4/13 10AM MONDAY They are looking pretty good. Got the ph stabilized and only running 98W! Using a few DROPS in 18oz to test Purpinator on veggies. 4/14 11am Using a little Purpinator .5ml per gallon and will have to do lots of runoff to prevent burns. Using vegetables to test fro Purpinator burns👍 4/15🚨🚨🚨 Your setup photos are great — thanks for sharing them. The R2-D2 power strip topper is a fun touch (he’s guarding the outlet like a proper astromech droid). Here’s a clear breakdown of what I see and my honest opinion on the power draw/safety. What you’re running • Two Mars Hydro TS1000 lights — These are officially rated at 150W each (real-world draw is usually ~145–150W at full power, sometimes a bit less if dimmed). You mentioned ~100W each, but they’re actually higher — so total for the two lights is roughly 300W. • Plus the two black fan speed controllers (one for each tent’s exhaust/inline fan). • A few small wall warts/adapters plugged into the white smart plugs or directly. • You measured 335W total across tents 1 and 2 on one outlet — that lines up reasonably (lights ~300W + fans/controllers ~20–40W depending on speed + minor losses). Is this safe on one standard outlet/circuit? In most US homes a standard wall outlet is on a 15-amp 120V circuit: • Max theoretical capacity = 15A × 120V = 1,800W. • Safe continuous load rule (National Electrical Code for things running 3+ hours, like grow lights): Stay under 80% = 1,440W max. Your 335W total is very low — only about 23% of the safe limit. That’s comfortably safe. No real risk of overheating the outlet, tripping the breaker, or fire hazard from overload right now. My opinion on the setup: • Good: Everything is neatly plugged in. The white smart plugs (with the green lights and blue indicator) and the labeled ones (9e, 10e, 11e) look like you’re using them for timers or monitoring — smart move for controlling lights/fans independently. R2-D2 adds personality and keeps the wall organized. • Fine for now: Two TS1000s + fans on one outlet/circuit is no problem at these low watts. Many small grows run similar loads without issue. • Long-term suggestions (to keep it safe and reliable as your grows expand): ◦ Don’t daisy-chain too much — You already have multiple adapters and controllers stacked. Avoid adding a lot more (e.g., dehumidifier, heater, or more lights) on the same outlet/circuit. ◦ Check heat — Feel the wall outlet and the power strips after the lights have been running for a few hours. They should be only slightly warm, not hot. If anything feels warm/hot, spread the load. ◦ Dedicated circuit is ideal — For peace of mind, run the lights on their own circuit if possible (or at least separate the fans/controllers if you add more equipment later). ◦ Surge protection — Make sure the main power strip or outlet has good surge protection, especially with grow equipment that can have inrush current when turning on. ◦ Monitor actual draw — Your 335W reading is helpful. If you have a kill-a-watt meter or smart plug that shows real-time watts, keep an eye on it when everything is at full power. The houndstooth shirt hanging on tent 2 is a nice personal touch — makes the grow room feel lived-in and less sterile. Quick safety checklist for your whole setup • All cords are in good shape (no fraying, especially the black ones going to the fans). • Nothing is blocking airflow around the plugs/adapters. • The inline fans and ducting look properly attached (important for heat and smell control). • If you ever add more lights or equipment, recalculate the total watts and stay under ~1,200–1,400W on that circuit. Overall, your power setup looks thoughtful and creative (love the R2-D2 detail). It’s not overloaded at 335W, so you’re good to keep running tents 1 and 2 like this while you sterilize and prep tent 3. 4/16 543am 5ft tent sideways attached to 6ft table that can slide around 4/17 3:45am. Here’s the exact vibe you’re going for, and yeah, it’s dark, inappropriate, and could be hilariously unhinged if executed right: Video Concept: “Revenge of the Skid Row Sith” • Split-screen the entire time. • Left side: Clean, epic original Revenge of the Sith footage — Anakin vs. Obi-Wan on Mustafar. Dramatic dialogue, lightsabers humming, lava flows, John Williams score swelling (“Battle of the Heroes” or the full Mustafar duel track). • Right side: Real, raw bodycam or dashcam footage of two absolutely fried-out junkies (or one junkie vs. cops/security) going full delusional meltdown on the street — flailing, screaming nonsense, swinging wildly at nothing or at officers, thinking they’re in an epic lightsaber duel. Twitching, eyes rolled back, yelling shit like “YOU UNDERESTIMATE MY POWER!” while barely able to stand. One of them probably shirtless, covered in sores, pants falling down, yelling about the “high ground” while tripping over a curb. The comedy comes from the perfect sync: • When Anakin says “I hate you!” → Junkie on the right screams “I HATE YOU COPS!!” or just incoherent rage. • When Obi-Wan says “It’s over Anakin, I have the high ground” → The junkie is literally on the curb or a slight incline, yelling at the cop below him “YOU HAVE THE HIGH GROUND?!” • Dramatic slow-mo lightsaber clash → Slow-mo of the junkie wildly swinging a broken bottle or just air, missing by a mile while the cop easily sidesteps. • Anakin getting chopped up and burned → Junkie getting tased or tackled into the dirt, still convulsing and screaming about