Recommended
Likes
Comments
Share
Everything is going well with the lady's, no issues so far💪 Gonna put them in flower on the 25th and gonna start adding bud-ignitor to give them a litle kick under the 🍑 Rock on growmies
Likes
18
Share
@Hawkbo
Follow
Autos are just starting to flower the photos are dying for some bigger pots. I've been trying to bring up the overall plant health in general since moving everything to a basement the temps are a little lower than ideal. I had a space heater delivered today and monitored the temps but they only went up to around 78°f I want it to be atleast 82°f ideally 85. The heater uses 1500 watt and only increased it about 2 or 3°. I dont think it's worth the extra cost for such little boost. I'm thinking about returning the heater and throwing a 1000w hps in one of the other tents and see if that will raise it anymore. Especially with LED and co2 higher temps would be very beneficial in veg and early flower but the room is so big its gunna be tough to pull off without killing me on electric costs. Any suggestions are welcome. I know this room does decent in flower but I havnt done much veg work down here and I'll have some autos growing this round so it's important I get it up.
Likes
1
Share
Hello Growers & Tokers! Roots, roots, roots. At the beginning of the week they got transplanted into their final pot, 11L fabric. Medium used was Light Mix from BioBizz. Synergy from Grotek nutrients was blended in the medium to help out the roots. They were a bit down after transplanting but by the end of the week they were doing better. I'll leave her be for a week then I'll be topping to spread that canopy out and have loads of colas. Or at least that's the idea but two of them seem to be growing faster than the others so I might have to die those tops down. Take care out there and happy growing!
Likes
43
Share
Continuiamo solo con overdrive per un altra settimana continuando a controllare sempre i tricomi, aspettando che diventino lattiginosi per cambiare soluzione e far girare l'impianto gli ultimi 7 - 10 gg con solo acqua osmotica a ph 6 per il flush prima di raccolt
Likes
19
Share
@valiotoro
Follow
Hello everyone week 2 has passed for this Cherry Cola auto by Fast Buds 😎 this plant is doing very well growing at fast pace and with a beautiful green colour on the leaves. Topping & LST for my girl 😎 wish you all happy growing!
Likes
3
Share
So I’ve over watered them like a idoit and then to top it off the girl on the right all her bottom leaves went droopy and didn’t look so strong so I cut them of , also I’ve noticed some yellowing on the tips of the leaves from the girl on the left but I think that’s due to over watering , anyway I’ve done from watering everyday to when top of the coco is dry nutes are the same just gone from feeding every day to every other day but overall that’s the end of week 3 and I’m still impressed on how there looking AS ALWAYS ANY ADVICE WOULD BE AMAZING
Processing
Likes
10
Share
Desgraciadamente el cultivo se quedó estancado en altura y demás. Estoy decepcionado pero la próxima saldrá mejor, no haré tantas podas y quizás cultive automáticas para cosechar rápido
Likes
5
Share
Likes
14
Share
@Smokwiri
Follow
Welcome to week 5 of veg. of the Royal queen seeds Royal Gorilla pre-flowering hairs visible.... some stretching... but flowering did not set completely yet I'm starting to like the size of this Royal Gorilla, hope the side branches will be alike.
