Flowers are developing nicely but slowly. Very few feeder leaves are turning yellow yet. I saw some webs between one of her branches and Fractal, so I sprayed them with alcohol and burned some leaves. She and Fractal have the same dense bushy structure. The buds are tight to the stems which traps humidity and moisture inviting pests and fungus. After post, I had to chop one main cola due to rot. Pics above.

Esta semana la dejamos más tranquila a la Jack solo le hicimos un trasplante a 5 litros quedo bien , la dejamos recuperar unos días y después le hacemos las últimas podas y ya va a estar lista para florecer

Denn Ladys geht es bis jetzt hervorragend. Die Buds werden jetzt so langsam dicker 🎊✌️

Howdy, So this last week has been about learning, quickly. Plant 2 has been suffering from yellowing, I noticed that at first it was a darker green than plant 1 - (first signs of Mg deficiency I have since learned). As plant 1 was doing so well until a few days ago, I originally assumed that plant 2 was just a bit of a slacker. I think basically it is more susceptible to PH differences than plant 1. First mistake was not knowing about the benefits of PH range... What I did not know earlier in the week is that Mg and Ca are only absorbed efficiently at 6.0 and above, my OCD kicked in and I refused to let the PH wander above 5.7; as from what I have read in forums, 5.7 is the sweet spot. Main lesson from last week is that I'm not going to be so anal about PH levels, I will let the PH rise to 6.3 before I drop it back down to 5.7, this will give the plants and window of time to grab hold of some well deserved CalMag before I drop it back down so it can retrieve some Mn and P if it needs any. My plants told me they were in need of Calcium over a week ago, but I naively thought that maybe I spilled a droplet of water on one of the leaves, and that caused it to burn. As I was adding CalMag+ to the solution when I replenished the reservoir. My second mistake was panicking... After realising above, I bombed the nutrient solution with 35ml of Cal Mag, bringing up the PPMS to 460, this subsequently gave the strongest plant nutrient burn. On top of this, I gave both plants a foliage spray during lights out with some diluted CalMag as well. So anyway, the main thing I have learnt is when the plants are ill, its probably best to take it easy, do a res swap at the very worst and concentrate on my PH levels first before throwing more variables into the fray. Positive notes: Plants 1 & 2 is now working on their 5th node, I know I am technically allowed to top at this point, but I am going to wait until they are working on their 7th before doing anything, this way I will be able to tell if the new growth is looking healthy, and my investigations are correct. I have now installed a Hailea 150a, with a submersible pump, this is now keeping the reservoir at 20ºc and its keeping the nutrients well mixed, I'll post a video later this week showing the set up. The roots at the top look a little dark, but I have done a sniff test and they don't smell at all, I think it is just where some of the tea has built up where the bubbles meet the air. Roots do seem rather large, maybe they have stretched so far looking for Mg and Ca :P Decided against increasing PPMS, going to do another week, so 5 weeks veg, gives the ladies some time to recover. Trimmed the burns off of leaves mainly so I can keep a track to see if damage is continuing. Anyways, I hope the above makes sense and draws other newbies attention towards PH ranging for hydro; I have posted a pic which shows the PH range for each important element. Thanks! 😊

Hey Cannafam, Well weve reached the end for this gorgeous gal, i did want to leave her another week but ive been informed that my landlord wants to inspect the property in 2 weeks, so shes come down and needs to be dried jarred and the tent put away! In the final week i managed to flush her and the light was dailed down to 56%(61 watts). Again humidity was high at 70% with 23c temp, VPD of 0.84 and DLI at 35. Although i was not able to control the environment completley in her final weeks, this gal has performed like a champ, she has built solidly throughout with a maximum of 80 watts from my little rig so a really energy efficient grow 😊 Trimming was very difficult, as she was so low down ive wet trimmed in the pot some and then had to dig to cut her main stem. She was just one massive brick of bud when i took her down 😁 and i must say i definitely fell in love with this chunky woman. Further trimming will be done when shes dried out more and il update with the final dry weight and smoke report later. I hope you've enjoyed this diary, stay safe and remember the Sun always shines in Space 😊✌️💚💚💚