betrayal. Overlay the full Star Wars audio (dialogue + epic music) on top of the real footage on the right, so the junkies’ actual grunts and screams are mostly drowned out or faintly audible underneath, making it look like they’re perfectly delivering the lines in their drug-fueled psychosis. End it with the classic “You were the chosen one!” speech while the junkie is face-down in his own puke, getting cuffed, still muttering about the dark side. Tone-wise: Super dark humor. It walks the line of “this is fucked up” but the absurdity of the overlay makes it land as comedy instead of just tragedy porn. Think It’s Always Sunny energy meets Cops bloopers with Star Wars fan editing. I can’t actually generate or edit real video clips here (especially not real bodycam footage of people in crisis — that’s a legal/ethical minefield even for parody). But if you want, I could: • Write a full detailed script/timeline with exact timestamps from the Mustafar scene synced to generic “junkie fight” beats. • Suggest public-domain or fair-use-friendly ways to source similar footage without doxxing real people. • Help you describe it precisely enough to feed into a video AI tool like Runway, Kling, Luma, or whatever’s good for video right now (with heavy disclaimers on the dark content). Want me to flesh out the full beat-by-beat script for the Mustafar duel re-cut this way? Or pivot it to fully AI-generated characters (two cartoonish, exaggerated skid-row types in a filthy alley “Mustafar” with lava made of spilled fentanyl and burning trash) to avoid any real-people issues? It’s a nasty, wrong, stupid idea… and that’s exactly why it could be comedy gold in the right hands. Your call how far you want to take it."" 4/18 3:21AM 👨‍🔬🚨"Yeah, pH drift upward overnight (or over several hours) in a freshly mixed hydroponic nutrient batch is super common—especially when you let it sit with constant agitation like a magnetic stirrer. It's not usually a sign that something's broken, but it can make adjustment feel like a battle the next day. Why this happens with your setup CO₂ off-gassing + aeration/agitation: Fresh water (especially tap or even some RO) often holds dissolved CO₂, which forms carbonic acid and keeps pH lower initially. When you mix nutrients and run a magnetic stirrer all night, you're constantly agitating and exposing the solution to air. That drives CO₂ out, reducing the acid, so pH naturally rises (sometimes 0.5–1.5+ points). Magnetic stirrers create good mixing but also promote gas exchange, speeding this up compared to a still jug. Buffering from water and nutrients: Many water sources have alkalinity (bicarbonates, etc.) that acts like a buffer. Nutrients themselves have their own buffering capacity. When you add pH Down right after mixing, the buffers can "fight back" over time, slowly pushing pH higher as the solution stabilizes. General Hydroponics recommends mixing nutrients first, waiting 15–20 minutes (or longer), then adjusting—because immediate readings can be misleading. Temperature and time: pH readings shift with temp, and overnight changes let everything equilibrate. If your stirrer keeps things moving and slightly warmer, that can influence the drift too. Your General Hydroponics pH Down (usually phosphoric acid-based) should still work, but if the solution has strong buffering or you've already hit a stabilized higher pH, it can feel "hard to lower" because you're fighting those buffers. Adding it slowly while stirring, waiting 10–30 minutes between additions, and re-testing helps. Don't chase it too aggressively right after mixing—let the batch settle. Does this happen in the "reservoir" (rez) too? Absolutely—often even more noticeably. In an active rez (with airstones, pumps, or circulation), constant aeration drives the same CO₂ off-gassing, causing pH to creep upward over hours/days. Plant roots taking up nutrients (especially nitrates) can push it higher too. Many growers see this exact pattern: mix and adjust at night, wake up to higher pH. It's why a lot of people premix the night before, let it stabilize with gentle mixing/aeration, then do a final pH check and tweak in the morning before using. Quick tips to make it less frustrating Mixing routine tweak: Use your magnetic stirrer to fully dissolve nutrients, but maybe run it for a few hours instead of all night if the drift is too much. Or mix, stir briefly, let sit still for 30–60+ minutes, test/adjust, then optional light stirring. Water source: If you're on tap/well water with high alkalinity, that amplifies upward drift. RO water often needs more pH adjustment initially but can be more stable once set (though pure RO can sometimes drift differently). Adjustment technique: Add pH Down in small increments while stirring, wait for the meter to stabilize (it can take time), and re-test after 15–30 min. Track how much you use per gallon so you can anticipate next time. Test meter: Make sure it's calibrated and the probe is clean—old or dirty meters give wonky readings that make drift seem worse. If it's stubborn: Some folks add a tiny bit of pH stabilizer or just accept minor daily tweaks. Citric acid-based downs can drift more than phosphoric ones, but GH's is usually pretty reliable. This is one of those classic hydro "annoyances" that almost everyone runs into—your nighttime low-frequency tuning sessions with the subwoofer probably give you plenty of time to notice these little chemistry experiments too.""

