23.05. today is the end of the fourth week for the plants, they haven't progressed much since last week, they grew a few cm and gained a little weight, but they are healthy, which is the most important thing... in a few days I will transplant them and top them because some of them have already developed the sixth pair of leaves, so I simply have to top them. turned out... I thought of transplanting them into 10-liter pots and after two to three weeks into 50-liter holes, however, the weather didn't cooperate, and I was already late anyway because of the bad weather, and because of the same, my plants in the fourth week were the same as they should have been in the second, and because of the same, I couldn't even transplant earlier... now that nothing went according to the "plan", of course, I don't know how smart it is to transplant them into 10 L and then into 50 with the fact that it is with me the longest day of the year is June 22, so that actually a week after that it can start flowering (it usually starts at the end of July or at the end of August, but it can be late and start even in September, and it also knows how to plow and start already at the end of June)...now I think that it is better to buy smart pots of 50-60 liters and immediately transplant into them and then just bury them...another problem with that is that the soil that I took for vegetation has food in it for a month days, if I transplant twice, it may happen that it enters flowering, and the food for the vegetation has not yet been used up, and that would be a problem...advices are welcome Stay high!!!

For this grow I've used, For the growth 1 sf1000 2 fan 15w 1 extractor 150mm 350m3/h 1 carbon filter 150mm 1 Hydro Shoot 60x60x140 1 timer 1 thermostat Heating system for the winter month 11l RQS Fabric Pot and 11l plastic pot. 20 Hours On, 4 hours off light For the soil I've used plagron light mix ont the top + batmix in down pot + rqs pellets. For the blooming 1 Mars Hydro TS1000 (150W) 2 fan 15w Extractor + Filter 150mm 1 HS60 box 1 timer Same pots 20/04 Plagron lightmix + batmix + RQS Pellet After harvest, I've put the stuff in a room with 2 fan 15w, weather are really hot and dry, condition are not well, around 25/32*C and 40%HR, hope will be not dry too fastest. Thanks for all my friends! And again thanks to RQS and @James, and Mars Hydro, @Coco_Pan2022 ❤️❤️❤️

12/09/2022 - 36 days since my little girl sprouted from seeds🌱 The first week of flowering my Mandarine XL 🍊🍊🍊 Nutrients: Jungle Indabox - This week I adjust the dose of nutrients to support flowering and added nutrients - flowering stimulators: Jungle Urban A: 0.5 ml Jungle Urban B: 1.5 ml Jungle Urban M: 1 ml Flower stimulators: Jungle Environ X: 1ml Advanced Nutrients - Bud Candy 2 ml Advanced Nutrients - Bud Ignitor 1 ml Advanced Nutrients - Big Bud 2ml Hesi Root Complex - 5ml - last week of adding this nutrient Atami - ATA Calmag - when growing under LED lights it is recommended to use Calmag and Atami is an excellent brand, I give the same as in vegetation: 0.5ml. Lights: I don't change Bloom light, I still use Mars Hydro TS1000 - 150w full spectrum, great light to use both in vegetation and flowering 💡💡 Training: LST: third attachment of all twigs where flowers are formed 🌸🌸 Defoliation: the first big defoliation took place in the middle of the week, I removed the large leaves at the bottom of the plants and those that shaded the flowers 🍃🌞 The little girl has only grown by 5 cm since last week, she is already putting all her strength into flowering. The pistils at the ends of the twigs already form white tufts 😊💓 I can smell a subtle scent of herbs and flowers, but very subtle indeed. I'm already looking forward to the girl smelling the whole room and I can smell all the notes of her aroma🌼 Thanks for the likes and you can follow me on Twitter 🐦: @ Targona666 See you soon 😍

Hi, we’re back for week 3 of the vegetative stage. It’s not great… I decided to repot my plant into a larger container with a new nutrient-free substrate. I went for a coco-perlite mix and placed it in an 8.5-liter pot. The plant hasn’t really grown since last week, so I put it under an Autopot dome to maintain better humidity. As you can see when I zoom in, it’s struggling to get going, with very little visible growth. I kept the COB lighting to maximize vegetative growth while avoiding too much heat. Conditions are stable: around 25°C and 50% humidity in the grow tent. That’s not very high, so I added a small water tray to try to boost humidity a bit. For the parameters, pH stays around 6. I slightly increased EC to 1.2 and switched my base nutrients to the Athena line: Grow A, Grow B, and CalMag. Let’s see if these changes pay off next week. See you then, bye!

