####Please do read the disclaimer in the first entry! 01/28/25 Short facts: - VPD @ 1.0 but normaly it doesn't get better than 0.9 - Light @80% so most leaves are exposed to 500 - 960 ppfd - Success with the colloidal silver --------------------------------------------------------------------------------- Finally, the attempts to spray her with colloidal silver were successful. Many pollen sacs are developing, and I hope they will be ready within a week. Buying a new spray was the right decision because, with the new one, it took less than two weeks for the pollen sacs to appear. However, the leaves are looking worse now—some are almost 70% dead. I still hope she will make it so the seeds can fully develop. I planted the Lemon Cherry Cookies much earlier than the other two plants to avoid pollinating Slurricane and 1:Walt. However, due to the delay, both are already in flower, so they will end up with some seeds. Maybe one of the crosses will turn out to be something special! 😂

All ok

Blue dream autos gone into full flower gsc is still in pre flower im liking how big they're getting tho Blue dreams not liking the strength of nutes dropped it back down to half strength hopefully she picks herself back up today

My first solo cup grow, didn’t do any style or technique like the traditional solo cup. I let it grow on its own and it grow more than I expected, I didn’t think the cup can sustain that huge plant but it did. But it didn’t do well in buds development but then again It was my fault. Overall, the grow was easy and interesting. Next stop: smoking!!! 😂

NOTES: Keeping pH at 5,8-5,9 through the entire Vegetation-phase. EC is now around 1,2 and i'm increasing it if needed. I'll be checking the levels regularly from this week since all of the hydroponic systems are now running. I'm going to add some ice cubes in to the nutrient tanks to cool nutrient solution a bit always when I remember to, even though temperatures haven't been an issue so far. Can't do any harm so why not I quess. I'm also adding a CO2-bag in to the tent above the plants. Also I'll begin training my plants this week by topping them. Day 22 (8.11.) Lights are set to 70%, water pumps are now on for 24/7 (EBB's drain water is on lowest setting possible to avoid drowning the roots) and pH is 5,8-5,9 / EC 1,2-1,3 on every hydroponic system. I topped all of my plants and cut off all of the lowest leafs with single tips and some of the small nodes starting from them. Day 23 (9.11.) pH-level keeps on raising so I'm gonna be measuring it pretty often. I'm correcting it by adding some pH- while filling up the nutrient tanks with small amounts of fresh nutrient solution at a time. Everything's going well and I can't wait to flower these! Day 24 (10.11.) Lights are now set to 80% power at 70-75cm height from the tops. I cut off the rest of the lowest nodes which I had left to some of the plants while topping them. I don't think they would get enough light when they are bigger. Day 25 (11.11.) Removed the lowest (three-pointed) leafs of each plant. Day 26 (12.11.) I moved the Led's a bit higher (now at ~90cm above plants) and set them up to full power. Plants are now around 11-14cm height and growing like crazy! Day 27 (13.11.) The growing has exploded and these plants are getting bigger and bigger. I'm going to defoliate them lightly and remove the lowest nodes so the plants have around 6 nodes each going forward, hopefully I'll get an even canopy. Day 28 (14.11.) I changed new nutrient solution in to the EBB-flood system which has the Ayahuasca's on it. I'm keeping the EC at around 1,3-1,4 and pH at 5,8-5,9 on every system. Also added small amount of Cal-Mag in to both NFTs.

At Day 25 I topped 3 of them. Tommorow i wil top the rest . By during LST one of the branch broke... so i taped it .. look 1 of pics.

Day 28 Flowering: The bud building continues. FFT#8 Is so sad to look at now in comparison. she is budding but so small it will be a shock to get a joint from her .lol FFT#9 Is looking like a real contender for yield champion this run. Her long forming colas are so good to look at close up and so neatly packed in too. She has many long donkey's to fill out now and with 5 weeks left to run, I think she will do well. She is smelling nice and fruity with a hint of fuel too now and beginning to push trichrome production too. Still cannot place her strain yet but one i will certainly be doing again when I find out. FFT#10 Has some very thick colas forming up and plenty of sugar leaves to cover in her abundant trichs. She is a great producer of frost already and I am convinced she has some cookie or wedding cake in her parentage ?. Her darker colour and wider leaves show her Indica leaning before her wider noded structure does. she smells a dangerous earthy spicey aroma now and i think she will give the Fft#9 a run for yield too. She did respond to the gentler lst I did with keeping her 5th but it has meant she kept saying more vertical than wide and flat. not an issue i am pleased to find out and I coukd possibly use more height in the next run I do with the autos lined up to do. I had hoped Fastbuds would have responded with a request to run their genetics but time ran out waiting and I needed to plan so went with another breeders autos offered. I do love fast buds and their genetics. Until next week ( or patience gives out and I update this weeks.lol) Be safe and well Growmies

