Been a good ride for my first plant

Transplanted from solo cup to 8lr pot

Week 26 for 9lb Hammer F2 One of the plants is really struggling to keep its on bud weight up, so hopefully i don't get any broken branches 😅 The buds are frosty but they are so skinny. I don't have any info to go off so not sure if she will be bulking up or not.

A-Week 9-(Day 67) B&C-Week 9-(Day 63) A- Loving life, she is fattening up, easily 3-4 inch round buds, about 8-12 inches long circling the plant. Lots of little nugs filling in the middle 🤩Tricomes are multiplying daily, still almost 50% clear, 40% milky, and 10% amber or so. Couple of weeks left, gotta keep air flow high and RH low with those dense buds 😎💨 B- After looking back on last weeks photos, she has really started to thicken up. She has big calyxes, and are stacking nicely. Tops on tops for this one. Her LST and topping created a very dense canopy, similar to A, but B stretched a little more. C-Done her stretching, she is now focusing on bud building. She is stacking nicely, and I said it last week, I’m pretty sure she will be the biggest producer if she fills in as thick as her sisters are 👀💥 No issues, no pests, not even Gnats. A tip I got from WTTGT, Woooooooooh! Was to store your soil/medium near the exhaust of your tent so it always has dry warm air blowing on it. I have not had any issues with pests since doing this before starting this run, and then adding another to the mix mid-run(my GG#4) has had no issues. The 975 ppm seems to be their sweet spot, I don’t want to push it as it has been almost uneventful with regards to issues or deficiencies. I’m very happy with the Indo nutrients line, and the addition of the Sensi CalMag xtra together have made this run super easy, considering Autoflowers are far more finicky than photo periods. The differences between each are drastic, topping and LST can be real space savers for those with small gardens, but clearly the un-topped, un-trained pheno is thriving and will produce fairly well 🌱😎💨 Happy Gardening All 👩‍🌾

Week 10 gonna flip in a few🌺 but first some defol and lollipoping.

Bienvenidos cultivadores de marihuana clandestinos, y también, a los que tienen la fortuna de no serlo!🖐️👨‍🌾 Tercera semana desde el paso al horario de floración 12/12h, la planta ha dejado de estirarse, ahora toda la energía está en los brotes florales que asoman por doquier... a jugar! Días fríos y húmedos, las plantas lo notan disminuyendo el consumo de agua (metabolismo), pero hasta ahora todas aguantan sanas, tengo una buena ventilación y extracción de aire en la carpa de cultivo. Lo que menos me gusta de la etapa de floración es que veo poco a las plantas, apenas un momento cuando las luces se encienden a las 22:00h. Esta semana he acabado la instalación de todas las lámparas de la carpa de cultivo, un mix de buenas luces para alumbrar las plantas por todas partes. Al final 450w repartidos en 4 lámparas en el dosel y 3 barras led alumbrando por los laterales. Dos riegos esta semana con mucha energía y toda la gama de macro y micro nutrientes... viva la flor! ============== Info de la cepa Blubonik: https://en.seedfinder.eu/strain-info/Bluebonik/Genehtik_Seeds/ - Cruce de Kootenay Blueberry x Blueberry. - Es una planta de altura media, crecimiento robusto con grandes hojas. - Floración Interior: 60-65 días. - Su efecto es muy fuerte, completamente indico. ============== Hasta pronto... 😋👍 SALUDOS A TODOS!! =================================

🌿 Week 4 — Bushy & Thriving! 🌿 #PermanentMarker #ZamnesiaSeeds The girls really filled out this week — super bushy and thick growth all around! I topped them once and gave them a good defoliation to open things up, as they were getting quite dense. I bumped the feed up slightly to 600 ppm @ pH 6.0, still running the Aptus Clean Program with R.O. Water Conditioner, Regulator, and All-in-One Liquid. 💧 Raised the Future of Grow Black Series 600 a bit to encourage some stretch before the flip. I’ll be adding an under canopy light (UCL) as soon as it arrives, and later this week I’ll set up a trellis/net for support. The plan is to flip them after week 5. So far, they’re looking really nice and healthy — one pheno is even showing a bit of color on the tops already. Excited to see how they develop from here! 🚀

end of week 7 flower | plant is insane | never had such purple plant | strong guava smell | no generic terps | i feel like its going to be a real dessert!| i will keep this running one more week | the plant doesnt really consume co2 anymore