Im quite sad about the end result of the Exodus Cheese. I expected something different. Anyway sometimes you find something great and sometimes you dont. Thats just part of the game. Im not complaining about greenhouse seeds tho, i have found quite some bangers out of their seed packs in the past. Looking forward to new grows. Peace out growmies.

~ AirCube Active Oxygen Ebb/Flow System sponsored by GrowAce, featuring Tropicana Cookies by FastBuds ~ Well guy's and gal's here we go again on another exciting Autoflower run together! This time will be different as I will be doing a 'Hydroponic' run utilizing the AirCube Active Oxygen Ebb/Flow System by GrowAce, who were kind enough to sponsor me for this run, so it should be interesting to see what results I get and have some fun along the way! •Let me first tell you about this 6 Pot Ebb/Flow system from GrowAce: "The AirCube system is the one and only Ebb & Flow grow system on the market that combines the benefits of air pruning with a fully automated Ebb+Flow system! With the AirCube's proprietary fabric pot in bucket design, this system is guaranteed to outgrow any other Ebb + Flow system on the market. The results speak for themselves- grow MASSIVE roots that result in MASSIVE fruits! Air Pruning- Air Pruning only happens with fabric pots. As the roots reach the fabric walls of the pot, they penetrate and grow into the breathable fabric. Once penetrated, the roots are exposed to air, which causes the tips of the root to dehydrate and naturally prune themselves. This natural pruning process forces the roots to grow tons of lateral fibrous feeder roots. This results in a plant that utilizes the entire root zone and fills the entire pot with tons of roots. These fibrous feeder roots are incredibly effective in uptaking water and nutrients, resulting in a plant that grows healthier and more vigorously! Oxygen Benefits- Without oxygen, nutrient absorption cannot occur. On a molecular level, oxygen is needed to transmit nutrients across the cell walls and into the roots of a plant. With the AirCube's proprietary bottom lifted draining design, the system actively draws all of the water out of the bucket pulls vital oxygen into the root zone. Maximum Versatility with Any Grow Medium: The AirCube System is the only system on the market that allows you to use any growing medium you like. Use coco coir, soil, peat moss, perlite, vermiculite, hydroton, rockwool or any other medium you wish! This system is the most versatile Ebb and Flow bucket system in today's hydroponics industry. Temperature Control- with the fabric pots constructed with highly porous polypropylene fabric, heat dissipates easily and effectively. Unlike standard plastic pots, heat isn't trapped in the root zone. Heat in standard plastic containers can reach temperatures of up to 125 degrees. When this type of heat is trapped and unable to escape, it can damage your plant's health and limit the potential of your harvest. Growing in the AirCube System, plant roots grow cooler, healthier, and more vigorous. Largest Pots in its Class- this system features 5 Gallon grow buckets, the largest pot size of any other ebb and flow hydroponic system in the market. Modular and Expandable- start with 6 grow buckets and expand up to 36 grow buckets with the optional 105 gallons PopTank reservoir!" For my medium and nutrients I decided to also switch things up from my regular Organic runs, going with Plagron Nutrients and Root Royale 70/30 Coco/Perlite. When filling the fabric pots with medium, I first added just under a gallon of horticulture perlite from Nor-Cal as a base layer to ensure good drainage and then filled the remainder with the Root Royale. •Now for the outstanding, award winning strain from my friends at FastBuds... Tropicana Cookies Auto: I'll be running Tropicana Cookies Autoflower which is a 60/40 Indica/Sativa Hybrid. "Tropicana Cookies Auto is the perfect variety for growers of all levels, especially beginners as this strain performs very