Altra settimana volata via per la BISCOTTI🍪 by ZAMNESIA con PLAGRON nutrient 🍽️ad alimentare le ragazze che stanno bene le cime stanno ingrassando 💣sempre di più e il gelo ❄️è ormai esteso ... il profumo dei fiori ⚘️🌻è molto intenso.....dolce... sembra delizioso❤️

Plant keep growing great. As you can see at the leaves there are some of the tips of the leaves with bad color, thats because teh EC reached up to 1,8 so I added ph leveled plain water with 0,4 ec to lower the ec to 1,5 and the plant is responding really well, growing faster and with a healthy root system. The temperature was high also (near 30 degrees celsius) so i moved the lamp upper and i will setup an 100mm fan for extraction. The led panel is really really hot

Meine Pflanze wachsen nun seit 2 Wochen nicht mehr. Bleiben bei 77 cm stehen. Die Buds werden kompakter und der Geruch wird intensiver. Die Parameter im Zelt sind gut und stabil. Eine Pflanze bekommt gelbliche Blätter. Es ist Sweet Candy. Alle anderen sind noch schön grün. Leider durch das Licht der NDL nicht so gut zu sehen. Habe mit einem Mikroskop versucht den Reifegrad der Blüten zu sehen aber es wackelt alles und ich kann kaum was erkennen. Es ist ein LED Taschenmikroskop. Bekomme eher einen Knick in der Pupille. Hat jemand einen Tip oder Empfehlung für einen besseren Weg die Trichome zu begutachten. Je näher die Ernte ansteht desto ungeduldiger werde ich. Gestartet bin ich am 19.11.23. Es sind nun 18 Wochen um und ich bin zufrieden. Werde euch weiter auf dem laufenden halten und freue mich natürlich auch mal über einen Like oder Kommentar oder Tip über den Erntezeitpunkt. Bis dahin wünsche ich allen Growern eine gute Zeit.

The plant has entered an active flowering phase, has undergone defoliation, feels good

Booming if i do say so myself :) scrpg installed on the set up which is a 120x60x150

Ya la quiero cortar, me dicen que tengo que esperar mas tiempo , por los pistilos que sean marrones, que falta madurar!

❄️👋❄️ Depuis quelques temps je ne vois pas beaucoup ma culture car j'ai déménagé et qu'elle ne se trouve plus chez moi. Je passe la voir uniquement pour l'arroser, environ une fois par semaine. J'ajoute du Bioenhancer une fois sur 2. Malgré mon absence les plantes m'ont l'air d'être en bonne forme. Pourvu que ça dure ! ❤️️🤞 Intensité de la FC3000: 90% Ventilation : Extracteur mars hydro 6 pouces avec filtre à charbon puissance : 4/10 (24h/24h) + 3 ventilateurs à l'intérieur ( ON 8/24h). ils s'activent à un horaire différent. 🌟Venez me voir sur Instagram 🌠 https://www.instagram.com/hou_stone420/ 👨‍🚀❄️❄️❄️👋❄️❄️❄️☄️❄️

Esa familia, finalizamos la 3 semana de floración la verdad que poco cambios en la flor, en verdad odio la autoflorecientes en indoor, me parece que son mejor opción os un Exterior o un balcón pero, ante todo os tengo que mostrar la experiencia con autos también y que mejor genética que la misty gorilla autofloreciente de Zambezaseeds. Y es que entre la variedad y la alimentación que estamos aportando, gracias a AgroBeta están respondiendo bastante bien, en las próximas semanas imagino que empezaré a notar diferencias ya. Ph regulado en 6.2 temperatura entorno a los 26.5 grados y la humedad está en 50%. Sufro de una pequeña placa de mosca del sustrato, a estas alturas poco afectará pero vaya, que sepan que con el calor del verano pues también sufrí algún problema respecto a esto anterior. Me despido entre buenos humos, hasta la próxima semana.