- Water: tap water at 300 PPM, I add 0.6g of Hybrid powder and 0.4g of booster PK+ per liter to reach 950PPM and I adjust the PH to 5.8. I water every 2 days because it is too wet, I water until the water runs out of the pot (to release the nutrients from previous waterings) -Daytime temperature: 21-26°C -Night temperature: 21-23°C -Humidity: 55-80% :/ too high -Lamp: Mars Hydro FC3000. intensity 90% at 35cm from the top leaves -Room: Mars Hydro 100x100x180cm -Extractor: Mars hydro 402 CFM Max. power 3/10 -Substrate : 70% coco, 25% perlite, 5% vermiculite. My instagram : https://www.instagram.com/p/CuMhQ_BsjRP/?utm_source=ig_web_copy_link&igshid=MzRlODBiNWFlZA== Looking for MarsHydro equipment for your crop? 🔥 You can use my promo codes! 🙏😻 3% off with "houstone3" for: TS LED Grow Light, Tent, Ventilation 5% off with "houstone5" for: FC&FC-E&SP LED Grow Lights; Grow Tent Kits https://www.mars-hydro.com/?acc=hou-stone

🍼Greenhouse Feeding BioGrow & Bio Enhancer ⛺️MARSHYDRO The ⛺️ has a small door 🚪 on the sides which is useful for mid section groom room work. 🤩 ☀️ MARSHYDRO FC 3000 LED 300W ☀️Also special thanks to VIPERSPECTRA P2000 (200W) & XS2000(240w) LED growlights 🌱 FastBuds 420

Great week, these lemon pies have gotten huge. Had to stop LST awhile ago because ran out of space . If all turns well they will be the biggest Autoflowers I've grown. The pheno type I have is definitely more Sativa leaning

Plant was very hardy and stiff buds thick and dense. I'll update in a few days upon dry. We Did It... Let's groW some mo...

6/6Still trucking along. I'm curious how long of a flowering strain this actually is. She is probably about half way done Come check out the other channels and stuff. Youtubes starting to pop off. Super cool. Instagram is just chilling. The new seedsman community is super cool. Forums are dope as well. Check out the links on my page or just search for AestheticGenetix and I'll probably pop up everywhere

This week we have another big jump in height; they are taller than myself. I gave them more bloom nutrients this week and the daylight is waining fast now. We finally got a considerable amount of rain in my area, that was nice and refreshing for all of us including the plants. I hope that as the light continues to drop off significantly and the nights start to get cool, we will start to see some buds 😎🌱

Broke a branch this week pretty upset about it was a large branch. Other than that everything is going well slight deficiencies here and there just gotta watch and correct them. We should jump into flower here in 3-5 weeks i will do my final trims in roughly 2 weeks 🤙🏻

I came to the conclusion that my issues all stem from the fact that I was doing two things wrong with my watering: 1. Too much (duh) 2. Too fast! I was using a watering can and it is talked about time and time again to use a hand sprayer to ensure even distribution and slow release. It is very challenging with a no till method because I’m impatient and I need to remember that I’m nurturing the living soil, not the plant and this method is far different from my outdoor and hydroponic experience. This weeks schedule looked like this: 12/27: Water and 1/4cup of kashi per plant top dressed 12/28: Nothing 12/29: Nothing 12/30: Water 12/31: Essential Oil foliar spray (ginger, eucalyptus, peppermint, bronners soap) 1/1: Nothing 1/2: Water/Aloe

One gal hermed :( Guessing as a result of the crushed tubing a few weeks back + defoliation. However, there has been some other wonkiness this grow such as no auxiliary buds on one, and 15-point leaves on another! So perhaps this is just a weaker strain not suited for training?🤷‍♂️ Checked all the other plants and no pollen sacks just yet - fingers crossed! (I sprayed down the whole tent with water as a just-in-case measure) Last big defoliation this grow! ~~~~~~~~~~ Aside from that, everything's looking good. Smaller gals are stretching considerably, two big gals have slowed down to a crawl. The tall gals are about 12'' from lamp, the others 15" - if things don't slow down I may have to consider some HST (nooooot my preference, all things considered - I'll end up with seeds, guaranteed). Or, if I don't see any significant burn, maybe I let them go and just harvest the top portions early? We'll see! More and more hairs every day, buds are getting bigger! ~~~~~~~~~~ OK! - Its the strain! Has to be. Woke up this morning and one of the big gals had fully open pollen-sacks :(((( Picked off every one I could find with tweezers This gal did not have crushed tubing issues, and everything tracked fine. This leads me to believe that these plants just aren't meant for stress training. This day and age - the breeder will usually give you info on the subject - I can't find this online ANYwhere. I know who the breeder is - (big big name-sticker was on the bag) so this comes as quite a surprise to me...but at the same time - you can't find them on the website. Feels like it was given up on, and I snagged some of them on sale, from a distributor who had some left? Best guess. (gal starting putting out foxtails a cpl weeks later - 10'' from lamp) ~~~~~~~~~~ Thought maybe the three smaller gals could use a trellis - unfortunately I did not train them well enough - they are a little too cramped/bushy. I will have to use the Bamboo support system from here on and the trellis would clip bud-sights. So worse case, I'll use zip ties / rope to keep them supported. If its anything like my first grow - the mainline/manafold will do most the work anyhow.

