Buds are forming well. Trichomes are also developing.

All feeds with nutes use either a whole ratio or combination of "Veg Mix" and "Bloom Mix"concentrates DILUTED in water until a total ppm of add in is reached using a (Total Dissolved Solids)TDS Meter measured in PPM (parts per million). The "Veg Mix" concentrate will eventually be added in smaller ratios and "Bloom Mix" concentrate what will eventually replace the "Veg Mix" concentrate entirely with the ppm and ratios listed when I feed. Veg mix recipe is on week 3. Bloom Mix recipe is on week 5. Day 70/0 Flipped to 12/12 - increased ppfd by 100 and worked to stabilize temps/humidity with new gear. I used 15 minutes of IR light before main lights and then 30 minutes of UV light at mid day and will still use 15 minutes of IR light after main light are out. I plan to increase the time of UV lights to a max of 2.5 hours per day mid day but for now Im easing her into the treatments. Watered with 1.12 gallons of 6.3ph de-chlorinated tap water, used 50ppm of veg mix and 50ppm of bloom mix in the water. VPD is mostly steady 74F/65%RH/33%ILV Day 71/1 tested and calibrated my meter, tested the top soil 1 day after feed for ph - tested 4 times for an avg of 6.48 Trimmed brown leaves and did some HST/LST training/binding. Took control pics for UV treatments of 15 minutes per day. Will monitor and increase weekly it she holds up okay. Still doin 15 minutes of IR light before and after lights on/off. PPFD after training was 630 at highest and 540 lowest. VPD was 74F/60%RH/33%ILV Day 72/2 Just a watch today, VPD was 75F/60%RH/setting 4/10 of ILV (about 33% like the last tent) PPFD ranged from 530 to 650. I only used 5 minutes of UV light today as she has a tinge of browning on the tips of a few leaves. Im not cutting it out completely because I still plan to use upto 2.5 hrs by end of flower, so she needs to adjust. Im also still using 15 minutes of IR before and after main light schedule. Her stretch seems to be picking up, from 16 inches 2 days ago to 18 today. Day 73/3 VPD same as yesterday 75F/60%RH/40%ILV PPFD hit 670 at highest and 550 at lowest. Stayed with 5 minutes of UV light and monitored burnt tips from previous days... no spread, so I may add 5 more minutes tomorrow and monitor. 15 minutes of IR before/after main light schedule. Growth continues, another inch in stretch to 19 inches. I turned her slightly because there are still two runted colas that I rather provide more light to. It's been 3 days since last feed and I think with as much growth as she's putting on, I should feed again tomorrow. Im still introducing nutes in lower portions but will add 300ppm and feed about 2 gallons at a 25/75 ratio of veg:bloom mix to see if I can get some run off to measure conditions. Day 74/4 Watered with 2 gallons of 6.4 ph de-chlorinated tap water. I added 300ppm total of 25% Veg/75% Bloom. Starting ppm was 296; ending was 595 and I added a pinch of epsom salt. Poured over the whole base until I got runoff - Since I was so close to the whole 2 gallons, I used it all. I only used the feed water over the roots today as I want her to get the nutes from the soil since the transfer into new soil was so recent. So far VPD is 75F/60%RH/40%ILV. No issues with controls. PPFD was upto 700 at center so I raised the lights to almost 42" from soil - Since the plant is almost 20" that's 22" leaves to light. New PPFD now ranges at 480 to 650 on 70% power. I increased UV time to 10minutes today and took control pics for light burn. I am still using 15 IR before and after main lights. Took some black back picks since I think she's looking good now. Day 75/5 Started the day with evaluation of ph and control pics. Comparisons show no further spread of lock out issues from earlier or light burn of a more recent change. Upto 20 inches before HST/LST today. Meter was tested/calibrated and soil ph was tested 4 times for avg of 6.34 (yesterday's runoff was about 6.35 too) Soil temp is about 66F. Also tested CO2 and got 1050. Room VPD was 74F/60%RH/30%ILV I spread the leaves further apart because I noticed there were two colas not getting as much light and somewhat crowded by the colas near by. So I positioned the larger part of the tomato ring around the limbs extending here out to 32x32 and the used HST/LST to break and bend the center colas inward clockwise (I think I went a bit too hard on one as the others already show a bounce back and now one is still limp-ish (will monitor obviously) But with that the height is now 18" so 32x32x18 - but here's the kicker, I only have a 24x48 tent, so there's a few colas touching the walls and doorway now, so I may have to reconsider the larger ring. New position, new PPFD right?, not exactly, for some reason these settings still gave me range of 480 to 650 as I had yesterday with just a few more of the outer colas have 480 than yesterday. However, there's more light getting lower levels now and I only had to cut 1 leaf. Which is good because I did 15 minutes of UV today with the regular 15 minutes of IR before and after main lights. Day 76/6 VPD is a lil wonky now as humidity is starting to go up in the tent - so I plan to put in the dehumidifier this weekend and just leaving the humidifier off today and tomorrow. Heat seems to also be ticking up - so I reduced the temp on the heater and will monitor. Temps about 75 to 76 - humidity at about 62% as high as 65 though and Im trying to be at or under 60 this week. Increased ILV to 40% I repositioned the fans to hang on the lights while blowing down onto the plant. I tried to make every leaf dance a little. LST seemed to hold up okay - had to reposition a few branches and thinking I may have to build a larger box this weekend since the colas are now pressing the door and back wall. PPFD is between 470 and 700. I used 15 minutes of UV mid day with 15 minutes (30 total) IR before and after main light timers.

