They continue to grow. Some of the lower leaves are yellowing. We removed these shortly after this. Soon they will go into the one Gallon pots with 66% soil mixture and 33% Happy Frog.

7/3/22 Stella is still moving along with the late bloom nutrient level this week. She’s getting close to the ripening stage, but still a week away. Today she received a full gallon of water mixed with the following nutrients: CALiMAGic - 2 ml FloraMicro - 3.8 ml FloraGro - 3.8 ml FloraBloom - 4.2 ml Floralicious Plus - 2 ml Liquid KoolBloom - 1 ml The pH was 6.6, and wasn’t adjusted. She took nearly the whole gallon before giving back some runoff, but it was sufficient. The runoff pH was 6.3. The tent was 80.5F, with a humidity of 60%. She is starting to fatten up and her branches are starting to get weighed down. I’ve already used all of my LST poles on other plants, so I’m going to have to figure out a way to make more space. She sits in the middle of the tent, surrounded by 4 of her daughters, and a smaller auto-period plant sitting on a box in front of her. My tent is FULL! I ran out of time today and didn’t get any new pics of her, so I added one that I didn’t use the other day. Take care, and happy growing everyone! If you’re in the USA 🇺🇸, July 4th💥, happy Independence Day!! 7/5/22 Well, it finally happened! Stella’s branches have gotten heavy enough to tip her over when she has space to herself. She is in the tent with several other large plants (her 4 daughters + 1), so she rests nestled amongst them, so she stands. When I took two of her daughters out of the tent to feed them, she tipped right over. To make a VERY long story short; I tied her upright with almost all of her branches bundled up loosely so that they all get light, then fastened her to the back of the tent. It’s going to make feeding her tricky, but she’ll be stable, and getting full light exposure. It also opens up more space in the tent. Not much, but some. I tied up her daughters branches too. Enough about that. She received a full gallon of water mixed with the same nutrient level as the last feeding noted above. The solution pH was 6.5, and wasn’t adjusted. She gave back plenty of runoff with a pH of 6.3. The tent was 83F, and humidity was 65%. That’s a little high to me, at least compared to my previous grows. However, my tent has never been this full before. I adjusted the fan to a higher height, and with all the plants tied up somewhat using LST methods, I’ve increased open space between them with hope of improving air flow. We’ll have to see how it goes. Happy growing everyone! 7/7/22 I’m just going to write the basics today. Stella is still triced up nicely in the back of the tent so that she doesn’t fall over because of the weight of her own branches. Her buds are continuing to fatten up, and she looks lovely! Orange hairs all through her buds! Yummy!! She’s still getting the late bloom nutrients till next week when we actually begin the ripening stage. Today she took a gallon of the following: CALiMAGic - 2 ml FloraMicro - 3.8 ml FloraGro - 3.8 ml FloraBloom - 4.2 ml Floralicious Plus - 2 ml Liquid KoolBloom - 1 ml The pH was 6.6. I thought of adjusting it, but decided that it was good enough. She gave back plenty of runoff with a pH of 6.3. The temp was 83.3F, with a humidity of 54%. I didn’t take any pictures of her today. I was running between 2 rooms, and feeding other plants and just forgot. 🤷‍♂️ I’ll get pics later. Happy growing everyone!

