I had to cut the girls this week, it's been about 3 days and I think they recovered pretty quickly. Plant 1 drinks 1.7 l, plant 2 - 1.5 l, plant 3 - 0.6 l, plant no. 1 has a mega trunk. I also put them under so that they are the same height.

This plant will be grown again for sure. From start to finish there wasn’t a single issue and she performed well under my Optic LED and LST. Can’t wait to grow this again.

4th week, stop root fertilizers and amino treatment.

Day 85 23/09/24 Monday De-chlorinated tap water pH 6 and calmag today. Day 87 25/09/24 Wednesday Feed today using de-chlorinated tap water pH 6 only. Day 89 27/09/24 Friday De-chlorinated tap water pH 6 with Plagron PK13-14 today. Picture and video update 😎 Day 91 29/09/24 Sunday (End of week) De-chlorinated tap water pH 6 only today. Will start only water next week 👌💚 added pictures 😎 Notes: auto orange bud getting deep purple tips, lovely colour. And deep rich pungent smell. Auto melonade Runtz, absolutely beautiful, pink under leaves, and nice bud structure. Auto overdose, dense compact beautiful structure of a plant 💪💚

you are God

D54 (14/01/2021): First day for week 4 of bloom. I gave them tap water cause last time the PPM run off was a bit high. The PPM run off for Banana Kush today was higher then the run off for Glue Gelato. It's not the first time I see that so I think I can say that Glue Gelato uptake more nutrients compared to Banana Kush. If it become a problem I might consider doing two separate nutrients mix. - temp: 24-27C light ON ; 21-23C light OFF - water: PH6.7, 128 PPM approx. 4L per plant - run off: PH7 and 830PPM for Glue Gelato ; PH6.9 and 1220 PPM for Banana Kush - RH: 55% for light ON and OFF D55 (15/01/2021): I saw some brownish spots on small leaves for Glue Gelato. Last feed, Glue Gelato was the one with the lower PPM run off. I think the brown spots are due to calcium deficiency. Glue Gelato is an heavy feeder, I might give a good dose of nutrients next feed. Glue Gelato PH of the run off was on the high acceptable range. So it might also be a nutrient lock due to inappropriate soil PH. I need to check that closely... - temp: 24-27 C light ON ; 21-23C light OFF - no water - RH: 54% light ON ; 50-52% light OFF D56 (16/01/2021): I fed with 3/4 of the recommended dose for mid late flower. Run off for Banana Kush is still high. I will see how she react but so far she's the one who look the healthier! Maybe she doesn't mind having a ''hot'' soil. It's been 3-4 weeks since I did check the accuracy of my PH meter. I checked yesterday and I was off of PH0.4 (reading higher that it was suppose to be). I have a cheap PH pen so I need to check that often. Maybe the little brownish spot on Glue Gelato is due to incorrect PH in water or soil over the last week. - temp: 24-27C light ON ; 21-22C light OFF - water: PH6.2, 913 PPM less then a gallon per plant - run off: PH6.7 and 1200PPM for Glue Gelato ; PH6.8 and 1700 PPM for Banana Kush - RH: 53% light ON ; 51-52% light OFF D57 (17/01/2021): There's sing of nutrient burn on Banana Kush. It was expected. I consider doing a flush for this gal. - temp: 24-26C light ON ; 21-23C light OFF - no water - RH: 54% light ON ; 57% light OFF D58 (18/01/2021): I mixed 1/2 of the recommended dose of Max Minerals. I flushed the Banana Kush until the run off passed below 1000 PPM. I did not flush the Glue Gelato since there is no sing of nutrient burn. They don't smell that much. When I open the tent, there is a weak smell but when I play with the leaves or shake the stems now I can smell them properly. Glue Gelato have a strong pine-citrus-fruity pungent smell and Banana Kush have a smooth tropical-fruity-candy smell. Both smell soooo good and the buds are starting to look really appealing 😍😋 - temp: 24-26C light ON ; 21-22C light OFF - water: PH6.3, 325 PPM - run off: PH6.9 and 1010PPM for Glue Gelato ; PH6.9 and 920 PPM for Banana Kush - RH: 55% light ON ; 51-52% light OFF D59 (19/01/2021): After 12 days of not removing any leaves today I did removed approx. 20 leaves on each plant. From now on I will continue to remove the leaves that are blocking bud site from having enough light. - temp: 23-25C light ON ; 20-21 light OFF - no water - RH: 53-54% light ON ; 54-55% light OFF D60 (20/01/2021): I gave full recommended dose of Max Minerals, half of the recommended dose of Max Grow and 3/4 of the recommended dose of Max Bud. All base on the recommended dose of nutrients for mid late flower. I was aiming for a lower PPM level then last Banana Kush run off. I dropped de lamp of 1 inch height to be around 13-14 inches from canopy. - temp: 23-25C light ON ; 21-22C light OFF - water: PH6.0 , 775 PPM - run off: PH6.7 and 1200PPM for Glue Gelato ; PH6.6 and 1060 PPM for Banana Kush - RH: 51-52% light ON ; 45-49% light OFF