Easy to grow, strong weed, but yield is low, so put a couple extra ;)

Week 3 and a repot is done and now in day 3. Finally it’s settling down after the repot, which was not pretty at all😂 Hope to get some massive plants this run 🌱 ________________________________________________________________________________________ Light from @MedicGrowLED 😎 NEO 780 LED🔥 780 Watt⚡️💥 PPF of 2184 μmol/s & 2.8 μmol/J🔥 Full Spectrum V1/F1 🌈 WiFi smart connection & Smart Aura Control 😱

Welcome growfessors to another episode of growfessor theatre! Week 2 begins in the 4x4 tent for these 4 ladies. The grow medium is still damp and heavy, so no feed yet this week. I will wait a few more days before feeding. Ladies look happy and healthy under the Mars-Hydro TSW2000 light. Thanks for stopping by growfessors, tune in next week for another episode 👽🌳💚

d14 Se las ve más pobladas, parece que no les ha causado mucho estrés por lo que han continuado creciendo y lo que yo quería, ahora las ramas laterales, reciben mejor la luz y están creciendo bien. Tienen buena estructura la mayoría, son bastante simétricas. Semillas a granel y ya veis la calidad que tienen, no son super estables porque no se parecen tanto entre ellas, pero no son malos ejemplares, en cuanto a estructura. Tenemos las plantas del fondo, la zona donde está dando el ventilador, y me he dado cuenta que esas plantas tienen algunas hojas medio amarillas y blanditas, parece ser que se han creado alguna bolsa de humedad, necesitaré un ventilador más para que no pasen estas cosas. También he mirado un poco algunas plantas y tienen lo que viene a ser la primera rama satélite, pues es muy fina y no ha crecido en altura para poder recibir luz, por lo tanto se cortarán estas ramas.ç PD: Si se ve una semilla germinada en una maceta, es una 1024 que se quedo en la tierra y parece que le cuesta mucho, pero que nunca se rinde. d15 Algunas tienen un callo bastante gordo en la unión de las ramas satélite. Se han cortado las ramas de abajo del todo, primeras satélite de algunas plantas ya que no les da la luz y no nos van a hacer falta.

** COST ** TO RUN - Used previous ⛺️ setup : 0.00USD - Monthly electricity : 36.73USD <-- other ladies sharing ⛺️ - 3 Gallon Fabric pot : 0.15USD - Bonsai wire : Apx. 0.03USD - Reused soil from last run : 0.00USD FOR NUTRIENTS - Jadam Microbial Solution : 0.00USD - Fermented Plant Juice : 0.00USD APPLYING - JMS : 30ml / 1 Litter - FPJ : 30ml / 1 litter TOTAL COST : 36.91USD Throughout the week, I give compost tea, and fermented plant juice once each ^^ Its almost time!! Trichrome are cloudy, but its hard to find amber Trichromes yet. According to Fastbuds she will be ready in 4 days ^^; Hope you guys have a wonderful day today ^^v *** Please Like, comment & share *** Highly appreciated -----/-----<@

Purple punch is nuts, super frosty. Even some fan leaves are covered with tricomes. I believe I will flush it very soon, maybe in the next watering. Gorilla punch beautiful plant with some purple nugs. They are getting really fat Mimosa cake still getting more and more white pistils and I hopping the nugs get fat 🙏🏼

On day 1 I did another light defoliation. The plants are progressing as expected. The only issue I'm dealing with is fungus gnats... ugh. I will keep applying BTI weekly until the population is under control. On day 3 the plants are putting out more pistils and seem to have stopped or slowed down their "stretch" phase. On day 4 I'm starting to see some trichomes forming on the sugar leaves, no smell that I can discern yet. I also changed out my reservoir and applied a BTI soil drench. On day 5 I adjusted the PH of my reservoir down to 6.1. I also purged my blumat system to make sure there are no clogs as my reservoir has fertilizer particles due to my water heater causing separation. I must keep the water heater on as I am growing in the northeast coming into the cold time of the year and can't have my reservoir freeze on me. On day 6 I adjusted the PH of my reservoir down to 6.1. On day 7 I adjusted PH in reservoir to 6.1.

