We harvested one little bud this week. Now we have realised that it was probably premature, but the pistils were orange so we just decided to. We are drying it outdoors in a plastic box with a fan attached to a little solar panel. We will harvest more next week, but right now it is not looking good in terms of the harvest.

Week 5 day 35 today I turned the plants 180° and defoliated not too sure if I absolutely butchered them but its done now time will tell....they've been watered straight after also I've noticed no yellow tips or deficiency on leafs all through pur which is shocking...this strain is the best one I have grown soo far I've done about 5 so far over 10 years with big gaps so learning again for sure slowly 👍 would like to grow this again soon but properly next time... temps are around 26-27 still using the cfls to keep temps up and is going well so far. Im looking for seeds for next time I want to grow but can't seem to find this strain anywhere 😕

The buds are still bulking a little more as of day 64. The trichomes are pretty milky/frosty so the harvest is getting close, but I am not going to rush it if the plant is healthy and the buds are not suffering. My best estimate right now would be between day 68 and 78 for harvest. Day 67: areas of amber colored trichomes are appearing on the calyxes, under 10 percent of total. this is what I have been watching for to indicate harvest time so I will be giving water from here out and begin cutting down the plant in a few days. Thanks for reading!

Drying and curing process as the rest plants in the tent.

Method 🎚️ Medium: 🥥🥥🥥🥥🥥 1 volume emoji because there really was no method to this grow. Plant seed, let grow, cut down, enjoy regularly😉. Any time you have the luxury of rooting this plant in the earth (where it belongs) is a huge bonus. She didn’t need much of anything and took all she required (for the most part anyway) from the garden👍. OG’s in the emerald triangle pride themselves on the makeup of their soil and the quality of the plants they grow. I like to think that while this girl didn’t have that benefit - she got as close as she could to it here in the north. She was struggling heavy at the start when she was indoors. It must’ve been my error some how but she hated the coco medium, hated the nutes and hated the grow light. As soon as she was moved outside, she was a completely different plant - like she had been begging for the sun the whole time. 5/5 coconuts because you simply can’t beat growing in the ground as the cannabis gods intended😎. Yield🌴🌴🌴 Ahhh the great equalizer of grower egos. Let’s put all of the above in perspective; this girl ended up where she was out of necessity. She was exposed to the elements and potential rippers and named “the decoy” because her express purpose was to draw attention away from the other 2 plants that we didn’t want anyone messing with. Thankfully, no one with a thought to theft ever really noticed her and it wasn’t until late flower that she demonstrated herself to be an award winning plant👍🤘👍. Woulda thought she’d yielded more with how thin her side branches were in comparison to the buds. They were massive and she was ready to fall over by the time the chop window opened. But the buds were also somewhat less dense which made their final sizes a little deceiving. Another limiting factor was that some of her branches were pollinated - probably from a randy bumblebee that had gotten into it somewhere else. Like the other 2 outdoors this year, we pulled 6 or 7 seeds off this girl that may eventually get used in future grows. I’m certainly not opposed to the occasional seed as long as she’s not a full-on hermie that can’t be used. Who knows, maybe a breeding project Is in the cards next year🤔. End of the day, results were about as expected given her conditions and growing environment - 6.51oz of sun grown, sativa goodness👌. 3/5 palm trees for this - without some training and a more accommodating environment - we definitely left some of her potential on the table here. There’s still more than enough to go around though😉. Props Again, a shout out thank you to GD for the platform. Big thank you to HSO for breeding some wicked, awesome beans. And another shout out to good karma for seeing us through this one. Of course some special mention to those who swung in to creep on it these past weeks. Special mention to my buddy @sKitzO for the discussion and sound advice. If anyone’s interested in seeing this plant’s full potential with training and a nute plan then check his dockside, pot-grown 707’s - just gorgeous, abundant, beefcake plants💪. Much appreciated homie👊. From our bong to yours, may the weather be ever in your favour😉😎🤘👍👊.