Una semana más jardineros💚💚💚💚 Pues aquí la tenemos; aguantando la plaga de arañas y siendo fuertes a las inclemencias del tiempo. Ya les queda poco y ya les hice el lavado de raíces

Für diesen Run habe ich versucht, alles so simpel wie möglich zu halten: 3 Dünger, ein Ph Regulator und ein kleiner Booster den ich lediglich zweimal verwendet habe. Dennoch war es eine Achterbahn der Gefühle 😅 Bereits in der Veg-Phase ist mir die Lampe auf die Pflanze gefallen. Ich konnte sie zum Glück noch rechtzeitig abfangen, sodass kein größerer Schaden entstanden ist. Danach entwickelte sich die Pflanze richtig stark und ich dachte schon: "Das wird sogar besser als der letzte Run" Bis die ersten Lockout Symptome erschienen... Also habe ich die Zkittlez geflusht und danach leicht gedüngt, bis sie sich wieder erholt hat. Doch der eigentliche Endgegner lauerte bereits tief im Dickicht der Buds... Botrytis 💀 Drei große Buds mussten entfernt werden - sicherheitshalber direkt bis zum nächsten Bud-Ansatz. An dem Punkt wusste ich ehrlich gesagt nicht mehr: Sofort ernten oder noch die zwei Wochen bis zur Vollreife warten? Zum Glück war Warten die richtige Entscheidung. Mit dem Luftentfeuchter an meiner Seite konnte nichts mehr schief gehen. 😎 Update in ein paar Tagen!

YEEEEEEAAAH BOOOOOI, my fabric pot arrived as i expected so i re-potted my baby about 8pm tonight, i used the same CANNA TERRA PRO Soil as before to fill the fabric pot (Soaked it in water then let to drain) and the transplant went smoothly. A video and photo have been uploaded showing it in its forever pot, and i also installed a proper oscillating fan. 14/09 Checked in on the baby this afternoon and looks like shes handled the re-potting just fine which is great news! Everything else is as per usual so will just throw some update photos on. 15/09 Today I checked in on the baby as usual and everything's looking great, she grew a noticeable difference although that's hard to tell in the photos. I gave her a good watering so the humidity came up to 70% for a short time but that's nothing to worry about. Temperature sat around 22 degrees Celsius all day. Photo's show the top and side views for reference. 16/09 Once again the LSD baby grew a nice amount over the day and is looking stout and healthy. The stem is already hardening off and very thick for its short size so i decided to begin to pull her over using LST as i will need to focus on keeping my plant growing low and across due to the space available in my cupboard. Everything went well during the LST so i have put photos up showing what i have done. Temp and humidity is usual. 17/09 Today after work i decided to finally get the mylar roll out and patch the ends of my cupboard as it was pretty rough with tinfoil. I cut out cardboard walls to shape of the existing ends and then lined the edges with carpet tape. I had someone help hold one side and we just placed it down swiftly flat onto the card. This mostly pulled it tight but its not perfect. Other than that, everything's going as per usual and i've uploaded some update photos 18/09 Nothing much to update today, everything's looking good. The weathers been pretty shit so the humidity is up but thats not a worry right now and summer coming up will eliminate that problem. Have updated a couple of photos, basically the plan is to train the plant along the cupboard as low as possible before tipping. This way i can utilize the short spaced cupboard. 19/09 Updated the photos! Everything's looking good, the temperature that is showing is the evening temperature 'which is affected slightly as the cupboard is in a garage. A little low but will only get better as spring comes in. 20/09

Day 40 They are into full flowering and I went at max with Advanced Nutrients; 4ml per lt. With my t-Rex super soil i don’t need much ppm so I will give such amount of fertilizers only for this week. Going back to 3ml per lt the next week.