Likes
25
Share
@nerdz
Follow
22 to 28 D23 Noticed a huge growth spurt between yesterday and today. I guess that bottom feed really made the roots go wild. Will transplant into the autopots at the end of the week. I am not going to use the 7gallon pots anymore, it's way too much coco. I am moving down to 3.7gal pots which will be easier for the roots to reach the bottom and give me better growth. 720ppm @ 5.8 full veg this week bottom feed. They l-o-v-e it. I already see the benefits to growing photos. So much less stressful and guarantees a full tent. I wish I tried it sooner! D24 Feed 700ppm Removed a couple big fans from each plant D26 LST and defol Moved lights closer. 18" @ 160w
Likes
127
Share
@DreamIT
Follow
🎃👹👽MONSTERCROPPING RED MANDARINE 👽👹🎃 ____________________________________________________________________________________________ 💀 5.2 ... 💀 6.2 ... 💀 7.2 All regular, Today we add the latest product from hesi to fertilization and wait for the last few weeks, yeah !!! 💀 8.2 💀 9.2 💀 10.2 I love this plant 😍 💀 11.2 _______________________________________________________________________________________________________ 📜👀 A look at the details of what I'm growing 👀📜 🍊💚 Red Mandarine F1 🍊💚 by 🌱🍭 Sweet Seeds 🍭🌱 📋 Details ⚧ Gender ▪️ Feminised ➰ Genes ▪️ 55% Indica / 45% Sativa 🎄 Genetics ▪️ Red Poison Auto (SWS39) хCalifornia Orange x Skunk hybrid) 🚜Harvest ▪️ 400 - 500 g / m² 🌷Flowering ▪️ 49 - 63 days ✨THC ▪️ 16% ✅CBD ▪️ 0,2% 🏡Room Type ▪️ Indoor 🌄Room Type ▪️ Outdoor 🕋Room Type ▪️ N/D 🎂Release Year ▪️ 2019 __________________________________________________________________________ 👀📷🥇 Follow the best photos on instagram 🥇📷👀 https://www.instagram.com/dreamit420/ 🔻🔻🔻Leave a comment with your opinions if you pass by here🔻🔻🔻 🤟🤗💚Thanks and Enjoy growth 💚🤗🤟
Likes
5
Share
@hilfa
Follow
Defoliated bottom parts of plants and lower growth. It's fairly evident now that the CBDiesel isn't going to produce much. The fan leaves and bud sites are tiny in comparison to the other two strains. Roots have become completely entangled and almost reach the perimeter of reservoir. Continued to tuck taller growth back under trellis to create even canopy. Foliar fed 3 times throughout week with half strength solution. Added pH balanced ice cubes 3 times throughout week to boost oxygenation Humidity way too high, need to address this fast.
Likes
31
Share
@Neo09
Follow
We just build +1 Room, about 9Sq meter with 2000w HPS. We decide, cos we see a lot more of potence by this genetic i have to tell now, ~less is more~ ..if i talk about ammount pro sqM... As well we gonna change all small 6L pots for 11L. Where i see our reserve is, that we need to cut much more, of lower level‘s „bat‘s“ in VEG.. ⚠️ actually i know: „dont touch girl in bloom“ , but it was necesary last week.. really necessry to cut all that shit stuff on „bottom“ ... 330 girls on 16m2 in 6L & 11L pots
Likes
12
Share
@chronicon
Follow
i have been flushing since friday and this coming wednesday it will go into an extended period of darkness
Likes
15
Share
@Rinna
Follow
I would have let her go for another week but the other plant was more than done and I had no other drying space left. Amazing grow, should be a solid harvest and the buds smell and looks amazing. Very sweet, creamy and gassy artificial cherry terps. Very excited how they smell and taste after drying and curing!
Processing
Likes
7
Share
Plant is looking good 😊, fully recovered from defoliation, I set the lights closer, switched them to 12h of light per day, and did some spraying to control pests with neem oil and organic Marseille soap, everything good so far . Can't wait to see the flowers forming. I used a net to open up the branches, and get more colas, it worked but I think stressed out the plant a bit and the fact that I did it in the flowering period didn't helped, so next time I'll do it way before, but I recently bought the net so.. anyway I kept the net on for three days, and now I decided to remove it cause was getting me lot of troubles accessing the setup in general, watering, basically made impossible any movement inside the tent. Still did is thing and now I have not the best even canopy but many more top colas for sure. Please give me any advice, I've noticed it is drying out lot faster, humidity is still at 58% but I believe the roots are much more developed. I will leave home for 2 or 3 weeks, my sister will have the duty to just water, can't ask her more, hope for the best. So updates will be very rare but she'll take pictures for me and for us :D .