Hope you all enjoy the video, but don't share ok it has an uncleared Beatles Song that The good Dr. loves ;-) Peace

back is sore from trim jail, but I got through a half pound in a couple

Washed her roots too before transplanted intoa bigger pot

This plant looks absolutely gorgeous guys, I'm sad for not being able to film this Transplant because my phone just died when I was in the action, so this lady just like all her sisters have been Transplanted on day 39 since planted and I've prepared the 15L pot with the complete biotabs organic line, using 25g of startrex for every 5L of soil, a couple of grams of mycotrex on the transplant hole, and 3 tabs slow release fertilizer (1 tab for every 5L) and then just watered the plant immediately after the transplant with 1ml per liter of orgatrex and 1G per liter of bactrex,

Transplant time! Got these girls into a three gallon container with added mycos and bacteria. My custom mix is coco and perlite with added amendments, worm Castings and purple cow soil. I add dolomite lime on top and mix it in. They got a small watering.

Starting 5th week of flowering. Buds are growing nicely. I increased the neutrients from 3/4 to a gallon to 1 teaspoon per gallon. They are fed every 3rd watering . They each get a gallon of water every 2 days ph balanced twice a week and fed once a week.

Blütewoche 3 Die Blüte ist im Gange! Die Pflanze streckt sich immer noch zaghaft. Insgesamt ist die Pflanze sehr buschig und dicht gewachsen daher muss jetzt entlaubt und aufgeastet werden.Der Düngeplan bleibt unverändert. * Zustand der Pflanze: Mäßiger Blütestretch, schöne Blütenstände. * Wichtige Ereignisse: Zeltwechsel, Lollipoppen * Düngung & Messwerte: * Gießwasser: pH ca. 6,3. Leitwert 1,4 bis 2 S. * Drain: Wir stellen sicher, dass der pH-Wert nicht unter 5,5 und nicht über 6,8 liegt und der Leitwert die +/- 500 S Abweichung einhält. * Anpassungen: Entlauben und Lollipoppen

Thestretch stopped and now after defoliation i let her go stressless

Finally I am getting started with my very first grow after 1 1/2 months of preparation. The Seed got germinated in a Solution of 1ml C²O² and 29ml of Water. Sadly the Seed opened over Night and the Sapling swam in the Solution. I still set the Sapling in the prepared soil mix with Biobizz allmix, Biobizz light mix on the top where the plants sits and 5% Perlite extra. lets see what happens with the plant because I am very curious.

I did not expect such a strong aroma, the plant smells very strong! This week I had a small pruning of the lower leaves, now the main green mass remained at the top, began to grow in volume. Cones began to gain weight, it is already noticeable how the branches became heavy and weighty, fertilizers added 2 times a week in microdoses, the passport indicated that with a stable coverage of 20-4 will grow faster, but I still decided that the whole stage from beginning to end I will spend on 16-8, since I myself assume that this is the most comfortable hours, next week I believe will be the final flowering stage, near Xia Harvest, at the moment all trichomes are transparent and white mustache, my camera unfortunately does not allow for high quality pictures and I can not memorializing it in the photo, in general, I am guided by its past cycle, and I feel that everything will be fine.

Hello growers day 42 in the garden with the blue monster auto 19/7/20 all is well she’s looking really good just keep feeding her when the top is dry and she is loving life just hope this good weather iv been getting holds out for a bit longer so she can beef right up until next week be safe and happy growing ✌️