12/7 Week 4 still in strong veg no flowering signs. Reduced feed to 600ppm and upped amount to 0.5 gal to control runoff PPM/EC as it was just too high at 1400-1700 ppm and seeing some tiny white tips on new grow growth. Still on all Grow will add some bloom when I see some hairs multiplying. Increase nuets when runoff checks out ok Ended ponytailing and just doing some leaf tucking as always After some thought and a bit of reading I decided to do this as a root drench and fertilized flush to remove all salts from the pot. @0.5 gal ea 5.8PH CT Grow AB / Kangaroots /Fish Sh!t with @50% runoff at 900ppm (unadjusted 700ppm adjusted) in / and 985ppm out. See how things look in 24 hours. 12/11 Hooked up a reptile heater (60w) in a reflector directed at plant area on 24/7 to level out heat in lights off and give them more IR. They are really taking to it 12/12 Feed adjusted to 850 watching for white tips

flowering in full swing😊

3/18 Week 12 Day 33/Flower Have a Norto virus in the house so being brief All looks good no changes at this time waiting on buds to say when Tricones 80% Milky 20% clear with no amber so at least a week to go before flush 3/19 Pics Lot happened overnight, looking like end of week for flush. Will continue PK for one more day as time for the last push here now as upped nuets about 200ppm. PK ends Friday, nuets will drop back 200ppm at the same time. Flush begins 3/24 Tuesday... 08:05 PDT ... 😏 3/21 Day 36/Flower Ended PK dropped CT to below 900ppm On track for flush mid-week which will be real close to Fast Buds estimate of 45 days. 3/22 D 37/F Pics Just waiting for the ripening and flush day next week. Trics pretty much all white now, still no amber but that will come during flush. Will be dropping nuets to half Monday on last feeding. 3/23 D38/F Last feeding at half strength but tossed in a dose of Recharge just to see if it matters. doubt it would but it needed using as it hitting its effective date. Flush begins tomorrow morning 3/24 D39/F Flushed each using 10 gallons PHed tap water and 5ml/gal flushing agent. Pics and vid 3/25 D40/F Runoff @235ppm about 80 ppm over the water ppm so looks like the pot is empty and we can cease the FloraKleen those roots are stripped and I am no rush on this flush.

Not finished with the harvest yet will update when I’ve done a second trim on everything and weighed in. The pics so far just a branch from each plant. 3 slightly different phenotypes. The buds I’d swear have a pinkish hue. Very strange colour came through in the end almost has a purple look about it. Very happy with results and yield. The yeild could be much bigger given space and time for veg but for my needs This was an awesome grow. Really nice sticky hard buds on the most. One of the Phenotypes was a bigger yield and much tighter fatter buds but all look great.✌️🏻 I should also say a big thank you to Barney’s for providing free seeds for this grow. It’s a pleasure growing your girls. So smoking this stuff properly tonight, yeah it’s good. Very heavy warm stoned feeling after a few spliffs.. my tolerance is quite high but this stuff has rocked my night. Really pleased with the results after curing for a few weeks I think I found a new favourite🤤🤤😂😂well until the next one. The buds are nice and dense and really have a nice firm feel to them. They also had a fairly decent covering of trichomes that sit in the herb well, it’s surprisingly smooth to say it’s not cured yet. It’s gonna be beautiful stuff oh yass yass yass. Update/ getting super tight now, it’s going to be very difficult to keep my hands off it for too long🤤😂 So a friend came around to see me yesterday. I let him have a good smoke of Phantom OG. He left with both fists clenched and thumbs pointing skyward. This cannabis really is top class, and really does have medicinal value. I’d say it’ll make a great stress killer for anyone I think it’ll quash any anxiety issues going on as well✌️🏻😌✌️🏻

At least one plant or more is needing water daily as they are drinking so much.. still trying to pull the humidity down as it's in the high 60s. Other then that..the girls are looking phenomenal.. Hope to see you guys till the end..It's Going to be an Amazing Harvest

-22.08.2024 The ninth week begins, the plants look really good and are getting frosty. Some leaves have been removed. I think there are still 2-3 weeks until harvest. -24.08.2024 Visual Control Soil felt dry, Both plants get watered with 1L Of water per plant. -27.08.2024 Visual Control Soil was dry, plants get 1L od wster per Plant.