Nothing to say just i love it 😍 🍒🇺🇲

D1. Three of them make it to 2cm in three days, the fourth one already rooted but taking it easy, I watered them a bit and covered the lazy one to blackout and see if she can do it 💪 Lighting at 8.5 DLI (100 PPFD@24h) with the lamp dimmed at 57cm from the soil. D2. The lazy seed still struggling to sprout but seems she's so close to make it since she's already out the soil. The three strong ones already grew to 4 cm in 24 hours, +2 cm, a growing rate of 0,83mm per hour. Following the seedling schedule lighting now will be at 12 DLI the whole first week. D3. The seedlings are growing strong except the little lazy one, I had to help her sprouting this morning using tweezers since both leaves were trapped inside the seed not being able to open by itself, unlike the other ones that did it by themselves three days ago. Will she gonna make it? Let's give her time 💪 D5. The red worms look very active but the leaf tips are curling up so I moved from 24h lighting to 20h and let em rest a bit keeping 12 DLI and 80% humidity while lowering temp at night from 25°C to 23°C. The lazy seedling still so small and definitely don't match their sisters growth rate, let's see if there is any progress next days. Also I already installed the Blumat, the parcel arrived missing the final drippers and the 3mm tube but they already send it. I adjusted the system following Michael Box top tip on this Growcast podcast, https://youtu.be/g5YFcxW3kXI?si=tkm6F1fF65CaNruq It consist on adjust the holding drip at atmospheric pressure without the ceramic cone/tube part, then from there screwed the regulator one more carrot (on gravity systems), mark it and put on the locking cap, this way it should provide 80mbar of water tension so there is no need to keep readjusting and you can leave it that way between runs. I use the Tropf max version expecting to keep the bottom of the 25L pots not so moist since 8 days later of the only watering done the moisture is still at 56mbar, looks like it will take some time to start dripping on. Meanwhile I'll keep an eye on the top moisture and if needed just hand water few mililiters a couple inches from the stems. D7. Today I received the missing parts from Blumat and this is the last day of the first week! I think they are looking good despite the little curled up tips from fifth day at 24h but lighting schedule is already changed down to 20h since fifth day midnight. Now they are 6 cm tall and look like they want to start vegging, tomorrow I'll start to daily increase DLI progressively until achieve 16 DLI by the end of the week. The lazy one seems to be doing it, very lazy but growing a little bit every day 💪

Ho aspettato un settimana in più per avere piante circa della solita altezza,le indica si sa che sono più lente in veg,sono pronto per il flip 12/12 😈✌️🏿

Hello guys, Here I am again to present you a new run, still with the best leds of the market nevertheless as I changed my growing space from 120x120 to 150x150. So I had to update the material inside... I will run with 3 EVO 5-150 lamps of 320W or 960W with Bluetooth dimmers. For the Hydro system, it will be the V-SYSTEM from Alienhydroponics. In fertilizers I am always with Advanced Nutrients. I work with osmosis water. Currently, 4 clones took on 4. Once the roots are ready, I will transfer the cuttings from the propagator to the V-SYSTEM. ------------------------ since the 16/08, when I transplanted the plants in the RDWC system, I noticed some points that I will mention below and correct next time. 1. The cuttings are too small, allow enough time so that I can completely fill my pots with clay balls. 2. Cut out the bottom of the pots from the cuttings. 3. 3/4 of the cuttings are touching the water, so one is late. Next time when transplanting, add more water, up to the basket in order to immerse all the plants and not to create a difference between each one, consequence now I have 3 that are ready to explode and one that will struggle behind, problem corrected today by increasing the volume of water. 4. The b-52 is a real pain in the ass in RDWC, you have to clean the 2 filters almost every day, with this new soup I'm testing without and I think I'll continue like this just with the base sensi grow A and B, as I use Root rot X, I won't use voodoo juice since all the bacteria would be killed. 5. Use of Voodoo Juice is useless if using Root Rot X which will kill the bacteria. I don't know why but when I transplanted in the RDWC, I put my set up in growth mode, except that the plants were not ready for it, moreover, I made a FIM on each. So I lost some days, these last days I went back to a ppdf of 150, now that my roots touch the water, I declare growth 0 on 22/08, I will do between 21 and 28 days of growth. And as my roots are doing well and touching the water I'll go to a PPFD of 300 ++