Ha avuto dei problemi appena nata. Già alla terza settimana e altra 5 cm era già in fioritura purtroppo si è presa troppa acqua per via della pioggia. Ma si è ripresa subito e mi ha fatto un raccolto piccolo ma buonissimo

Inizio nuovo ciclo Giovedì 26 settembre 2024 Aggiungo 75 lt acqua osmosi inversa ec 146 ph 9 Aggiungo tutti I nutrienti ottenendo ec 908 ph 6.5

Hello everyone 😎 Week 2 of flower for the Gorilla Cookies auto from Fast Buds 💥 She grew fast with a beautiful green color,for the nutrient 4ml/L terra bloom & 1ml/L power buds from Plagron Spider Farmer SE-7000 60% Have a nice day 😋

1/20/2023- So much to do pre grow and over the next 16 days, absolute first order of business is that I have to take down my current Grow---TIMBER-- Then I have a list of things I have to get done in order to be ready to start this grow 1 Feb. With that said T - 2 days until start 48 hour Flush T - 2 days until Start 48 hours of Light T - 4 days until TIMBER!!! Items that need to be done before 1 Feb 2023 1. I need to clean the tent out 2. I need to clean the equipment- Proper Sanitization between grows in Hydro is a must!!! 3. I need to get the hole in the ceiling above my tent repaired- For my last grow I had a deep sink installed in my grow room, to make Hydroponics a little bit easier and have a water source in the same room. The seals on the pipes they were installing broke and leaked through the ceiling causing some damage all the way across my grow room, I was already weeks into my grow and couldn't risk them working above my tent and it would have been very awkward positon for them to be working in as well, so have to get this done quickly between chop and germination. 4. I have to install my new light- I was using a Vivosun 4000 and for this grow I am switching up to a Spider-farmer SF 7000. 1/20/23- For this upcoming grow I am working with M/F photo seeds so I ordered 4 Sex determination kits. I recieved my my 4 Sex determination testing kits from Rimrock Analytics today. I will be using these to test my plants at week 2 of Veg so that when/if I take clones I know I am taking them off females. As well as I don't want to accidently pollinate my tent during this grow I am looking for big beautiful buds not seeded buds. :-) 1/24/2023- Harvest of current grow- Started at 2:00pm and finshed wet trim and firt batch into the freeze dryer. 1/25/2023- Next batch into the freeze dryer and cleaning all my equipment for this Grow. T-1 Day until the workers are supposed to be here to fix the hole in the Grow Room. T-3 days until I instll my new Gorilla Grow Tent and my New Light Spider Farmer SE-7000 for this grow. T-7 Days until Start of Germination 1/26/2023- Harvest is done ran through the Freeze dryer and dry tim completed. 1/27/2023- Grow Room repairs completed. Hole is gone Letting the paint dry before I install the new tent. T-2 days until Install the New Gorilla Grow tent and the new Light T-3 days until I put the hydro equipment in the new tent T-5 days until Germination 1/29/2023- Day 0- Final Pre Germination activities Germination Start T-3 days The paint on the ceiling was dry and it was time to finish prepping for Germination. I got the following items knocked off my list. New 4X4 Gorilla Grow Tent is up and ready New Spider Farmer SE-7000 Light is installed- Thanks Moony Grows for the suggestion and for the Code that got me some money off and free shipping (Moonygrows)!! I turned the lights all the way up to max and set the timer to 18/6 0600-0000. I will keep an eye on the temperature and humidity without my plants and see how hot it gets with the new light. I put my Hydro system back together and put in 40 gallons of water into it, time to monitor for leaks the next few days. I Setup my cloning machine for Germination Days 3-11 1/30/2023 let me break down the situation, ROOM in the TENT.. Enough said.. No really I tried putting my exhaust system up in the new tent with my new light, The light is so big corner to corner that it really didn't give me enough room for the lights be be raised, with the exahust hanging the buckets my plants are Starting in are 2 and 1/2 feet off the ground, great for plenty of room for roots but not so great for upwards space for the plant to grow. In a 6' 11 tent with the exauhst in side and hanging that only gave me a little over 4 feet of grow room to play with. My last grow if you saw my diary, anyone could tell I was struggling to keep the buds off the lights. No good, Since space was such an issue I was running my