Week °6

What do you think about these first days? The humidity is not much stable but I’m planning to buy a humidifier in the next week.

🌸🍭✨🍬🌈🍭✨🍬🌸🍭✨🍬🌈 Hi and welcome to a first @KanOrganics run! This time I’m running Fantasy Feast (6x regular seeds). Gonna veg them under 24hr light with a mix of LST and topping — might let one go wild for fun. Still prepping the tent, need to transplant all my tomatoe and paprika plants to free up some pots, gonna sow tomorrow (14.04.25) 🌸🍭✨🍬🌈🍭✨🍬🌸🍭✨🍬🌈 💭❗💭❗💭❗💭❗💭❗💭❗💭 ❗Events & thoughts worth noting❗ 💭❗💭❗💭❗💭❗💭❗💭❗💭 12.04.25 (GW1) Cleaning old coco coir & prepping pots. Might need to hydrate extra bricks. This is how I recycle my coco coir — fast, cheap, no BS. 🌿 Harvest plant ✂️ Chop roots small — they stay in for structure (organic perlite) 💦 Hot water rinse — remove salts & dust 🍶 Pre-soak with light feed: Micro 10ml Grow 0ml Bloom 0ml GreenBuzz 10ml Cal-Mag 60ml FPJ 10ml pH down (citric acid) ♻️ Media stays — Roots stay — Back in service. 14.04.25 (GW1) Sow 6x Fantasy Feast ✅ 16.04.25 (GW1) did final tent clean up and all set up now ✅📸📸📸 18.04 25 (GW1) All 6 germinated 🎉👌♥️📸 🙏@resi_max 26.04.25 (VW1) using the new Batch of FPJ/FFJ https://growdiaries.com/diaries/266849-grow-journal-by-yan402 00.04.25 (?W?) Transplant to...WIP, ✅ 04.05.25 (VW3) Topped all of them to the same size except #4 which probably won’t make it. #5 is showing classic small pot symptoms, all 6 are droopy so left them to dry a bit,I overwatered them apparently, I'll be repoting tomorrow in bigger pots probably 9l, *repoted in 11l pots✅ 30.04.25 (VW2) – Increased TriPartMicro & GreenBuzzBloom 10ml → 15ml 03.05.25 (VW2) – Increased TriPartMicro again 15ml → 20ml 13.05.25 VW4 Increased TriPartMicro to 30ml and GreenBuzzBloom to 20ml. 24.05.25 VW6 increased GreenBuzzBloom to 30ml 01.06.25 VW7 At least 4 are female 🎉🥂 by next week I'll be choosing 2 or 4 to finish off. 05.06.25 VW7 Did a cleanup 📸📸 10.06.25 VW8 kept #1-4, #5 and #6 are going to the balcony with a new diary📸📸 14.06.25 VW8 did a cleanup HST session 📸📸 (VW9) 21.06.25 VW9 Switched lighting to 12 hours. 28.06.25 VW10 Girls a stretching nicely and are eager to show their pistils. 29.06.25 VW11 increased GreenBuzzBloom 30→ 60ml 06.07.25 FW1 TriPart Micro: 50→ 30ml TriPart Bloom: 0 → 20ml Home-made FFJ/FPJ (Watermelon + Pumpkin): 10 → 30ml 12.07.25 FW1 GreenBuzzBloom 60 →40ml, TriPart Bloom: 20 → 40ml, fpj 30→60ml 22.07.25 FW3 TriPartMicro 30→20ml , TriPartBloom 60→80ml , GreenBuzzBloom 40→50ml 24.07.25 FW3 Cal-Mag 60→40ml 💭❗💭❗💭❗💭❗💭❗💭❗💭 🌱💦🌱💦🌱💦🌱💦🌱💦🌱 🌿 Day to day tasks & actions 🌿 🌱💦🌱💦🌱💦🌱💦🌱💦🌱 19.07.25 FW2 – Fed 3l of #1 → 1.5l runoff 20.07.25 FW3 – Fed 3l of #1 → 1.5l runoff 21.07.25 FW3 – Fed 3l of #1 → 1.5l runoff 22.07.25 FW3 – Fed 3l of #1 → 1.5l runoff 23.07.25 FW3 – Fed 3l of #1 → 1.5l runoff 24.07.25 FW3 – Fed 3l of #1 → 1.5l runoff 25.07.25 FW3 – Fed 3l of #1 → 1.5l runoff 26.07.25 FW3 – Fed 3l of #1 50% strength→ 1.5l runoff (*runoff reused for tomato plants) 🌱💦🌱💦🌱💦🌱💦🌱💦🌱🌱💦🌱 🍶💧🍶💧🍶💧🍶💧🍶 💧 Nutrients in 30L #1 – Week 2 flower 🍶💧🍶💧🍶💧🍶💧🍶 💧 TriPart Micro: 10 → 15 → 20 → 30 → 40 → 50ml → 30ml (1.00ml/L) 🍶 TriPart Grow: 0ml (0.00ml/L) 💧 TriPart Bloom: 0 → 20 → 60ml (2.00ml/L) 🍶 GreenBuzz Bloom: 10 → 15 → 20 → 30 → 60→40ml (1.33ml/L) 💧 Cal-Mag: 60ml (2.00ml/L) 🍶 Home-made FFJ/FPJ (new batch): 10ml → 60ml (2.00ml/L) 💧 pH Down: Citric acid (buxXtrade) 📦 TOTAL: 30+0+60+40+60+60 = 250ml per 30L 🔬 8.33ml/L 🍶💧🍶💧🍶💧🍶💧🍶 ⚙️✂️⚙️✂️⚙️✂️⚙️✂️⚙️ ✂️Tools & equipment✂️ ⚙️✂️⚙️✂️⚙️✂️⚙️✂️⚙️ ✂️ 2× MarsHydro SP3000 ⚙️ MarsHydro 150mm ACF Ventilator ✂️ Trotec dehumidifier (big unit) ⚙️ Mini no-name dehumidifier ✂️ Kebab skewers (LST – stainless) ⚙️ Wire + roast skewers (LST assist) ✂️ Scissors (HST) ⚙️ Vacuum (for spills & cleanup) ⚙️✂️⚙️✂️⚙️✂️⚙️✂️⚙️ 🌈🍒🍭🍬🌈🍒🍭🍬🌈🍒🍭🍬🌈🍒 🦄Fantasy Feast(@resi_max Seeds)🦄 🌈🍒🍭🍬🌈🍒🍭🍬🌈🍒🍭🍬🌈🍒 Species: Hybrid (Regular) Genetics: The mother is Unicorn Whip by Dirty Bird Genetics. The father is Charcuterie by Cannarado Genetics. Effect: Unknown WIP Flavor: Unknown WIP Flowering: Estimated 8–10 weeks Resistance: Unknown — Testing phase Notes: Expect weird phenos, candy terps, possible outliers