well outdoors and indoors, and can produce up to 500 gr/m2 in 56-63 days without needing extra maintenance. Reaching up to 110 cm, this strain grows fairly tall with medium-sized branching, showing its mixed heritage. Definitely the right choice for those with a high tolerance looking to get their hands on the strongest autoflowers out there. You can expect an extremely powerful and long-lasting high that’ll boost your mood and give you that extra push you need to start your days on the right foot. This variety offers the whole range of citrus and woody flavors with a strong candy-sweet background that will keep you coming back for more and more."* *References: GrowAce.com, 2fast4buds.com ______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ The Setup: • AC Infinity 4x4 tent •AC Infinity Cloudline T6 Exhaust Fan w/ Controller 67 •HLG 650R w/UVA Bar *** For some reason GD does NOT have a listing for the USA version of the 650R so I selected the closest match to it. •AirCube Active Oxygen Ebb/Flow 6 pot System •DL Wholesale Root Royale Coco Lite 70/30 coco/perlite •TrolMaster Hydro-X Controller for light •AutoPilot APC8200 co2 controller fed by a 50# tank •16" Hurricane oscillating fan and 8" floor fan •Tent cooling via filtered outside air delivered by AC Infinity Cloudline T6 fan •BlueLab instruments: PH Pen and Truncheon Nutrient Meter ______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ Weekly Updates: 11/5- Well here we go into the second week of flower for the FastBuds Tropicana Cookies! All three plants are now in flower, with the #2 & #3 ahead by about a week. I have done LST on all three, tying down branches with horticulture wire. I've also done some defoliation on each plant as they got extremely bushy and were getting zero light down into the lower sections of them. All have responded extremely well to the training and are looking great! Tomorrow I will empty and clean the reservoir along with the 'brain bucket' as the water has really gotten funky and has an odor that I don't like. Going forward, I'm going to be doing weekly changes on the reservoir where I'll empty/clean/refill and add fresh nutrients. In between changes I'll just be topping off the reservoir with straight water and only checking the PH. 11/7- Yesterday I emptied, cleaned/disinfected and refilled the reservoir and 'brain bucket' with well water. After filling, I added Plagron's Cocos 'A' and 'B' in equal portions, Green Sensation, Royal Rush and Power Roots. I also added a dose of silica to this batch @ 1.2ml/g. The plants are all doing alright, the #3 does have some spotting beginning on her leaves in in margins, and has never had the darker green of the other two pheno's. 11/9- I'm continuing to adjust the LST wires on all three plants to try and keep as much light penetration down into the centers of the plants which has been working well. I have also removed a shade leaf here and there when necessary. The plants are really doing well in this AirCube system and I'm slowly getting a better handle on its 'in's & out's'. I did also check the ppm's of the return solution to see if there was a wide variance from what was going in, and all was good with only a 50-100ppm difference. 11/11- The spotting on the #3 pheno has cleared up nicely, and she's the tallest of the three plants @ 24". The #1 and #3 plants, although not as tall, have flowers that are getting a beautiful dark purple coloration in them, while the #2 pheno's flowers are pure white, with only a slight hint of purple coloration showing. Tomorrow I will be doing a drain/clean/refill on the AirCube system, along with fresh nutrients, which the girls should really enjoy! There's two weeks of flower behind these girls, with another six to eight to go which will be getting more exciting as the weeks progress... I can't wait!😎 💚 Thank you for checking out my passion in life! Please visit as often as you wish and I hope you enjoy this journey as much as I know I will! Grow what you love, Love what you grow!💚