เป็นสายพันธุ์ที่ดีครับ

07/05: made LST and Defolation New res EC: 1,13 PH: 5,8 I'm only adding PH- for now.. PH usally raise and EC remain constant Installed carbon filter and an additional air extractor

10 September Harvest - see pictures. While some growers leave the plant whole when they cut, I do not. It is a personal preference and situational convenience if your a home grower. I chose to cut large, long branches, and remove any whole water leaves, as long as it doesn’t interfere with the bud formation. I don’t trim yet. This is done for a few of reasons: 1) It’s my last good close-up look at her until another 5 days or more, 2) I don’t want wet leaves drying on my buds if I can help it, and 3) I occasionally like being able to shine a small LED flashlight on the flowers while its drying. Mold is our greatest problem as growers, it can destroy a beautiful grow right up until the end process. Then I hang it in a dark closet, provide circulation and ventilation. Light and heat, anything above 80 degrees F, will start a break down in cannabinoids during the dry, it is ideal to stay away from both. I’m fortunate that a humidity level of 50- 55% and temperature of 65-70 degrees F is fairly consistent and easy to maintain. Anything below 60 degree F will prevent the adequate drying out of chlorophyll. Almost all my flower routinely take 5-7 days, some a little longer, to properly dry out. 15 September Trim - see pictures. First you’ll notice the buds have shrunk up to half their original size. This is just a fact that we growers have to deal with. Due to evaporation without uptake of water, it takes about 3 days for the chlorophyll to dry up, then slowly go through a chemical change. Along with the leaves, cannabinoids also begin a chemical change after 3 days called decarboxylation. A slow process where the THC level increases while curing. You want the leaf to be dry so they can be hand trimmed easily, but you do not want that bud so dry that it starts to fall apart in your hand. Try to handle carefully by the main stem to avoid touching the bud all together. A lot of these cut leaves will be covered with trichomes, good for making oils, or other products, it’s an option worth looking into keeping it. After trimming, I do separate a few premium flowers for my first smoq. Then loosely fill wide mouth quart mason jars with about 1 oz/28 gr of product per jar. I seal the lids for a few hours to determine what relative humidity they are at, see hygrometer pic, before making a decision to put in a 62% humidity control pack of my choice or to wait, then place in secure in a cool dark place with stable humidity and temperature. It is very important to then observe/burp or exchange the air as needed, up to several times a day, until 62% rh is achieved. Once your close to to your mark, put in your desired RH level control terpene shield. If you have a problem getting there: 1) it has dried out too much, no real solution, try to put several large cut stems left over from harvest into the jars with the buds to try and increase humidty, 2) it has not dried out enough, in this case no problem, just remove and dry out a little more. This is also a personal choice, some people like it drier in the 50% plus range. Whatever you do, research and preserve. At that time burping is no longer required. Cannabis will reach its peak potency potential at about 40 or so days into the cure. The finished product should be a perfect grind when cured correctly without clogging up your grinder, this could take a month. Now that I’ve said that, I’m sure someone has grown something that they have not been able to grind. It can remain in this state for an easy 6 months with little change, locking in all the terpenes and potencies. All you need to do is occasionally check the product to ensure there are no molds. If your grow/harvest/cure techniques are good this should not be an issue. It would not be uncommon to find many cannabis strains will last, with small degradable change, for up to one year after being stored this way. Using an airtight glass container, controlled relative humidity, maintained low temperature, and kept in darkness will equal maximum shelf life. Always avoid direct sunlight and temperatures above 80 degrees F. The reasons I’ve ultimately chosen Deep Water Culture as a grow medium. Each has their own pros and cons indeed. I found the most efficient, less maintenance and ideal solution for my situation was DWC. Burdens to overcome depend on size up set-up; initial equipment cost, size of containers, ph monitors, air pumps, type of water to use-reverse osmosis, RO cost/set-up/maintenance, ways to transfer/change water and nutrients, what nutrients to use and schedules, takes several grows to learn and understand, a 1 year learning curv, easy to nutrient burn. The Benefits of growing in water; no dirt, no bugs, no diseases, rare nutrient deficiencies/toxicities, steady and rapid growth that enables the plant to reach its genetic potential. After harvest, there is about a 1 hour equipment cleanup, sterilization and turn around process before replanting. Cannabis will perform in so many different ways and mediums, no one way is the best and the best way is the one you are using, right. Chose what works for you in the long run. There will always be an initial cost in set-up. My advice if one were in need to cut corners, I would not recommend cheap lights. This single factor is the most critical, afford for the best. The notion that organic and water has a different taste, flavor and potency effect is absolutely debatable. The more we learn the better we grow and experience is always the best teacher. This is what works for me and my methods of growing in general from beginning to end. A BIG “Thank You” to everyone who stopped by to take a look. My next diary will start at the beginning of October 2023 with a Forbidden Runtz Auto. There will be minor differences during the grow. I enjoy Auto strains simply by what can be achieved in a short time. No matter the strain they will unveil one thing in common, the demand for attention. Many times over it is the anecdotal gardener that surmount plant scientist. Last should I mention, do not forget to stop and enjoy the fruits of your labour...