It's been 38 days of flower now and The gals are still loving the fc4800 and their new 8x8 mars hydro grow tent as much as I do👍 leaves are sticking straight up towards the light. They are starting to get some frost now. Quite a bit of frost too. A bud fell off because I bent it accidentally, so I just chopped it off because it was hanging and snapped. There's a picture of it below. Should be good weed with how much crystals it has and it's only 5 weeks of flower👍I Love how easy the zippers are to open and close. Nice and strong and guaranteed to last. It has extra material on the backside of the zipper that helps for light leaksand enough ports and vents for anything you need in it👍. the tsw2000 is still going strong and is also a very good light. Its been going almost nonstop for 6 months and still working the same as when I got it👍. It really got my last grow extremely frosty and is doing the same so far for this grow. I'm very happy with every product I have gotten from mars hydro 👍👍There's not much heat off both lights but the fc4800 is alot cooler and the heat-sinks work extremely well. I have it daisy chained to the tsw2000 and 1 dimmer controls the other and i don't need to be reaching in too far to dim the other light, it's awesome and I can't wait to buy more lights to daisy 4 together👍. I would recommend this light to everyone that grows with leds and have trouble with temperatures getting too high. Even if you grow with HPS lights I think any mars hydro light is a MUST TRY. I like how heavy both lights are because I know it means they are built soild and strong 💪. Very good sign with the frost they are starting to get thanks to bith mars hydro lights. I can notice more frost under the fc4800 and I'm thinking it's from the UV DIODES they put on the fc4800 👍. 2 days ago they all smelt like my nuken, sweet marshmallows. But now I can smell the monkey dough and gorilla glue and skunk monkey coming through👍. I touched a bud on the gorilla and monkey fingers smelt like fruit loops👍 really pleasant smell. Lingered on my fingers for atleast 30 min. I'm glad mars hydro is under priced compared to some brands and for how popular they are. usually companies would charge more. Thanks mars you guys are awesome 🤘🥁🎸. I'm getting a new exhaust fan soon. An 8 inch that will work alot better than my 4 inch lol. Wayyy to small for a 8x8 Grow Tent. Dehumidifier is going almost non stop to try and get the humidity down. I love how both lights on 100% power only raise my temperature 2 or 3 degrees 👍. You can rest your hand on the lights and not much heat comes off them. Obviously there is some heat but for the brightness of the lights and only raising the temp that much is awesome 👌.  And if I wanted to I could remove the driver from the fc4800 and run it on the outside of my tent because the cord is so long but 2 or 3 degrees is barely nothing👍. The girls are starting to bulk up abit now and only 3 weeks of flowering, these lights are awesome 👌.  My last run of monkey dough and gorilla glue didn't start showing alot of crystals until week 4. These were only 2.5 weeks and I started noticing some frost. Next week I will be able to tell more about what these custom bred seeds will be like. I love how the smell is changing now. Didn't want all them to smell like nuken marshmallows lol. It's awesome that I can get right inside the tent to do any work i need👍. Even if I wanted an 4x8 tent. I'd rather this 8x8 because it's so easy to work with the plants and have so much room to move around and massive headroom when I'm in there chillin with the gals🤣🤘. FOR EVERYTHING MARS HYDRO VISIT: Www.mars-hydro.com PROMO CODE: rocknroll Instagram: @marshydropenny https://youtube.com/channel/UChU5ZWwNi-DvnO3oWVU3ceA Thanks for taking the time to read and check out my shit🤜🤛 GET THE MAX FROM MARS👍: Welcome one of  the newest members of the Mars Hydro family🤜🤛🤘. The Mars Hydro FC 4800 480W LED Grow Light can accommodate up to a 4' x 4' area for flowering. It has OVER 2000 LED chips consisting of the best selling Samsung LM301B diodes which has a Luminous Efficacy of: 220 lm/W 0.2 W, 3 V mid power, Osram 660nm Diodes, Infrared light and UV LIGHT👍. It boasts the incredible efficiency of 2.8 µmol/J, maximum 2.5gram yield per watt with 30% higher Average PPFD. This High-intensity spectrum is beneficial for plants at all stages - from veg to bloom, and creates Big dense Buds👍. achieve 50% higher yields & quality compared with the old lights! Only consumes 480W for 4x4ft personal grows, and 3x3ft for commerical grow. It comes with a dimmer and daisy chain function with a  maximum of up to 15 lights, the master light controls the rest👍. Wide 6-bar design offers even & wide canopy coverage and can maximizes your grow space. slim 180° FOLDABLE DESIGN... YES I SAID FOLDABLE🤘🤣 , making it compact and easy to install, it's IP65 WATERPROOF and will give you no worries while growing in a humid environment and makes it a flexible high performance commercial grow light for enormous  SUPER FROSTY yields.😛😛😛. MARS GETS EM FROSTY BOYS👍 AWESOME HEAT DISSIPATION: The Low energy consumption FC4800 growing light has 6 passive-cooled bars and an aluminum heat-sink a removable driver  you can upgrade later or have it outside your tent. with zero noise  you can save up to 50% in your electricity bill compared to HID's or HPS lights! It also has a removable driver so you can upgrade it in the future or have it outside your grow space for better heat control in your growroom👍 UPGRADED FULL SPECTRUM: Yield Max Spectrum with enhanced red (Top-Bin Samsung 3000k-5000knm, Osram 660nm Deep Red), speed up blooming & fruiting, perfectly suited for full-cycle growing. The FC4800 LED grow lamp was born for Big Buds, perfect for commercial, grow tent, grow room, hydroponics, and all soil grows.👍 THE BEST SAMSUNG DIODES: THE FC4800 has Top Bin genuine Samsung Osram Diodes, combined with remarkable 2.8 µmol/J Efficacy, 30% higher Average PPFD, 50% less energy consumption, to maximize your yields. They give you a TRUSTED 3 years warranty 100% Satisfactory guaranteed!!! The MARS HYDRO 8x8 Grow Tent interior is made of a unique diamond design mylar which is highly reflective. (Other companies mylar and reflective rate is as low as 50%, and it won't provide efficient light. They use thick 1680D oxford canvas, and being double stitched, it is tear proof and perfect for locking in the light. Their grow tent keeps 100% of the light inside the tent and helps your plants absorb more light. EXTRA-THICK material means No light leaks or rips at all.👍 Strong Stable metal corner adapters and poles are the trustful supporters of the tent. It's very sturdy, neither rusting or paint flaking off. quick and easy tool-free setup. They use heavy-duty metal zippers, with double layer black lining, by far the best on the market which creates a light-proof seal. The Easy observation windows are made by double layers of cloth. Observe the growing conditions of your plants without opening the tent and avoid disturbing your plants. The observation windows also serves to dissipate heat and ventilate the air. The tent includes 2 removable waterproof floor trays to hold soil and water. The removable tray can be taken out to wash easily. They guarantee the grow tents are easy to install even if you've never done something like this before. Clear Instructions and no tools needed! They also offer 30-day unconditional refunds for quality problems. Just contact their friendly 24 hours customer service 👍   Track: Ethan Meixsell - Thor's Hammer [Rock] Music promoted by BreakingCopyright Watch: https://youtu.be/o6Gr0xn6U88 Download: https://www.youtube.com/audiolibrary_...