carbon filter inside on the ground but It really needed to be up sucking the heat out not shooting the cool out. With that setup I was sucking air through the filter and pushing it out the tent at a bottom exhaust hole cold out. Wasn't doing me any good for my heat. I was hitting temps of up to 85 degrees. I bought a portable AC unit and have been running it in the grow room to try and keep temps below 85 and I have had to lower the power on my lights during grow also not ideal.. With that said a friend of mine MoonyGrows (Check out his diary) took the time to look at my issue send me a picture of my grow tent setup with detailed instructions on how to suck the air out from the top but putting my filter and fan on top of my tent so no room issue and I am sucking the air out from the top where the heat is instead of pushing the air out from the bottom where the cool is... THANK YOU MoonyGrows For taking the time to help me get this straightened out.. Now I have room and I have the exhausts working right and now my temps with everything at 100% are topping out at 80 this dropped the temp by 5 + degrees at 100% max. T-2 days until Start of Germination Prepped my seed tray with humidity dome Prepped my Rapid Rooter plugs. I Used RO water, and I added a few drops of Hydrogen peroxide to Oxygenate the water. I then PH balanced between 5.7-6.0 the same that they will be getting in the Cloning Machine and when they get to thier final grow pod. I perfere the 5.8x range and I hit 5.84 for these rapid rooters. If you want to see a complete video on the process HowWeedGrow has an amzing video that shows step by step how to do it and explains it better than I ever could including how to plant the seeds. Which I will cover when I get to that step on Wed. https://www.howweedgrow.com/how-germinate-weed-seeds-cannabis-rapid-rooters/ 1/31/2023 T-1 day until Germination Start All set and ready have my Rapid Rooter plugs ready to go have my seeds out.. Have my seed tray warming up tonight. Tomorrow morning right into the Rapid Rooter then strait into the tray. I will spray the dome to start the humidity in there. 2/1/2023 Germination Day!! Let the games begin! 0600am Put the seeds into the Root Riots. And then put the seeded Root Riots into their first home the Seed tray. I have them under the light 24/7. Sprayed the dome 7:30pm Sprayed the Dome to keep humidity going on the dome. 2/2/2023 Day 1 of Germination Sprayed the Dome in the morning Sprayed the Dome in the evening 2/3/2023 Day 2 of Germination Roots are starting to come out the bottom of the root riot plugs and the heads are slowly popping out of Number 4 just below the surface. Afternoon- Number 4 has popped up Evening- Number 3 has popped up as well. Happy Dance!! 2/4/2023 Day 3 - Germination Surprise Surprise Surprise- all 4 have now poked their heads up.. Happy day!! 100% Germination succeeded. Now major milestone to track is how many are female and how many are male. I will take look at the roots this afternoon/evening and see if they have enough root to go into the cloning machine for the next 7 days before they go into their Hydro Pods. Day 3 - Germination - Evening.. Roots looked good and they were tall enough to make it into the cloning machine. Now that they are all in the cloning machine I have switched the lighting to veg state 18 on 6 off. 2/5/2023 Day 4 - Germination - Morning All the Ladies (fingers crossed) looking great stretching nicely and look nice and green, Photo synthesis underway.... UPDATE!! After a very interesting POD cast on FSTS by Dr. Bruce Bugsbee from Utah University, I have shifted my lighting to 24 hours on through seedling and then I am going to shift to 20 hours on the rest of Veg. 2/6/2023 Day 5 - Germination While Checking on my conditions inside the new tent last night, I found that the Humidity was down to 39 Percent. I added an AquaOasis Cool Mist Humidifier, the reason I selected this humidifier is that I needed one that could be turned on and off utilizing my Inkbird Humidity Controller IHC200 that I have my Pro Breeze Dehumidifier currently running with. Root structures are starting to get there about 1/4 of an inch. 2/7/2023 Day 6 - Germination Everything seems on track more roots poking out of each today. They are each getting a little taller as well. Checked in the evening and number 3 was drooping the Root riot plug on the bottome was dry and the roots were not in the water yet. I raised the water just enough that the longest root that was sticking out is now hitting the water. 