😍 Ricky G-41

Greetings, fellow growers! Let me share the latest progress of my LSD-25 Auto journey as I navigate through Weeks 9 and 10 of the grow cycle: 🌟 **Vibrant Bud Development**: My LSD-25 Auto plants have entered the final stretch of flowering, with buds reaching their peak size and density. The once-promising flowers have transformed into resin-coated colas, exuding the characteristic psychedelic aroma that hints at their potency. Trichomes are abundant, signaling the optimal cannabinoid profile and a potential journey into euphoric bliss. 📏 **Fine-Tuning Environmental Conditions**: As I approach harvest, my focus remains on fine-tuning environmental parameters such as temperature, humidity, and airflow. By carefully managing these factors, I aim to create the perfect microclimate for my plants to thrive and produce their most potent and flavorful buds. 🍃 **Leaf Senescence and Nutrient Management**: In these late flowering stages, some leaves may naturally begin to senesce as the plant reallocates its resources towards bud production. This process is a natural part of the plant's life cycle and signals that harvest time is drawing near. Meanwhile, my nutrient regimen continues to be meticulously adjusted to ensure the plants receive the essential elements needed for robust flowering and resin production. 🔍 **Trichome Assessment for Harvest Readiness**: With harvest approaching, I'm closely monitoring trichome development to determine the optimal time for harvest. Using magnification tools, I inspect trichomes for signs of maturity, aiming for a mix of cloudy and amber trichomes to achieve the desired balance of cannabinoids and psychoactive effects. 🌞 **Preparation for Harvest**: As I prepare for the culmination of my LSD-25 Auto grow journey, I'm gathering the necessary tools and supplies for harvest day. Trimming shears, drying racks, and storage containers are being readied, while my workspace is meticulously cleaned and sanitized to ensure the preservation of my precious buds' integrity. Proper post-harvest care and curing techniques will be employed to enhance flavor, potency, and overall quality. In summary, Weeks 9 and 10 mark the final stage of my LSD-25 Auto grow adventure, where careful attention to detail and precise cultivation practices pave the way for a bountiful harvest of potent, psychedelic buds. Stay tuned for the next update as I celebrate the culmination of my journey into the realm of LSD-25 Auto. Happy growing! 🌿✨

may 11: start of week 7

Giorno 36 - ho sistemato meglio l’apicale rinforzando con nastro di carta e mettendo il sostegno di gomma sotto. Vedremo nei prossimi giorni come si evolve la situazione. Ho dato 1 lt di acqua a testa in irrigazione Giorno 37 - L’apicale sembra stare decisamente meglio, ogni volta si stacca dal sostegno e cerca di andare verso la luce. Giorno 38 - ho dato 1litro di acqua a testa in irrigazione, domani alzerò i dosaggi di fertilizzanti a 1ml/lt per ognuno Giorno 39 - ho dato 1litro (0,5 l a testa) di fertilizzanti in quantità (1ml/L di bio grow, bio bloom e top max), vediamo come reagiscono le piante Giorno 40 - il terreno é ancora umido, irrigherò domani, sembra abbiano reagito bene alla dose in più di fertilizzanti che ho dato ieri Giorno 41 - ho dato 1litro di acqua a testa perché una delle due aveva le foglie totalmente abbassate, verificherò tra qualche ora se si é ripresa Giorno 42 - stanotte alle 3 le foglie di una erano completamente abbassate di nuovo, il terreno é umido quindi non ho irrigato, credo che annaffierò domani

Dopo aver raccolto la piu piccola che era la più matura ho iniziato il lavaggia di altre 3 mentre a 1 inizierò dalla prossima volta... I fiori più maturi sono bellissimi e il profumo è altrettanto fantastico!!! Le annaffierò altre 3 volte con sola acqua e siamo al traguardo!!!

** COST ** TO RUN - Used previous ⛺️ setup : $0.00 - Monthly electricity : $36.73 <-- other ladies sharing ⛺️ - 1 Gallon Fabric pot : $0.10 - Bonsai wire : Apx. $0.03 - Reused soil from last run : $0.00 FOR NUTRIENTS - Jadam Microbial Solution : $0.00 - Fermented Plant Juice : $0.00 APPLYING - JMS : 30ml / 1 Litter - FPJ : 30ml / 1 litter TOTAL COST : $36.86 Throughout the week, I give JSM, and fermented plant juice once each ^^ Hope you guys have a wonderful day today ^^v *** Please Like, comment & share *** Highly appreciated -----/-----<@

Day 77. Harvest day for that amazing plant. Dry trim chosen. Will update after drying. Thank You Zamnesia for that chance ! Day 86. Girls has started curing process. Happy Growing !!!