Hey folks, I'm finally back at it again. It took me a while for a couple of reasons: 1) I usually only grow in the winter. 2) I completely revamped my grow room after the issues I ran into with the last setup. 3) It took me a while to brainstorm exactly what I wanted to do. I bought these seeds from D.C. Seeds and was very pleased with the experience. I'm very happy to give business to a fellow American and Veteran. I've only ever purchased seeds from the UK in the past and that experience has been "dodgy" to say the least (not the vendors fault, but the transit). I've only ever grown photo's, but chose to go with all auto's moving forward. After calculating the intensity of my current light, with it being on a 20/4 rotation I'm very close to hitting 40 moles per day, at least directly under the light. It doesn't quite cover my 2' x 5' trellis. I'll eventually upgrade my light, but auto's should get me the best bang for my buck with this light. Also, I spent a pretty penny building this new grow room. The other obvious reason for growing auto's is their shorter seed to harvest time. I've got a small grow area, and never plan on expanding. Theoretically, auto's will allow me to produce the most out of my room. A few things about my grow room: 1) I lined the whole closet with 1/2" plywood and put that piece of ply the air intake/outtake/power as the divider between each side of the closet 2) The grow room itself has ply on all wall surfaces so I could mount stuff to it and paint it 3) The other side of the closet is my storage/prep/power distribution/etc. area. Maybe I'll take a pic one of these days 4) My last grow my carbon filter/fan was venting into the other side of the closet. This created a headache for a number of reasons. I tapped a 4" hole through the floor and am now venting into my crawl space below the house. 5) I moved to bubbleponics to speed up my grows even more. I will be removing the drip system once the roots hit the water in the res. 6) The larger res. will hopefully make my life much easier. Late in the last grow I could only fit 3 gallons of water in the bucket and that sucker was pounding down at least a gallon a day. That required too much micro-managing for me (both ph and refills). 7) I no longer have a fixed trellis with chicken wire. The trellis is held in place by dowels that I can pull out by hand. The short sides of the trellis have hinges on the bottom, so I can fold it and pull it out easy-mode. Lastly, I'll be using string for the trellis so come harvest all I have to do is cut the string instead of dealing with trying not to destroy buds pulling them through chicken wire (it takes forever). 8) I built a light diffuser on the other side of the air intake 9) My res. is on a motorcycle lift I'm using a drill to move up and down I have now started using Jack's as my primary nutes. They tell you the full break-down of each macro and micro nute, giving me more control and understanding. I think House & Garden is a good product, but when stuff goes bad it's more difficult to troubleshoot when you have no idea what each piece of their full lineup contains. I'm assuming it's kind of a proprietary type thing, which I understand, but knowledge is power. I am still using their Drip Clean (while the bubbler is going) and Roots Excelurator Silver, both excellent products. I'm still using Hydroguard, and will FOREVER. I'm a true believer now of why Hydroguard is necessary for any hydro application, IMO. I also purchased water soluble fulvic acid, but have decided not to use it for this grow....or at least while the bubbler is going (I'll elaborate below). Ok...now that all that is out of the way.... I really wanted to use my well water instead of R/O to make my life easier. Soooo....I filled up my res., and put two seeds in the system immediately. Nothing happened after 1 1/2 weeks. I finally opened up the cubes and saw that the beans had popped, but it looked like maybe I drowned them, or they ddin't grow straight up or something. For round two, I didn't change the water out, and decided to soak the beans for 24 hours in R/O water first. I had the exact same problem. I'm still not really sure what happend, but I suspect it was the well water. My PPMs were sitting at ~500 with the well water, which was probably too spicy for the beans just starting. Also, my well water is questionable (even though it's at 165ppm), but I won't elaborate further....it's a long ass story and I've spent an absurd amount of money on it. Lastly, I did put the Fulvic acid in, and it was very messy. I really want to avoid having to clean my res. Once the roots get big it will be a real pain in the ass to clean. I'm leaning towards not using the Fulvic acid this grow just to see how things go. I had 10 beans total of the Sour Apple and have already ruined 4. So here's hoping third times the charm. So, I went back to my tried and true method: 0) R/O water for everything. Ditching the well water idea. 1) Soak beans in R/O water for 24 hours 2) Paper towel method between plates on a heating mat 3) Once the roots pop, I place them pointed down in the hole of the rockwool cube 4) Hand water once a day by dipping the cube in the pre-mix of 1/4 strength Jack's and everything else I've listed above. This put my PPMs at 300...a way more reasonable value for starts. It's been exactly 7 days since I followed the above. It's probably hard to see but the cotyledons came up, and multiple roots have come out the bottom of the cubes....way faster than I've ever seen since I started growing. That means even though I'm doing my old process this already shaved at least a week off of when I'd normally put it in my bucket in the past.