💩Holy Crap Growmies , we are outdoors and in the Ground💩 👉It's been another full week and she's doing great , very nice Growth, considering shes been up against the wind and rain 👈 No problems 😊 so far so good 👍 I GOT MULTIPLE DIARIES ON THE GO 😱 please check them out 😎 👉THANKS FOR TAKING THE TIME TO GO OVER MY DIARIES 👈 👉NutriNPK NUTRIENTS USED FOR FEEDING 👈rain water to be used entire growth👈 👉www.nutrinpk.com right now get 10% off using SPRING2022 as the coupon code👈

Gracias al equipo de AnesiaSeeds, Marshydro, XpertNutrients y Trolmaster sin ellos esto no sería posible. 💐🍁 Sticky Boof: Prepárate para dejarte llevar por Sticky Boof, nuestra última obra maestra que está poniendo el listón muy alto para los amantes de las índicas. Nacida del legendario cruce de Super Boof y Cadillac Rainbow, Sticky Boof es una potente planta con un asombroso 80% de dominancia Indica que promete una relajación sin igual. Prepárate para un viaje épico con el asombroso 37,5% de THC de Sticky Boof. Sumérgete en una cosecha abundante con Sticky Boof, que produce hasta la friolera de 500 g/m² en interior y 800 - 900 g por planta en exterior. Esta variedad es generosa y está lista para llenar tu alijo de cogollos de la mejor calidad. Sticky Boof es todo rapidez y eficacia, acelerando el tiempo de floración en sólo 7 u 8 semanas. 💡TS-3000 + TS-1000: se usaran dos de las lámparas de la serie TS de Marshydro, para cubrir todas las necesidades de las plantas durante el ciclo de cultivo, uso las dos lámparas en floracion para llegar a toda la carpa de 1.50 x 1.50 x 1.80. https://marshydro.eu/products/mars-hydro-ts-3000-led-grow-light/ 🏠 : Marshydro 1.50 x 1.50 x 1.80, carpa 100% estanca con ventanas laterales para llegar a todos los lugares durante el grow https://marshydro.eu/products/diy-150x150x200cm-grow-tent-kit 🌬️💨 Marshydro 6inch + filtro carbon para evitar olores indeseables. https://marshydro.eu/products/ifresh-smart-6inch-filter-kits/ 🍣🍦🌴 Xpert Nutrients es una empresa especializada en la producción y comercialización de fertilizantes líquidos y tierras, que garantizan excelentes cosechas y un crecimiento activo para sus plantas durante todas las fases de cultivo. Consigue aqui tus Nutrientes: https://xpertnutrients.com/es/shop/ 💻 Trolmaster Tent-X TCS-1 como controlador de luz, optimiza tu cultivo con la última tecnología del mercado, desde donde puedes controlar todos los parametros. https://www.trolmaster.com/Products/Details/TCS-1 📆 Semana 4: Continuamos la etapa de vegetación, ella se desarrolla muy bien 😎, comienza el buen tiempo, temperaturas agradables para todos. Esta semana se aplica una solución de trichodermas para una mejor adaptación aunque realmente va genial. Se mantiene 1/3 de nutrientes Master Root y Master Grow