Las plantas asimilaron bien el calcio y siguieron adelante, se realizó un trasplante en el día 20, de 300cc a 5lts airpot con solo coco, ahora solo queda esperar a empezar el lst💪💪💪

•••••••••••••••••••••••••• Sept. 26 - Oct. 2 Week 8 of 12/12 •••••••••••••••••••••••••• WEEKLY SUMMARY: •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 🙋‍♀️Fo' Twenny here!🙋‍♀️ We're back with another update on our 🍊🍧ORANGE SHERBERT cultivar bred by BARNEY'S FARM! It's week 8 and all she is looking great as she progresses deeper into senescence! She is really packing on the frost ❄️and her Orange Cream Candy 🍊🍦🍭 fragrance just keeps getting stronger!!! It wont be long before we harvest these beautiful flowers!!! Also, I realized my BlueLab Conductivity Meter has the option to switch to EC. Since EC is the most accurate way to measure the nutrient concentration in a solution, I will now be measuring and reporting EC readings rather than PPM. Any advice, suggestions, or constructive criticisms are always welcome. Now, for the weekly break down! •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• THIS WEEK'S BREAK DOWN •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 9/26 - Day 50 of Bloom °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° 👩‍💻🏼 UPGRADE 👩‍💻 - Upgraded from 8k BTU to 14k BTU portable AC unit! ✂️🍃 PRUNING/TRAINING 🍃✂️ - Selective light defoliation. Removal of dying leaves, leaves blocking other budsites and lower leaves preventing proper air flow. I try to stick to defoliating around 10-15% of foliage at a time and make sure to leave a "crown" 👑 of leaves at the top to absorb photons. If additional defoliation is needed, I will wait at least 3-5 days to avoid stunting growth. 🚿FEED DAY!🚿 - She received approximately 2.5 gallons of nutrient solution. I mixed 8 gallons of solution for all the plants I have in flower. 2.5 gallons of that was then measured and fed to this cultivar. After 10-15 minutes I added additional 12 oz of plain H2O pH to 6.3 👩‍🔬NUTRIENT SOLUTION👩‍🔬 ⬇️Mixing Rundown⬇️ - The solution starts with 12 gal tap H2O through two kdf filters mixed in a 36 gallon reservoir. The solution is applied via wand sprayer powered by a submersible pump attached to a garden hose. Nutrients and additives are added to the reservoir in the order listed below and thoroughly mixed using a plastic stir spoon. The reservoir is oxygenated by four 4 inch air stones. Start pH: 7.9 PPM: 630 1.5 tsp/gal - Fox Farm BIG Bloom 1 tsp/gal - Fox Farm Tiger Bloom 1.5 tsp/gal - Fox Farm BEMBÉ .125 tsp/gal - Fox Farm Cha-Ching I always make sure pH is in the range of 6.0- 6.6 prior to adding any microbial innocclants. pH: 5.8 Add 1 tsp/gal General Hydroponics pH UP pH: 6.2 PPM: 1160 Mammoth P. - 0.6 ML/gal •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 9/30 - Day 54 of BLOOM °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° 📸 PHOTOSHOOT! 📸 🎥 FILMING! 🎥 •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 10/2 - Day 56 of BLOOM °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° 🚿FEED DAY!🚿 - She received approximately 2 gallons of nutrient solution. I mixed 6 gallons of solution for all the plants I have running in this SOG. 2 gallons of that was then measured and fed to this cultivar. This week I used some gallon bottles filled with water and frozen to lower temps in the reservoir. 