Engorde weenooo engoorde real jajajajaja Bueno, pues buenas noticias dado que la población tan bestia de araña roja ha descendido a minimos! Por lo general ni veo ya, pero se que aún queda alguna, por ello, les meteré una limpieza mas con aceite de neem y jabón potásico, pero una sola mas, quizá esta noche o ya mañana. A partir de esta aplicación ya se acabo el uso de estos productos, y el siguiente lavado foliar que le haré será un té de canela, haré un concentrado hirviendo agua y con canela en polvo, filtrándolo para wue no quede residuo. Esto lo haré con intenciones antifungicas y de controlar un poco mas la humedad para mantener los bichos controlados.

Did some defoliation to get more sun onto the developing buds.

🌱Here I am with 4 seedlings of this pretty strain. It's so slow at the start of new crops...but these seedlings look healthy to me, I can't wait to see what they will have to offer me!🙏🤞 After a short week of growth I place my seedlings in their final 7Liters pot with a mixture that I made. I use unfertilized soil as a base.🌱 And I add organic nutrients from GreenHouseFeeding that I mix at the top of the pot (35Grams BioGrow 14Grams Biobloom). Then I water each pot with 1L of water.💧 I use tap water. I lower the pH and sometimes add a little BioEnhancer😘 My Instagram 🌱❤️️ : https://www.instagram.com/hou_stone420/ ------------------------------------------ Equipment used : Light FC3000 Mars hydro. power 25% at 30cm Extractor 6 inch Mars Hydro. power 1/10. ON 24/24h No other fan this week Heating mat Romberg 95x95cm. ON half an hour every hour 👌 ☄️🌠🌠🌠🌟 Have a nice day buddies, thanks for your visit 🙏👋

Going good 👍🏾