Day 28 - Full watering/feed to run-off 10%-20% at same strength as previous. (50% of maker recommended strength for coco use + cmx + root enhancer + kept extract organic additive) Day 31 - Decided lower lights by around 30cm 120cm to about 90cm. After about 8 hours the plants all suddenty wilted. They stay wilted through the night cycle as well, so I raised the lights back to where they were and they have bounced back, so I won't suddenly drop the lights by as much. If I do lower them it will be incremental. Day 32 - Bought a six fin 800w oil heater for the tent. Am going to place this under the oscillating fan and set it aiming to keep the tent around the 25-27c range. Hopefully this has the tent sorted for the rest of the grow. The humidity has been high lately due to the weather, so this might be about the only factor left to address, and I will look at getting a dehumidifier for the grow room if needed. Day 33 - Full watering to run-off 10%-20% at same strength as previous. (50% of maker recommended strength for coco use + cmx + root enhancer + kept extract organic additive) - Ordered humidity controller for extractor fan. - Ordered Temperature controller for Heater - Ordered IP Camera for remote monitoring Tent is now running fully sealed and using passive inlet and carbon filtered extraction to roof space. Plants are around 20-40cm high and the lights are 85cm above the canopy on full 480w. Day 33 - I have reduced the Light intensity from 480w to 420w. This seemed to really get a good response from the plants. I think as they've grown taller and the light intensity has quietly increased at the newly heightened canopy level the plants have been getting stressed. Day 34 - I've reduced then light intensity from 420w to 280w. I am new to the quantum boards and the concept of "too much light" so working out how much intensity, how much distance and so forth for the different stages of plants growth. I have a gut feeling 280w at 80cm might be a touch under-powered but I'll give it a full light-cycle or two to judge leaf growth and colour and make a call on whether or not to increase it or leave it as is. Day 35 - I found plants wilting during hthe night cycle without fan air circulation. So I've set the oscillating fan to run during night hours. Day 35 - I've turned up the heater a touch to bring the tent temp to around 26c. Infrared gun shows leaf temps to be around 24-25c which ideally I want to get to 27-29c - I'll aim for this metric once the other environmental factors are sorted (ventilation seems sorted so mainly just dialing in the light intensity). * I'm looking forward to setting up the heater on temperature controller, and putting the carbon filter ventilation on humidity control, and then mounting an IP camera in the tent. This should all be here in around 2 weeks. I'm looking forward to being able to view the temp/humidity and see the plants live without having to actually open the grow room. * The infrared temp gun is proving invaluable in testing leaf, coco and pot temperatures around the tent, which is giving a great view of how the heat from the heater/fan arrangement is being distributed - it shows a less than 1-2c degree variance across the tent which is just great. * Hopefully week 6 to come will be one with a lot less wilting incidents and the week that this tent achieves a somewhat final and stable environment optimised for plant growth and happiness. But so far every time I think I've got things perfected, another variable comes into play and I need to tweak something. Maybe by the end of this harvest I will have the whole process refined to a smoother less reactionary process.