👩‍🔬NUTRIENT SOLUTION👩‍🔬 ⬇️Mixing Rundown⬇️ - The solution starts with 6 gal tap H2O through two kdf filters mixed in a 36 gallon reservoir. The solution is applied via wand sprayer powered by a submersible pump attached to a garden hose. Nutrients and additives are added to the reservoir in the order listed below and thoroughly mixed using a plastic stir spoon. The reservoir is oxygenated by four 4 inch air stones. Start pH: 7.8 Start EC 1.0 TEMP: 69°F .75 tsp/gal - Fox Farm BIG Bloom .5 Tsp/gal - Fox Farm Tiger Bloom .75 tsp/gal - Fox Farm BEMBÉ .0625 tsp/gal - Fox Farm Cha-Ching Our target pH is in the range of 6.0- 6.6 prior to adding any microbial innocclants. pH already in range, no adjustments needed. pH: 6.5 (No adjustments needed) EC: 1.5 TEMP: 60 °F Mammoth P. .6 ML/gal •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• SUPPLIES & EQUIPMENT CURRENTLY IN USE: •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• • A/C: Whynter ARC-14S 14,000 BTU Dual Hose Portable Air Conditioner • TENT: VIVOSUN 48"x24"x60" Mylar Hydroponic Grow Tent with Observation Window & Floor Tray • POTS: Black 8"tall Active Aqua brand 6" x 6" one gallon square pots/Black 12" tall Active Aqua brand12" x 12" 3.4 gallon square pots • VEG/AUTOFLOWER INTAKE FAN: None (PASSIVE) VEG/AUTOFLOWER EXHAUST FAN : VIVOSUN 6 Inch 390 CFM Inline Duct Fan with Variable Speed Controller • BLOOM INTAKE FAN: VIVOSUN 6 Inch 390 CFM Inline Duct Fan with Variable Speed Controller • VEG/AUTOFLOWER EXHAUST FAN : VIVOSUN 6 Inch 390 CFM Inline Duct Fan with Variable Speed Controller • BLOOM EXHAUST FAN: AC Infinity CLOUDLINE T8, Quiet 8” Inline Duct Fan with Temperature Humidity Controller - Ventilation Exhaust Fan • VEG/AUTOFLOWER AIR MOVEMENT: 6-Inch Lasko FBA 2004W 2-Speed Clip Fan • BLOOM AIR MOVEMENT: One Honeywell TurboForce Air Circulator Fan Black, HT-900 and Three 6-Inch Lasko FBA 2004W 2-Speed Clip Fans • Bluelab PENPH pH Pen Fully Waterproof Pocket Tester • Bluelab PENCON Conductivity Pen Fully Waterproof Pocket Tester • Kolder Multi-Purpose Liquid and Dry Measuring Cup, 16-Ounce • Fox Farm Measuring Spoons • WATER TREATMENT: Tap H2O run through two AQUACREST Garden Hose Water Filters to remove chlorine and chloramine. – COMING SOON: Hydro-Logic 31023 1000-GPD Evolution RO1000 High Flow RO System, White (HL31023). • WATER APPLICATION: I use 2 different watering systems. The pump sprayer is typically used in early veg, between feeds, or for lighter feeds. Most feeds are usually run through the pump and reservoir because it's faster and easier when dealing with larger volume feeds. – 2 GALLON LAWN & GARDEN PUMP PRESURE SPRAYER. * I removed the spray head due to clogs and it's just faster. – Superior Pump 91250 Utility Pump, 1/4 HP in a heavy duty 27 gallon Tote attatched to a 10 foot garden hose to an Orbit Underground 56246 Green Thumb 9-Pattern Telescoping Wand. – Aeration of the reservoir is accomplished using a General Hydroponics HGC728040 Dual Diaphragm Air Pump 320 GPH 4 Outlet attached with standard aquarium air hose to four 4-Inch Air Stone Disc Bubble Diffusers. • VEG/AUTOFLOWER LIGHTING: 320w MosterBoard V4-PLUS powered by a MEANWELL 320H-48AB DRIVER. There are three V4-PLUS boards prewired and mounted on a 935x195x10mm black heatsink. Dimmer, UV Switch, and IR Switch included. Each board contains two hundred fifty two 3000k lm301h diodes + twelve Osram 660nm diodes plus 4 separately switchable LG UV 395nm diodes and 4 separately switchable Osram IR 730nm diodes. • BLOOM LIGHTING: Two custom mounted lighting units: Each mount has one 480w MEANWELL 480H-48B driver and one 240w MEANWELL 240H-48AB powering 6 KingBright Quantum Boards. Each board contains two hundred fifty two 3500k lm301h diodes + twelve CREE XP-E2 660nm diodes