2/8/2023 Day 7 - Germination Everything looked good while checking in on them this morning number 3 is now full up and no droop again. 2/9/2023 Day 8 - Germination T-2 days until Plant into Forever Pods and we start week 1 of Veg .. :-) Surprising thing to me is that number 1 and 2 were later in popping then 3 and 4 but the roots are growing longer in 1 and 2. 2/10/2023 Day 9 - Germination Number 1 and Number 2 are definitely ready for transplant today.. Based on how they were yesterday and where they are today I am hoping by tomorrow 3 and 4 are ready. Today they look to me where 1 and 2 did yesterday.. I really hope 3 and 4 catch up by tomorrow since.. T-1 day until transplant to new/ final home for grow. Need the roots long enough to have some clay down in the basket to keep the root riot out of the water and only roots in the water.. 2/11/2023 Day 10 - Germination Today they got placed in thier forever Home, 7 days from Sprout and 7 days until Week 1 Start. PPM- 180 this is water out of the Tap Temp Water: 70.7 Temp Tent: 77 Humidity: 40% I have a humidifier going 24/7 to try and bring this up.. I also have Humidity Domes on each plant. 2/12/2023 Day 11 - Germination Sprayed the domes, all are looking good.. Nothing much to do at this phase but Keep monitoring the PH level in the system and making sure they have a comfortable home. T-6 days until Week 1 start 2/13/2023 Day 12 - Germination Sprayed the domes, They were looking a little yellow today so I moved the light down to assist. Nothing much to do at this phase but Keep monitoring the PH level in the system and making sure they have a comfortable home. T-5 days until Week 1 start 2/14/2023 Day 13 - Germination Sprayed the domes, They were looking a little Florissant yellow today, with what looks like slight burn on the tips, I talked with a fellow grower and we agreed that It was probably that I was drowning them, Yes you can drown you plants even in Hydro, but only early on.. :-) It usually happens with the water being too high, which soaks not only the roots but the medium (root Riot plug in this case). I lowered the water from touching the bottom of the pot to about 1" away. This will probably take 3-4 days to resolve. I will continue my daily monitoring. T-4 days until Week 1 start 2/15/2023 Day 14 - Germination Sprayed the domes, continue my daily monitoring they look a little darker green instead of lime green now that I lowered the water levels in the system, so I think that I might have resolved the issue but it will take a few days for recovery to happen. T-3 days until Week 1 start 2/16/2023 Day 15 - Germination I looked in on them this morning, 3 and 4 look like they are doing well and recovering nicely. Number 1 not so much it has brown spots on the leaves, this very well can still be a side effect of the overwatering but I decide to go ahead and add Nutes earlier than I was planning just incase. I was going to wait until Saturday but I think intervention is necessary now especially after drowning them early on. I added 1/2 what I am planning on adding for week 1 start. I also think I am going to adjust my chart to add 1/2 2 days after plant from now on. I don't think it would hurt it to have some Nutes to pull from. .25ml/Gal Calmag = 12.5ml 1ml/gal GH FloraMicro= 50ml 1ml/gal GH FloraGro = 50ml 1ml/gal GH FloraBloom = 50ml T-2 days until Week 1 start = I will drain the system and start it over on Saturday with Week 1 Nutes. 2/17/2023 Day 16- Germination I didn't even want to post today after looking in on them this morning, 3 of the 4 are now showing signs of dronwing.. Brown spots on the leaves, the water levels were still too high.. I drained about another inch out of the tanks.. Will see how quick they recover.. I start week 1 tomorrow and will have to ensure my water levels are at least 1" away from the basket on this round.

Last week only lots of tap water for my Mexican Ladies. Her leaves got a bit yellow but that was expected and planned. Today was the day to thank them for their service and I cut them both down to drie, with all leaves included except for the fan leaves. Can't wait to see and test the results! She is not a heavy packer, in weight it won't be a lot but I am aiming for Quality > Quantity 😏

Petit problème sur un de mes plant je pense à un blocage nutritif Je vais donc leur donner 5l à chacune histoire de leur faire un runoff et enlever les sdk minéraux accumulé dans le Substrat A part sa le strech commence et la bonne odeur se fait sentir 👃