Likes
8
Share
@4GLOW20
Follow
It was last week with nutrients so flush week started. (microbes & figg molasses) Upper buds turning to purple colour. She will be multicolour😍
Likes
14
Share
ALL THE PHOTOPERIODS ARE IN THE 8X8 NOW. DID SOME MAJOR DEFOLIATION BECAUSE THEY ARE TOO BIG NOW. THEY ARE SWITCHED TO FLOWER AND THE STRIVE NUTRIENTS IS INSANE.. BEST FERTILIZER PRODUCTS EVER MADE. I USED IT 4 TIMES IN 13 DAYS AT FULL STRENGTH AND THERE IS NO NUTRIENT BURN AT ALL AND THEY EXPLODED. AND I HAD A FEW THAT WERE TURNING YELLOW, I THOUGHT IT WAS ROOTBOUND OR CALMAG DEFICIENCY BUT THE STRIVE NUTRIENTS BROUGHT THEM BACK AND THEY ARE SUPER HEALTHY AGAIN.... ATTENTION GROWERS:::::: YOU MUST TRY STRIVE NUTRIENTS. BY FAR THE BEST FERTILIZER PRODUCTS EVER.. I PROMISE YOU THAT AND IF YOU USE IT YOU WILL NEVER USE ANYTHING ELSE FOR EVERYTHING MARS HYDRO VISIT: www.mars-hydro.com www.marshydroled.ca PROMO CODE: rocknroll VISIT THE ALIEXPRESS STORE: @marshydro_aliexpress Instagram: @marshydropenny https://youtube.com/channel/UChU5ZWwNi-DvnO3oWVU3ceA (NEW) STRIVE NUTRIENTS 💪 https://strivenutrients.com/ Thanks for taking the time to read and check out my diary🤜🤛 FC-E6500 LED GROW LIGHT: FC-E6500 grow light with 3978pcs OSRAM BridgeLux Diodes & Moso Driver, market-leading PPF 2.7 µmol/J, Max 2.5g yield/watt with 30% higher Average PPE, more cost-effective when compared to same style type lights. Only consumes 650W, perfectly cover 5x5ft (personal), 4x4ft (commercial) grow space. Innovative Precise Uniform Lighting-Built-in removable bars interval & dimmability enable the exact & dynamic PPFD control over each of the plant growing stages, FC-E6500 detachable bars deliverSuperior Heat Dissipation: Real Aluminum heatsink together with 6 slim profile passive cooled bars (THINNER & LARGER surface) and detachable Meanwell Driver, create less heat. save 50% hydro than other old grow lights! Driver can be mounted remotely on the side of a grow tent/rack or on an adjacent wall to remove heat from grow space. Full Spectrum UV IR LED: With Yield Max spectrum (660nm Osram enhanced Deep Red,2800k-5000k,730-740nm IR,380-410nm UV LEDs), Average PPFD the FC-E6500 LED grow lamp enables cultivators to produce BIG FAT Dense Buds, perfect for full-cycle hydroponic, soil, grow tent/grow room. Dimmable Commercial Grow Light: Cost-efficient, easy dimming & daisy chain With a max up to 20 lights, IP65 Waterproof, master light easily controls the rest. Perfect for commercial & home horticulture. FC4800 LED GROW LIGHT: GET THE MAX FROM MARS👍: Welcome one of  the newest members of the Mars Hydro family🤜🤛🤘. The Mars Hydro FC 4800 480W LED Grow Light can accommodate up to a 4' x 4' area for flowering. It has OVER 2000 LED chips consisting of the best selling Samsung LM301B diodes which has a Luminous Efficacy of: 220 lm/W 0.2 W, 3 V mid power, Osram 660nm Diodes, Infrared light and UV LIGHT👍. It boasts the incredible efficiency of 2.8 µmol/J, maximum 2.5gram yield per watt with 30% higher Average PPFD. This High-intensity spectrum is beneficial for plants at all stages - from veg to bloom, and creates Big dense Buds👍. achieve 50% higher yields & quality compared with the old lights! Only consumes 480W for 4x4ft personal grows, and 3x3ft for commerical grow. It comes with a dimmer and daisy chain function with a  maximum of up to 15 lights, the master light controls the rest👍. Wide 6-bar design offers even & wide canopy coverage and can maximizes your grow space. slim 180° FOLDABLE DESIGN... YES I SAID FOLDABLE🤘🤣 , making it compact and easy to install, it's IP65 WATERPROOF and will give you no worries while growing in a humid environment and makes it a flexible high performance commercial grow light for enormous  SUPER FROSTY yields.😛😛😛. MARS GETS EM FROSTY BOYS👍 AWESOME HEAT DISSIPATION: The Low energy consumption FC4800 growing light has 6 passive-cooled bars and an aluminum heat-sink a removable driver  you can upgrade later or have it outside your tent. with zero noise  you can save up to 50% in your electricity bill compared to HID's or HPS lights! It also has a removable driver so you can upgrade it in the future or have it outside your grow space for better heat control in your growroom👍 UPGRADED FULL SPECTRUM: Yield Max Spectrum with enhanced red (Top-Bin Samsung 3000k-5000knm, Osram 660nm Deep Red), speed up blooming & fruiting, perfectly suited for full-cycle growing. The FC4800 LED grow lamp was born for Big Buds, perfect for commercial, grow tent, grow room, hydroponics, and all soil grows.