~ AirCube Active Oxygen Ebb/Flow System sponsored by GrowAce, featuring Tropicana Cookies by FastBuds ~ Well guy's and gal's here we go again on another exciting Autoflower run together! This time will be different as I will be doing a 'Hydroponic' run utilizing the AirCube Active Oxygen Ebb/Flow System by GrowAce, who were kind enough to sponsor me for this run, so it should be interesting to see what results I get and have some fun along the way! •Let me first tell you about this 6 Pot Ebb/Flow system from GrowAce: "The AirCube system is the one and only Ebb & Flow grow system on the market that combines the benefits of air pruning with a fully automated Ebb+Flow system! With the AirCube's proprietary fabric pot in bucket design, this system is guaranteed to outgrow any other Ebb + Flow system on the market. The results speak for themselves- grow MASSIVE roots that result in MASSIVE fruits! Air Pruning- Air Pruning only happens with fabric pots. As the roots reach the fabric walls of the pot, they penetrate and grow into the breathable fabric. Once penetrated, the roots are exposed to air, which causes the tips of the root to dehydrate and naturally prune themselves. This natural pruning process forces the roots to grow tons of lateral fibrous feeder roots. This results in a plant that utilizes the entire root zone and fills the entire pot with tons of roots. These fibrous feeder roots are incredibly effective in uptaking water and nutrients, resulting in a plant that grows healthier and more vigorously! Oxygen Benefits- Without oxygen, nutrient absorption cannot occur. On a molecular level, oxygen is needed to transmit nutrients across the cell walls and into the roots of a plant. With the AirCube's proprietary bottom lifted draining design, the system actively draws all of the water out of the bucket pulls vital oxygen into the root zone. Maximum Versatility with Any Grow Medium: The AirCube System is the only system on the market that allows you to use any growing medium you like. Use coco coir, soil, peat moss, perlite, vermiculite, hydroton, rockwool or any other medium you wish! This system is the most versatile Ebb and Flow bucket system in today's hydroponics industry. Temperature Control- with the fabric pots constructed with highly porous polypropylene fabric, heat dissipates easily and effectively. Unlike standard plastic pots, heat isn't trapped in the root zone. Heat in standard plastic containers can reach temperatures of up to 125 degrees. When this type of heat is trapped and unable to escape, it can damage your plant's health and limit the potential of your harvest. Growing in the AirCube System, plant roots grow cooler, healthier, and more vigorous. Largest Pots in its Class- this system features 5 Gallon grow buckets, the largest pot size of any other ebb and flow hydroponic system in the market. Modular and Expandable- start with 6 grow buckets and expand up to 36 grow buckets with the optional 105 gallons PopTank reservoir!" For my medium and nutrients I decided to also switch things up from my regular Organic runs, going with Plagron Nutrients and Root Royale 70/30 Coco/Perlite. When filling the fabric pots with medium, I first added just under a gallon of horticulture perlite from Nor-Cal as a base layer to ensure good drainage and then filled the remainder with the Root Royale. •Now for the outstanding, award winning strain from my friends at FastBuds... Tropicana Cookies Auto: I'll be running Tropicana Cookies Autoflower which is a 60/40 Indica/Sativa Hybrid. "Tropicana Cookies Auto is the perfect variety for growers of all levels, especially beginners as this strain performs very well outdoors and indoors, and can produce up to 500 gr/m2 in 56-63 days without needing extra maintenance. Reaching up to 110 cm, this strain grows fairly tall with medium-sized branching, showing its mixed heritage. Definitely the right choice for those with a high tolerance looking to get their hands on the strongest autoflowers out there. You can expect an extremely powerful and long-lasting high that’ll boost your mood and give you that extra push you need to start your days on the right foot. This variety offers the whole range of citrus and woody flavors with a strong candy-sweet background that will keep you coming back for more and more."* *References: GrowAce.com, 2fast4buds.com ______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ The Setup: • AC Infinity 4x4 tent •AC Infinity Cloudline T6 Exhaust Fan w/ Controller 67 •HLG 650R w/UVA Bar *** For some reason GD does NOT have a listing for the USA version of the 650R so I selected the closest match to it. •AirCube Active Oxygen Ebb/Flow 6 pot System •DL Wholesale Root Royale Coco Lite 70/30 coco/perlite •TrolMaster Hydro-X Controller for light •AutoPilot APC8200 co2 controller fed by a 50# tank •16" Hurricane oscillating fan and 8" floor fan •Tent cooling via filtered outside air delivered by AC Infinity Cloudline T6 fan •BlueLab instruments: PH Pen and Truncheon Nutrient Meter ______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ Weekly Updates: 10/29- Here we go into the fifth week from seed for the FastBuds Tropicana Cookies and the #2 and #3 are just starting to flower! The #1 is just starting to show signs of pre-flower, so she'll not be very far behind the other two. Today I adjusted the feeding schedule for the Tropicana Cookies to six feeds a day. The first feed begins two hours after 'lights on', then every three hours until 'lights off' which the girls should enjoy! I am currently keeping the nutrient level to 800ppm, and have begun to introduce Plagron's Green Sensation @ 2ml/g. I'm curious as to how much, if any, stretch these girls will have... I guess time will tell. 10/31- 👻HAPPY HALLOWEED! 🎃 11/2- The Tropicana Cookies are all looking really good now. The #2 and #3 are beginning to flower, the #1 should be showing any day now. The #2 is still a bit paler than the others, but I have noticed a steady improvement in her color. I have also used some horticulture wire to do some LST on #2 and #3 to spread out their numerous side branches exposing them to more light. Our weather has finally cooled off now allowing me to keep better control over the tent temperatures. I now have the HLG 650R turned up to 100%, and hung 28" above canopy. The Tropicana Cookies remain on six 15min feeds a day, and I have adjusted the nutrient level to 900ppm @ 74℉, while maintaining a ph range of 5.9-6.4. 11/4- Well there's five weeks of growth, and one week of flower for the FastBuds Tropicana Cookies! They are really digging the GrowAce AirCube system, and I must say so am I! I'm getting used to the routine now of checking the reservoir, cleaning/refilling, and maintaining the environmental s which is showing in the condition of the plants. Hopefully, things will continue on this track and the end results will be epic! See you next week fam!😎🙏💚💚💚 💚 Thank you for checking out my passion in life! Please visit as often as you wish and I hope you enjoy this journey as much as I know I will! Grow what you love, Love what you grow!💚