So this week I added nutrients for the flowering stage. I gave her a little trim as well as added her netting. I flipped her on last Sunday PP

Not much to say, just collected the seeds fresh from the dried mom as I trim her to begin curing. Happy growing to all and thanks for checking out my grows 👍🏾👍🏾

They all doin pretty good, leaves are a little too yellow for my liking at this point I should have added some grow to the mix but they will be fine I think. This one had a medium stretch, seems to have nice balance in its bud size. REMEMBER , IF YOUR SHOPPING FOR GEAR YOU CAN USE THE CODE “BANGDANG” FOR 10% OFF YOUR ENTIRE PURCHASE FROM ANY OF THE FOLLOWING COMPANIES. @greenbuzzliquids @rainscience_growbags @gorilla_grow_tent @growlightscience.led NEW* @Rocbudinc Seeds on his website * *****Gorilla grow tent discounts extend to all companies affiliated with grow strong industries which include..***** @super.closet Lotus Nutrients Kind LED grow lights

~ AirCube Active Oxygen Ebb/Flow System sponsored by GrowAce, featuring Tropicana Cookies by FastBuds ~ Well guy's and gal's here we go again on another exciting Autoflower run together! This time will be different as I will be doing a 'Hydroponic' run utilizing the AirCube Active Oxygen Ebb/Flow System by GrowAce, who were kind enough to sponsor me for this run, so it should be interesting to see what results I get and have some fun along the way! •Let me first tell you about this 6 Pot Ebb/Flow system from GrowAce: "The AirCube system is the one and only Ebb & Flow grow system on the market that combines the benefits of air pruning with a fully automated Ebb+Flow system! With the AirCube's proprietary fabric pot in bucket design, this system is guaranteed to outgrow any other Ebb + Flow system on the market. The results speak for themselves- grow MASSIVE roots that result in MASSIVE fruits! Air Pruning- Air Pruning only happens with fabric pots. As the roots reach the fabric walls of the pot, they penetrate and grow into the breathable fabric. Once penetrated, the roots are exposed to air, which causes the tips of the root to dehydrate and naturally prune themselves. This natural pruning process forces the roots to grow tons of lateral fibrous feeder roots. This results in a plant that utilizes the entire root zone and fills the entire pot with tons of roots. These fibrous feeder roots are incredibly effective in uptaking water and nutrients, resulting in a plant that grows healthier and more vigorously! Oxygen Benefits- Without oxygen, nutrient absorption cannot occur. On a molecular level, oxygen is needed to transmit nutrients across the cell walls and into the roots of a plant. With the AirCube's proprietary bottom lifted draining design, the system actively draws all of the water out of the bucket pulls vital oxygen into the root zone. Maximum Versatility with Any Grow Medium: The AirCube System is the only system on the market that allows you to use any growing medium you like. Use coco coir, soil, peat moss, perlite, vermiculite, hydroton, rockwool or any other medium you wish! This system is the most versatile Ebb and Flow bucket system in today's hydroponics industry. Temperature Control- with the fabric pots constructed with highly porous polypropylene fabric, heat dissipates easily and effectively. Unlike standard plastic pots, heat isn't trapped in the root zone. Heat in standard plastic containers can reach temperatures of up to 125 degrees. When this type of heat is trapped and unable to escape, it can damage your plant's health and limit the potential of your harvest. Growing in the AirCube System, plant roots grow cooler, healthier, and more vigorous. Largest Pots in its Class- this system features 5 Gallon grow buckets, the largest pot size of any other ebb and flow hydroponic system in the market. Modular and Expandable- start with 6 grow buckets and expand up to 36 grow buckets with the optional 105 gallons PopTank reservoir!" For my medium and nutrients I decided to also switch things up from my regular Organic runs, going with Plagron Nutrients and Root Royale 70/30 Coco/Perlite. When