Following The Grow Boss tips on YouTube "...yield is based on light, quality is based on growers talent" "...number one problem is, too much light, too much water, too many nutrients" Nutrients : (after having issues with nut burns, I decided to use Grow Boss's perfect ppm calculator) Invasion T (Glomus intraradices BEG72 and TRICHODERMA atrovide MUCL45632) 1g / plant Monster X mycorhizes (500 000 propaguls / Kg , made in vitro) 2g / 20cl then complete to make 1l Humic Fulvic Booster (humic and fulvic acids) 1ml / 1l Cannazym 2.5ml / 1l Rhizoponics 0.4ml/1l Lights: 2 x Adjust-A-Wings Avenger 600w HPS Lumatek 90000 Lumens 1000PAR 600w HPS Philips Son-t Green Power 95000 Lumens Soil:Platinium Royal Mix premium quality What is vapor pressure deficit? Often, marijuana growers who have their plants in indoor grow tents or rooms with artificial lighting, take into account parameters such as temperature and relative humidity to maximize plants growth and bloom, thus obtaining abundant harvest with top quality flowers. As we will see later, these factors affect different processes of the plant, such as transpiration or nutrient uptake. However, we usually forget about another important factor that is related to the aforementioned ones: vapor pressure deficit or VPD. Broadly speaking, VPD is the difference between the amount of water vapor that the atmosphere is able to retain (which depends on temperature) and the amount of water vapor contained in it (relative humidity). It is usually measured in kilopascals (kPa). Providing our plants with a correct relationship between temperature and relative moisture will keep us on the right VPD parameters, increasing the plant’s activity and thus improving its growth and showing its full potential during the flowering phase. The ideal would be to adjust both parameters (temperature and humidity) to get the best possible VPD value, so that the development of plants will be amazing.In the chart above you can see the right temperature and moisture values to maximize the development of cannabis plants. The green zone shows you optimal values of VPD, in which it would be ideal to maintain the environment. The orange zone shows correct values, in which plants should not have problems to develop normally. However, red areas show values in which your plants will be very far from hit their full potential, since the relation between temperature and moisture is not optimal. With relatively high values of VPD (between 5 and 12) plants tend to open their stomata and release a considerable amount of water vapor into the environment (increasing their transpiration). This increase in transpiration results in an increase in the plant’s photosynthetic activity, which will need more nutrients and will improve its overall growth, both during growth and bloom. The best range is between 7.5 and 10.5, which we have marked in green. However, we must be careful that VPD is not too high (dark red zone) since the plant would close its stomata to avoid releasing too much water vapor to the environment, which would result in fast dehydration due to excessive transpiration. On the other hand, if VPD is too low (light red zone), the plant will also close its stomata for not releasing more water into the atmosphere, which in this case would be already saturated (it would have reached the maximum water retention capacity in a specific temperature). In this way, reducing transpiration will also reduce photosynthesis, which has a direct impact on the plant’s development and yield. That way, VPD is essential when it comes to offer the best conditions for the development of plants, also to understand its water requirements according to the nutrients used and thus adjust them correctly to meet the grower’s expectations. N/B: SAY NO TO DRUGS -[Day 90] The plants are getting massive, not a lot of space left in the room, each pictures are token back against the wall or on top of a chair. The Super Skunk shall be ready first , the trichomes are visible without using a microscope, the scent is like an amazing candy floss coated with Skunk pee 😅Boerejongens quality @Home 😊 -[Day 93] Switching Buld Lumatek 90000 Lumens 1000PAR to SuperPlant Super Red 85000 Lumens 2000K 1498nm Lightening under the 1500nm wavelength (2000K) just between the NIR and the Microwave length, can't stand in the room too long without getting tears and shining eyes. Buds shall start to blowup like pineapples, increasing yield. -[Day 98] Everything is getting frosty. Starting to decrease RH . -[Day 103] Today the Y Griega started to push on her terpenes, believe it or not that plant smell stronger than the 6 giants Skunks (the Skunk strain is already a very strong smelling plant), she smell like a coffeeshop front door, the fragrance is absolutely amazing and fantastic, I will definitely grow a full crop of that strain ! -[Day 105] 42 days of Blooming folks ! It's getting serious now 😄 If it can helps you to realize, each plants gots 4 side and a middle, each sides gots 4-6 buds and there's 5-6 buds in the middle, there's 11 plants of 1,60m/5.25ft, how many buds does it makes ?? The correct answer will win 1 like 😅😂😅😂 -[Day 106] WEEK 7 of flowering, the end is close my friends, I'm trying to give you the best shots as possible, I wish I'd could share a good smoke from this crop with you guys ....😉

Training still going well. Top is pretty even with some slower lower branches I may remove. Have a mite problem so I introduced 5 ladybugs that immediately went to work on the soil and leaves. Watering when dry but may end up transplanting into new soil if the bugs keep on bugging. Continued training a bit and decided to defoliate and take off some of the lower branches lacking growth. Continuing to water when dry while preparing to add more nutrients for flower production. Hoping she takes it well!