I wanted to title this weeks grow "How Big Are Your Balls? (root balls that is, lol)". I've been wanting to post pictures and video of the root balls for a while now, so today's the day! The temperature has been dropping here, so the plants are getting much less heat stress. In a couple of weeks the temperature should be down into the 60's and 70's during the day and all will be good.
Likes
6
Share
@growerfromnc
Follow
Staked down and moved light 12 inches away from plants ration of 1to1 gallons when feeding
Starting to see prer flower 🌼
There booming massive root balls these bitch chuncky
Likes
25
Share
@pifflestikkz
Follow
Day 58
30/08/24 Friday
Feed today using de-chlorinated tap water pH 6 with Plagron products.
Day 60
01/09/24 Sunday
De-chlorinated tap water pH 6 with calmag today.
Picture update ✌️💚
Day 62
03/09/24 Tuesday