filling the fabric pots with medium, I first added just under a gallon of horticulture perlite from Nor-Cal as a base layer to ensure good drainage and then filled the remainder with the Root Royale. •Now for the outstanding, award winning strain from my friends at FastBuds... Tropicana Cookies Auto: I'll be running Tropicana Cookies Autoflower which is a 60/40 Indica/Sativa Hybrid. "Tropicana Cookies Auto is the perfect variety for growers of all levels, especially beginners as this strain performs very well outdoors and indoors, and can produce up to 500 gr/m2 in 56-63 days without needing extra maintenance. Reaching up to 110 cm, this strain grows fairly tall with medium-sized branching, showing its mixed heritage. Definitely the right choice for those with a high tolerance looking to get their hands on the strongest autoflowers out there. You can expect an extremely powerful and long-lasting high that’ll boost your mood and give you that extra push you need to start your days on the right foot. This variety offers the whole range of citrus and woody flavors with a strong candy-sweet background that will keep you coming back for more and more."* *References: GrowAce.com, 2fast4buds.com ______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ The Setup: • AC Infinity 4x4 tent •AC Infinity Cloudline T6 Exhaust Fan w/ Controller 67 •HLG 650R w/UVA Bar *** For some reason GD does NOT have a listing for the USA version of the 650R so I selected the closest match to it. •AirCube Active Oxygen Ebb/Flow 6 pot System •DL Wholesale Root Royale Coco Lite 70/30 coco/perlite •TrolMaster Hydro-X Controller for light •AutoPilot APC8200 co2 controller fed by a 50# tank •16" Hurricane oscillating fan and 8" floor fan •Tent cooling via filtered outside air delivered by AC Infinity Cloudline T6 fan •BlueLab instruments: PH Pen and Truncheon Nutrient Meter ______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ Weekly Updates: 10/29- Here we go into the fifth week from seed for the FastBuds Tropicana Cookies and the #2 and #3 are just starting to flower! The #1 is just starting to show signs of pre-flower, so she'll not be very far behind the other two. Today I adjusted the feeding schedule for the Tropicana Cookies to six feeds a day. The first feed begins two hours after 'lights on', then every three hours until 'lights off' which the girls should enjoy! I am currently keeping the nutrient level to 800ppm, and have begun to introduce Plagron's Green Sensation @ 2ml/g. I'm curious as to how much, if any, stretch these girls will have... I guess time will tell. 10/31- 👻HAPPY HALLOWEED! 🎃 11/2- The Tropicana Cookies are all looking really good now. The #2 and #3 are beginning to flower, the #1 should be showing any day now. The #2 is still a bit paler than the others, but I have noticed a steady improvement in her color. I have also used some horticulture wire to do some LST on #2 and #3 to spread out their numerous side branches exposing them to more light. Our weather has finally cooled off now allowing me to keep better control over the tent temperatures. I now have the HLG 650R turned up to 100%, and hung 28" above canopy. The Tropicana Cookies remain on six 15min feeds a day, and I have adjusted the nutrient level to 900ppm @ 74℉, while maintaining a ph range of 5.9-6.4. 11/4- Well there's five weeks of growth, and one week of flower for the FastBuds Tropicana Cookies! They are really digging the GrowAce AirCube system, and I must say so am I! I'm getting used to the routine now of checking the reservoir, cleaning/refilling, and maintaining the environmental s which is showing in the condition of the plants. Hopefully, things will continue on this track and the end results will be epic! See you next week fam!😎🙏💚💚💚 💚 Thank you for checking out my passion in life! Please visit as often as you wish and I hope you enjoy this journey as much as I know I will! Grow what you love, Love what you grow!💚

This outside AK Auto is doing extremely well in the eastern Canada climate gotten a little rain but lots of hight heat and humidity. Very healthy girl no stress