Finish week 8,5

**Encontrarás la traducción a español al final de la descripción** If you like this week, please hit a like, it costs you nothing! 👊. Thanks in advance 😉! From/Desde: 19/08/19 || To/Hasta: 25/08/19 From day/Desde día: 28 || To day/Hasta día: 34 -----IMAGES & VIDEOS----- P5 - I'm loving this photo, is the first complete cool photo of the AK i've taken. With the structure, the fixing rods with the same length as the diameter of the AirPot, and those beauty rubbered green cables 😍. P8 - I'm feeling that those branches looks too weak, and slim for what's coming. From next week i will use Rinho Skin to see if it can help them to get fat in upcoming weeks and before flora time. I'm also minding to create some branch supports with the 3d printer that will be placed on the LST structure, I need to twist my mind a bit with it. -----WEEK SUMMARY----- Another super heat week. While at home i'm at 34~36º in the street things are worse :(. Also humidity fluctuate from 50~65º. At last I removed those ugly & dangerous cables from the branches and used a rubber covered one. For now i only need to fix her in 4 points, 1 per each main branch, as you can see, at about 13 cm of the main branch. Later i will fix her with another 2 points per branch, one in the border of the pot from inside, and the last one also in the pot's border but outside. This week i removed the first horizontal internode on each main branch, and also removed the branch that grows vertically down from the second internode leaving in place the one that grows totally up. At the end of the week i will fix the SCROG mesh, but it's not going to be permanent until later, or maybe not at all due to dark photography, as if i place the mesh i will not be able to move the plant (i need to think about it). For now, I just need it 3 or 4 days to test it as i never placed this 60x60 mesh before, and also i had to cut the central rods for the mesh. About Alice K. she's growing beauty and healthy, some week ago i found a little white spider that i killed, @time (week 7) I didn't noticed any insect signs more. Also remark that she's standing well those temperatures and some days of very low humidity some hours 35% inside the tent. And also the equitative distribution she's developing. As i said on previous week, i will kill those clones at mid week as i'm going to plant 4 more seeds in a week, and all is going to be too much work 😞to compatibilize it well with my job. -----WATERING CALENDAR----- 23/08/19 (Day 32) - 3,000 ml with all week nutrients @ 1.1 E.C. PH5.8 *****ESPAÑOL***** Por favor, si te gusta esta semana dale un like, no te cuesta nada 👊. ¡Gracias por adelantado 😉! -----IMÁGENES & VÍDEOS----- P5 - Me encanta esta foto, es la primera foto completa guay que hago de la AK. Con la estructura, las barras de aluminio de la medida del tiesto y esos cables cubiertos de goma verde, me empieza a encantar el aspecto de la planta 😍 P8 - Tengo la impresión de que las ramas son demasiado endebles y finas para lo que está por venir. A partir de la semana que viene, usaré Rinho Skin para ver si las puedo ayudar con el engorde antes de que llegue el tiempo de floración. También estoy pensando en crear unos soportes para las ramas con al impresora 3D que irían enganchados a la estructura para LST, necesito darle unas cuantas vueltas a esto último. -----SUMARIO SEMANAL----- Otra semana super calurosa. Mientras que en casa estoy entre los 34~36º en las calles la cosa es mucho peor. También la humedad está un poco loca ya que a diario me fluctua en casa del 50~65º. Al final he quitado esos cables feos y peligrosos de las ramas y he usado un cable con goma en condiciones. Por el momento sólo he tenido que atar la planta a 4 puntos, 1 en cada rama que he dejado, como se puede ver a unos 13 cm del tallo principal. Más adelante usaré otros dos puntos de fijado en el borde del tiesto, uno de ellos en la parte interior y otro por fuera del tiesto. Esta semana he quitado el primer nodo de cada rama y también la rama que crece hacia abajo del segundo nodo, dejando la rama que crece totalmente hacia arriba. Al final de la semana colocaré la malla de SCROG, pero no va a ser de manera permanente, por lo menos hasta más adelante. Voy a empezar a hacer fotografías de fondo oscuro, y el tener la red me va a imposibilitar la tarea ya que debo sacar la planta del armario para las sesiones (necesito pensar en ello). De momento la quiero montar 3 o 4 días para probarla ya que nunca la había montado antes y también tenía que cortar las barras horizontales para la malla. Sobre Alice K. está creciendo super bonita y sana, hace un par de semanas encontré y maté una arañita blanca (Requiescat In Pace), a día de hoy (semana 7) no he visto más signos de insectos. También debo remarcar lo equitativamente que está creciendo y lo bien que soporta las altas temperaturas y la escasa humedad, hay alguna vez que he mirado el higrómetro y estaba al 35% dentro del armario. Como dije en la semana anterior, mataré los clones a media semana, voy a plantar otras 4 semillas la semana que viene y va a ser demasiado curro 😞para compatibilizarlo con mi trabajo. -----CALENDARIO DE RIEGO----- 23/08/19 (Day 32) - 3.000 ml con todos los nutrientes semanales @ 1.1 E.C. PH5.8

Semana sel 2 de septiembre al 8 de septiembre 8 de septiembre, fotos del dia Jueves 5 de septiembre 2024. Se regaron con Floralicius plus adicionado con Hidrol-pez + vitaminas.

This one is going to be weirdly exciting like all grows… but nothing beats growing strain you know nothing about down to to it’s ID. This is why this diary is dubbed Unknown Strain, and a lot more journals will be dubbed unknown strain. eg. Unknown Strain #1 - these strains are seeds I’ve collected and forgot to catalogue Unknown Strain (dealer/grow name #1) - I have it this way,to indicate where or from whom did I get the seed, but failed to get the accurate information regarding the strain. Alike this particular diary. I received seeds from my friend saplug16.20_exotic_genetics. Check out his work on instagram, his my mentor in growing. But I go overboard when it comes to growing. Ever since I’ve seen YouTube videos of growers growing weed plants like bonsais, I started growing my plants like I am growing actual bonsais, LST them in shapes and size while using defoliation and topping to achieve aesthetics. This type of growing is not focused on yield more for the hobbyist who grows for themselves and close friends. But I want to see if I can get more yield with this type of growing bud.

Week#7 Baby Boom/ Kannabia Seeds Week#7 Dec.9th-16th Baby Boom Plant stretched to 25 inches tall. She is starting to fill in her multiple buds sites.