plus four separately switchable CREE XP-E2 730nm diodes and four LG UV 395nm diodes. Hanging between the two mounts are two additional quantum boards with two hundred fifty two 3000k lm301h diodes + twelve 660nm diodes plus four constant power 730nm IR diodes and four 395nm UV diodes. That's a total of 1680w of quantum board power in our 96" x 48" bloom tent. ⚠️ ALL DRIVERS MOUNTED REMOTELY IN AN AIR COOLED BOX INSTALLED BETWEEN THE FILTER AND EXHAUST FAN ⚠️ • SLMOTO Universal Oil Drain Pan, 2 Gallon (8 Liter) Capacity ABS Low Profile Oil Drain Pan w/Spout Fit for Motorcycles • Modified Botanicare Low Tide LT Black Tray - 4' x 4' - Modification: Cutaway at corners and used flex-seal tape to create a new edge that will be soft to fit between tent supports. She is supported by 6 Standard Cored Concrete Blocks (Common: 4-in x 8-in x 16-in; Actual: 3.625-in x 7.625-in x 15.625-in). ⚠️THIS TRAY WILL NOT FIT BETWEEN SUPPORTS IN A 48" x 48" or 48" x 96" TENT WITHOUT MAKING MODIFICATIONS TO THE TRAY!⚠️ • Blue Sticky Pads • Yellow Sticky Pads •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• SOIL MIX DETAILS: •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• All components were mixed into a 50 gallon tote that is kept in a warm environment to help innocculate to promote a vast and diverse microbial life in the rhizosphere. Once mixed, add 32-64oz water once every 7-14 days as needed. The goal is to keep the soil moisten without oversaturating. 2 Part - Royal Gold Tupur INGREDIENTS: Coco fiber, aged forest materials, perlite, and basalt 1 Part - Fox Farms Ocean Forest INGREDIENTS: Aged forest products, sphagnum peat moss, earthworm castings, bat guano, fish emulsion, and crab meal. 1 Part - Roots Organics INGREDIENTS: Perlite, Coco Fiber, Peat Moss, Composted Forest Material, Pumice, Worm Castings, Bat Guano, Soybean Meal, Alfalfa Meal, Fishbone Meal, Kelp Meal, and Greensand. Also contains beneficial mycorrhizal fungi: Funneliformis mosseae, Rhizophagus intraradices, Septoglomus desertícola .5 Part - Wiggle Worm Soil Builder Pure Earthworm Castings .5 Part - Ancient Forest Humus .5 Part - Coarse Grade Perlite Inocculated by mixing 1 cup of Extreme Gardening Mycos Watered with pH 6.5 h2O 1 Tsp/gal Real Grower's Recharge 1 tsp/gal Hi-Brix Molasses 2 tsp/gal Fox Farms Kangaroots •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Want to see more cultivars I have growing❓ Please, be sure to check out my other diaries & give me a follow! 👍👍 🙏Thank you for stopping by my garden!🙏 Peace, ☮️✌️ Love, 💚🤟 & Frosty Nugs! ❄️🌲 Happy farmin' my friends! ☺️🌱 - Fo' Twenny 👩‍🌾🏻

Ending of week 3 and beginning of week 4. I started lst a few days ago, now have the top of the plant to the edge of the pot. Just waiting on some of the branches to be able to reach. Plant seems healthy to me but this is my first time.

Papaya cookies are incredible! All the pistils turn purple, incredible beauty of this plant. We are so happy to have caught this extraordinary phenotype and are looking forward to an early harvest in about 2 weeks time.

still no defoliating…

Last week ahead. Next time will cut nitrogen earlier. These ice cream cakes did not like it at this level. Also had a little dripper clog and mokums tulip got a little burnt. At these high ec levels they are super sensitive to drybacks.

This week gorilla cookies finally got the chop! She was a very fun plant to grow and she produced dense,sticky buds that have some very pretty colors to her. If you wanna impress your friends with a plant,she’s one to do it with🔥