12/30/23 - Day 54 - Hello All! I started this week a day early. I wanted to update everyone on something I have been thinking about a lot. Curing. I feel if there was a hole in my growing skills it would be curing. Last grow there was more than I had anticipated. I was not set up for curing 1 lb. I threw in an audible at the last minute. It worked out but I know I can improve with some trial and error and hands-on experience. So after reading a ton, and going off of some of my prior builds for drying, I came up with this design. I have a controller that will turn the air on and will run when the contents inside the box hit whatever RH% I want to set it at. I think the first week I will set it for 78%RH, then every couple of days go down a % until I hit 62%. The thought is that if the bucket gets above the set RH% then the air will kick on and distribute air across the buds until the RH% is back down to where you want it. It will force the humidity out. I won't need to worry about burping. It will happen on its own.... in theory. Ill update tomorrow with some pictures after the water change. 12/31/23 - Day 55 - Everything is looking good. The water change completed this morning while I was in the shower. Its adding nutes now and will do so over the next hour or so. She is starting to get stinky. I had to add the extra carbon filter to the room. I've got some pics up top of that. Happy New Year! Next time I post it will be in 2024! Have a great night and be safe! Dont drink and drive, your life and anyone else involved in an accident is too important! C' YA! 1/4/24 - Day 58 - I have been thinking of trimming her for a while.... I got a comment on the bushy-ness and I got self-conscious and gave her a trim. Lol I have been going bath and forth for a while and that gave me the push to give her a little trim. She looks great and is growing really quickly. Ill update with more pics as it goes along.