One of them is showing calcium deficiency but I will add some calmag from Biobizz and hope it will solve the problem. I live in a very humid area and its raining all the time so it's very hard to maintain a low humidity level. I follow a VPD table (vapor pressure deficit) and with the 25º C and 55% RH its a good indicator for flower. Feel free to ask anything! :D

Happy with my plants 😊🙏

Week 8 Looking absolutely huge😂 They’re so tall and wide . Lots of healthy green leaves and strong roots. I was worrying a lot about sex issues as when I did my research I found out they’re quite common to hermaphrodite. Was really worrying but all calyx’s have female signs (so far🙏🏻) so pray for me brothers&sisters.

Note : + jegliches Zubehör wird in der GermniationsWoche aufgelistet . Zeitraffer Videos folgen immer nachträglich. + videos werden so geschnitten das nur ein geschlossenes Zelt erscheint , ergo Fehlen paar reale Minuten (ca 1 Std) . Sanlight Tageslichtzyklus in Lebenswoche 6 : + 200PPFD - 1h - 750PPFD - 16h - 750PPFD - 1h - 200PPFD = DLI 46.60 + + Formel : DLI = PPFD * h * 0.0036 + + in LebensWoche 6 ist der Max-DLI ohne CO² : 45.0 Dazu kann man sich gerne die Zeitraffer angucken . Die Pflänzchen brauchen schon Ihre Zeit auf touren zu kommen . Ergo ist Sonnenaufgang und Untergang reines Stromsparen . Day 36: + 2Liter Flaschenwasser + + Dünger für Büte + + + Canna Terrar Flores (Achtung wirkt wie PH-) + + + Canna Boost + + + Cannazym + + + Canna Rhizotonic + Final : PH 6.2 Nach dem die Mangelerscheinungen wie gewünscht aufgetreten sind, gehts jetzt mit Blütedünger weiter . Sie hat sich prächtig in die neue Umgebung eingelebt. Wetter werte sind hier Super , also ist auch im Zelt super Stimmung :)) Videos folgen in den Tagen . Day 37: Sie wächst gerade noch paar Zentimeter :)) Blühten werden mehr . Day 38 : Und wieder das Licht etwas höher händen , den Sie wächst noch immer !!! Day 39 : + 2Liter Flaschenwasser + + Dünger für Blühte + + + Canna Terrar Flores (Achtung wirkt wie PH-) + + + Canna Boost + + + Cannazym + + + Canna Rhizotonic + + + Greenhouse Feeding BioEnhancer als PH+ + Final : PH 5.5 (das Urgesteinsmehl zieht das sowieso auf mindestens PH 6.5) + etwas Entlaubung der defiziet Blätter. Day 40: Day 41: + 2Liter Flaschenwasser + + Dünger für Blühte + + + Canna Terrar Flores (Achtung wirkt wie PH-) + + + Canna Boost + + + Cannazym + + + Canna Rhizotonic + + + Greenhouse Feeding BioEnhancer als PH+ + Final : PH 5.5 (das Urgesteinsmehl zieht das sowieso auf mindestens PH 6.5) Day 42: + 2Liter Flaschenwasser + + Dünger für Blühte + + + Canna Terrar Flores (Achtung wirkt wie PH-) + + + Canna Boost + + + Cannazym + + + Canna Rhizotonic + + + Greenhouse Feeding BioEnhancer als PH+ + Final : PH 5.6 , Drain PH 6.89

This Wedding Cheesecake is growing very strong! She has a few double stems! This makes it look like she's topped herself on a couple of her branches. She's getting watered with about 1/2 of a gallon of de-chlorinated tap water.

3/11 🍓🍑 They were a little dry this morning, so I gave them a gallon of water split between the four of them using the light schedule feed🎄 3/12 Z🍓🍓🦍 strawberry and strawberry gorilla are starting to get very tall. They’re becoming huge. I’m gonna keep them at 91 W maximum that might even be a little high. It’s nice to know. They don’t take as much light as I thought along time ago. They really look good. this is the first time I’ve used 2 gallon pots so I have to remember to water more often and spray the bag with neem oil. I can’t tell if it’s runoff salts or if it is some sort of white fungus that’s not good on the outside of the bag, either way, if I spray everything with neem oil before I water including the soil, NO the plants just the soil and the bag makes a huge difference.🎄👍 3/13🍓🦍🍑💦 💦plus silica after about 12 hours, they are looking really good. They’re actually dry again. I’m gonna do watering tomorrow. The CBD plant is going completely different than any other one. It’s really exciting. It looks great but very different from any of the other ones probably because I dropped it when I did the transplant either way luckily she’s doing great.👍 3/14 🍓🍑👍 3/15 🍑🍓🦍💦💦💦 I ended up doing two full gallons of water. I was surprised how much I had to water them with today did full nutrients and supplements.💧💧💧 3/16🍓🦍🍑 strawberry gorilla and the strawberries are growing exactly like they said they were on their website. They’re looking just great apricot and the CBD are also doing great. I’m not gonna do too much training. I feel better if I leave them alone.👍🍓🦍🍑 3/17 Z🍓 🍓🦍🍑💦💦 1 gallon with 1 mL silica 1 mL Cal mag💦💦

Super excited for this run. I'm always on the search for new quality genetics and fruity terps. This time I chose Elev8. I watched an interview with them and decided to try. They start all their genetics with high quality clone cuts. Pretty interesting and if you ask me that's how I'd do it if I was gonna to something like that. Water for 36 hours then in the solo cup. 80% filled with my mix and the top 20% is just coco/perlite. 5/6 popped up. We begin!

Overall very pleased. All the leaves are dark green and the plants are looking very happy. I’m giving them a couple more days before they are flipping into flower. All of them handle defoliation really well but Somango is a little to bushy to really do any organized Lst. I will try after Defoliation next week and give her a bit more surface area.

Bending, tucking, wireing. Jackie seems to love it all, my fastest plant so far from seed. She is enjoying sun and few hours a day of CFL-s. Light nutes dosages seem to suit her needs, bacillus and myco doing their job very well, more than happy I am what can i say :) __________________ Update 13.10. I Decided i want to try supercropping on an auto strain, my jack is groeing ultra fast on a daily and i blv today is kinda good day considering the growth of an auto and her life cycle.. you can see the training i am doing as well, every 2 days i must move green wires and gently stick them to soil not to hurt roots, and spread them side branches that have 2 pair of nodes already. Lets see how will she respond in the next days :)

Tomorrow I get a aircon to reach 60/16