👍 THE BEST SAMSUNG DIODES: THE FC4800 has Top Bin genuine Samsung Osram Diodes, combined with remarkable 2.8 µmol/J Efficacy, 30% higher Average PPFD, 50% less energy consumption, to maximize your yields. They give you a TRUSTED 3 years warranty 100% Satisfactory guaranteed!!! TSW2000 LED GROW LIGHT: INCREASE YIELD AND CROP QUALITY WITH MARS HYDRO LED GROW LIGHTS: NEWEST SMD LED technology provides the highest PAR/LUMEN output (1122umol@18") and can make you get 30% higher yield compared to OLD blurple led lights.  Max 2.5g yield per wattage and achieve maximum quality and quantity, much better than traditional HPS grow systems LOW ENERGY CONSUMPTION LED GROW LIGHT: Consuming only 300W true output with 684 LEDS! It saves up to 50% energy than other led grow lights. Perfect for 3.5x3.5ft bloom stage, 4x4ft veg stage. Over 90% light energy can be absorbed by plants, it will have higher intensity in a MARS HYDRO grow tent with diamond design mylar, or by crossing over using multiple TSW2000 HIGH EFFICIENCY FULL SPECTRUM INDOOR GROW: 3000K 5000K and IR 660nm 760nm RED, makes it close to natural light, highly engineered to provide improved growing performance for plants at all stages of growing, rapid plant response from seed to flower; Uniform and wide-beam light distribution for your plant's optimal growth 8x8 1680D GROW TENT The MARS HYDRO 8x8 Grow Tent interior is made of a unique diamond design mylar which is highly reflective. (Other companies mylar and reflective rate is as low as 50%, and it won't provide efficient light. They use thick 1680D oxford canvas, and being double stitched, it is tear proof and perfect for locking in the light. Their grow tent keeps 100% of the light inside the tent and helps your plants absorb more light. EXTRA-THICK material means No light leaks or rips at all.👍 Strong Stable metal corner adapters and poles are the trustful supporters of the tent. It's very sturdy, neither rusting or paint flaking off. quick and easy tool-free setup. They use heavy-duty metal zippers, with double layer black lining, by far the best on the market which creates a light-proof seal. The Easy observation windows are made by double layers of cloth. Observe the growing conditions of your plants without opening the tent and avoid disturbing your plants. The observation windows also serves to dissipate heat and ventilate the air. The tent includes 2 removable waterproof floor trays to hold soil and water. The removable tray can be taken out to wash easily. They guarantee the grow tents are easy to install even if you've never done something like this before. Clear Instructions and no tools needed! They also offer 30-day unconditional refunds for quality problems. Just contact their friendly 24 hours customer service 👍
Likes
8
Share
Hello Diary, Milky Way F1 is the most impressive of the three on the farm, at least for me. It is the tallest, 54 cm, with a beautifully pronounced main cola and branches filled with flowers. She is so beautiful. The leaves are of a healthy green color, the flowers are large and cover the entire ends of the branches. The smell has become more intense, which gives me special pleasure when I open the grow box. Watering has become more frequent, every three days each plant on the Farm receives about 2.5 liters of water. I continue adding Bio Flowering Booster and Easy Bloom tablets. Conditions on the farm are good. The temperature is around 28 degrees, while the humidity is around 45%. Here's what it looked like last week. 06/06/2023 - Day 38. Watering. I added all three components from the Bio Flowering Booster. pH I lowered it to 6.0. Each plant received about 2.5 liters of water. 09/06/2023 - Day 41. Watering. This time I put one Easy Bloom tablet in 7 liters of water and watered all three plants on the Farm with that amount. 10/06/2023 - Day 42. End of the sixth week. I photographed the plants and removed three or four yellow leaves. Milky Way F1 - 54 cm That's all for this week, thank you all for your support and see you soon.
Likes
5
Share
@RatmanJR
Follow
Chopped Wednesday the 11th. Trimmed and began curing the 21st. 4oz of super dense sticky bud. 1 pound of high grade trim and 2 oz of low grade trim. This plant was truly strange the places it chose to grow Trichomes. Stay tuned because I will be making hash with the high grade trim. Also will be uploading smoke score in two weeks Thank you to anyone who followed and god bless!