Hello folks, been a progressive week. Girls are stretching quiet bit especially the Sativa dominant Stardawgs on the trellis net side. The other side has Blue dream and stardawg. Both look indica dominant as they are squat and bushier than the above 2. Trellis netting for that side should be up by next week. It came in post today so.... Recharge is started in the feed and girls are looking very healthy, I like the smell of it so the girls must too 😇 they get flush once per week. When the things actually start , Will be flushing them twice a week, so technically on every feed. Works out the best ALWAYS !! They are lolipopped and I will be removing any bud sites if they grow back to focus supply to upper part. Week or so more and this should look like a bed of buds 😎 Stay safe, cyall nxt week.

Friends, we're almost at the end, there's still a week or so left to harvest.

Día 101 (09/09) Riego con 500 / 1000 ml H2O pH 6,5 Parece que se ha parado un poco el amarilleamiento que subía tan rápidamente por las plantas! Día 102 (10/09) Riego con 500 / 1000 ml H2O pH 6,5 Excepto LemonPaya, todas las plantas empiezan a llenarse de tricomas! 😍 Día 103 (11/09) Riego con 500 / 1000 ml H2O pH 6,5 Estoy emparanoiado con que la floración va lenta... Día 104 (12/09) Los cogollos no se están formado correctamente... Algo pasa... Los pistilos tienen un extraño color verde y no engordan... OnionOG #1 es la única que tiene un ritmo normal... Riego con 250 / 500 ml porque las temperaturas empiezan a bajar a 25 ºC diurnos / 22 ºC nocturnos y está bajando el consumo de agua... Día 105 (13/09) La deficiencia empeora... Solo se salvan OnionOG #1 y KS1 #2... Día 106 (14/09) La deficiencia sigue empeorando... Solo se salvan OnionOG #1 y KS1 #2... Día 107 (15/09) La floración se ha ido al traste! (Excepto OnionOG #1 y KS1 #2) Tras preguntar a Lurpe, GD e IG concluyo que el super soil tiene un bloqueo de nutrientes Debido al bloqueo, se ha detenido la floración en 4 de las 6 plantas Siguiendo las recomendaciones de Lurpe, hago flush hasta que el agua de escorrentía tiene una EC 2,5 (1250 PPMs) A ver si les da tiempo a recuperarse... 💦Nutrients by Lurpe Solutions - www.lurpenaturalsolutions.com 🌱Substrate PRO-MIX HP BACILLUS + MYCORRHIZAE - www.pthorticulture.com/en/products/pro-mix-hp-biostimulant-plus-mycorrhizae

Gracias al equipo de AnesiaSeeds, Marshydro y XpertNutrients sin ellos esto no sería posible 💐 🍁Pink Matcha Slush: es un híbrido con una ligera dominancia índica (60% índica) que ofrece altos niveles de potencia y un aroma increíblemente delicioso. La cepa tiene el subidón perfecto de efectos índica y sativa, y trae consigo una gran potencia que puede dejarte completamente anonadado si no tienes cuidado con la dosis. El subidón es rápido y potente, con una euforia cerebral vertiginosa. Te sientes concentrado, sociable y lleno de energía. Es una planta de crecimiento veloz cuando empieza a florecer, llegando a alcanzar una altura de 100-120cm en interior, las plantas pueden alcanzar hasta 2m de altura en exterior, proporcionando una gran cantidad de rendimiento Los efectos energizantes y el increíblemente alto contenido medio de THC del 31% hacen de Pink Matcha Slush una valiosa variedad terapéutica para su uso contra el estrés crónico, los cambios de humor, la depresión, la fatiga crónica y el TDA/TDAH. 🌻 🚀 Consigue aquí tus semillas: https://anesiaseeds.com/es/product/pink-matcha-slush/ 💡 Mars Hydro TS 3000, como la lámpara de cultivo LED más grande de la serie TS, ofrece suficiente cobertura para un área de 4 × 4 pies con un precio asequible y rendimientos de calidad; a cambio, se puede aplicar tanto al cultivo doméstico como al cultivo comercial. Potencia - 450w Cobertura Vegetal – 5×5 pies Cobertura de flores - 4 × 4 pies La opción abrumadora para la mayoría de los productores que la aplican en tiendas de campaña. Consigue aqui tu lámpara: https://marshydro.eu/products/mars-hydro-ts-3000-led-grow-light/ 📆 Semana 11: Esta siendo una floración un poco mas larga de lo esperado por factores ambientales y por una mudanza inesperada, por lo demás todo bien, planta sin ninguna flor macho ♂️, cargada de resina y sin exceso de nutrientes, a partir de ahora agua has el final.

Venga familia que ya viene la cosecha de estas Apple Fritter de ZamnesiaSeeds, que ganas que tenia ya de darles machetazo. No veas que pinta que tienen estas plantas. Las flores aparte de prietas se ven bien resinosas. a sido una genética con la que disfruté mucho cultivarla, es algo complicada cultivarla pero merece la pena si eres cultivador con experiencia no te será problema cosechar. Agrobeta: https://www.agrobeta.com/agrobetatiendaonline/36-abonos-canamo Mars hydro: Code discount: EL420 https://www.mars-hydro.com/ Hasta aquí es todo , espero que lo disfrutéis, buenos humos 💨💨.

First feeding of week 3 juste before taking pictures!! 😁🍀✌️ Day 17 one of the gorilla melon looking not really happy after feeding!! She was doing great I don’t really know yet if it’s a deficiency or over feeding but I’ keep an eye on it 💚✌️ Day 18 I accidentally dropped a full bottle of water on my gorilla melon, which split in two at the base and break the pot😭she wasn’t able to stand alone so I hold her luck she continue to grow 🍀💚✌️

Belle couleur gorilla sherbet#1 sens très fort.

Kicking off week 5. Did some extra work on the LST. Making sure the light penetrates all bud sites. I now understand that my initial goals are too far from what I actually will harvest..mainly due the PH issue we faced on week 4. Let's see how it goes.

esta semana todo bien. los cogollos siguen engordando . algun signo de problemas de calmag ahi, pero nada grave, es algo relativamente normal al cultivar en coco. he recortado algunas ramas para dejar mayor paso de luz a algunas porras.

MIMOSA by ROYAL QUEEN SEEDS Week #20 Overall Week #3 Flower This week she's doing good just starting to flower so that's always exciting to see no issues this week she's healthy!! Stay Growing!! Royal Queen Seeds MIMOSA