This week I defoliated slightly for better air circulation and improved light penetration, mainly removing leaves blocking budsites that had purple petioles. They seemed to respond good. Also foliar sprayed with light potash solution, upped pk with guano and provided micros with seaweed extract. Feed EOD and water with silica in between feeds. RH now around 50-50% most of time. Improving air circulation is now top priority on to-do list

week 1 flower is going well.

Day 36/Flower Day 8 - Starting to get them girle bits showing now. Stretch is still unreal but the smaller nodes that have crept up to the top are thickening their branches so that’s a good sign they'll hold something and if not, have a spare elasticated SCROG net for support, which will DEFINATELY be needed by the looks of things!!! The main branches are sitting near as thick as 1 of the stems of my last grow so these girls are definitely sturdy and strong growers! If only they didn't push for the roof!!! Apart from the one SCP (#2) that is staying squat in the back corner...sub nodes getting up there but the "tops" staying low and bushy!!! When I start to see a few more flower sets/bud buttons proper actually forming, I'll start inching up the lights to 13/11 over the week...still tempted to start it now but thinking best to wait til the bloom nutes get upped drastically (which is next week - will be upping them by about 50-60% volume). Feared a bit right now that the extra light may fuel some stretch rather than fuel the flowers...but then again, having the plants acclimatise to 13/11 by the time the buttons are forming may not be bad...but then again, that 13/11 may slow down their formation!!! Choices and Choices!!! Was expecting the flower initiator would have knocked some time of the pre-flowers showing (can't think now if nodes were asymmetrical before flip...honestly couldnt have vegged any more though...or could I???) but nope, hopefully the buttons start to set quickly now though. Apart from that, all going well so far. Been a bit of a drop in the temps outside and clearer nights so hopefully that helps bring day temps and night temps down a bit - bringing down humidity some too. Need to restart my CO2 Jug now for the flowers and keep on watching them grow! Happy growing all! 💪

Flowering in full effect...still no need for watering because of rain...found some molasses so it a sweet treat today.

Got two down today, probably pull the last tomorrow

[Week 1 - Germination] The Fat Banana seed has germinated and looks very healthy. Very small leaves have appeared in the past two days!

Day 71. Girls just perfect ;))) As any grower i would want, bigger, fatter, stronger, but they are in that range anyway, now main thing not to screw up ;))) Girls on nute, water, water+calmag, water+silicaAcid, water+molasses rhythm and just love life ! Day 72. Got more presents, thank You Zamnesia ! Asked for 4 strains, got 2 ;))) Still 10 beans and full grow by one house, like i always try to do. Always wanted to try out Runtz, all grows that i saw - was sick ! Kalini Asia - new taste and strain for me 4sure ! Day 76. All is good , they are missing CalMag from those lights a bit and with such amount of buds, but should be fine. Todays watering was only with CalMag, ph 6.5. Next watering full nute blast, should be fun to observe, they are starving a bit , so i hope for huge grow rate after. Tried 4 month cured weed at a friends, he had to chop girl on week 6 of flower, with nutes still being fed. After an hour head pain , ash was still black ... I would never try not to flush .... Happy growing !

Got a dehumidifier it’s reading different from what mine controller 69 is saying but I have it set at 40% it’s the lowest so it’s going pull humidity regardless right now it’s about 53% which is okay would like it to get down to the 40’s I also changed the light schedule today to 20/4 the humidity raises at in my tent when lights are out so I figured change it to 20/4 instead of the 18/6 I’ve been running so if humidity does go over it won’t be for as long as before hopefully this works just trying to avoid any mold situation So far the Amneisa Haze 2 is at stretching she’s going be big I can but the haze 2 is done seems to just be flowering the sour diesel is looking good as well so far I’m happy with its looking like left town for two days and the auto watering pots worked!

Humbold Sour Diesel High mellow, keeps you focsed, relaxed and calm. Terps, sweet citrus with a greasy warmth. Not a big fan Buds, only top buds swoll, the rest only popcorn buds

Week 21 (4-11 to 10-11) 4-11 Temps: 18.1 to 23.2 degrees Humidity: 50% to 64% 5-11 Temps: 17.3 to 25.4 degrees Humidity: 45% to 61% Watering: Both 700 ml. Strength of the light set from 75% to 80% Dry Weight #1: 3.5 kg. #2: 3.4 kg. 6-11 Temps: 17.4 to 25 degrees Humidity: 49% to 67% Watering: Both 700 ml. Dry Weight #1: 3.7 kg. #2: 3.6 kg. 7-11 Temps: 17.9 to 24.1 degrees Humidity: 49% to 67% 8-11 Temps: 17.4 to 25 degrees Humidity: 49% to 69% Watering: Both 700 ml. Dry Weight #1: 3.8 kg. #2: 3.7 kg. 9-11 Temps: 18 to 25.5 degrees Humidity: 47% to 64% Dry Weight: Both 3.9 kg. 10-11 Temps: 18 to 26.1 degrees Humidity: 47% to 64%

~ AirCube Active Oxygen Ebb/Flow System sponsored by GrowAce, featuring Strawberry Gorilla Auto by FastBuds ~ Well guy's and gal's here we go again on another exciting Autoflower run together! This time will be different as I will be doing a 'Hydroponic' run utilizing the AirCube Active Oxygen Ebb/Flow System by GrowAce, who were kind enough to sponsor me for this run, so it should be interesting to see what results I get and have some fun along the way! •Let me first tell you about this 6 Pot Ebb/Flow system from GrowAce: "The AirCube system is the one and only Ebb & Flow grow system on the market that combines the benefits of air pruning with a fully automated Ebb+Flow system! With the AirCube's proprietary fabric pot in bucket design, this system is guaranteed to outgrow any other Ebb + Flow system on the market. The results speak for themselves- grow MASSIVE roots that result in MASSIVE fruits! Air Pruning- Air Pruning only happens with fabric pots. As the roots reach the fabric walls of the pot, they penetrate and grow into the breathable fabric. Once penetrated, the roots are exposed to air, which causes the tips of the root to dehydrate and naturally prune themselves. This natural pruning process forces the roots to grow tons of lateral fibrous feeder roots. This results in a plant that utilizes the entire root zone and fills the entire pot with tons of roots. These fibrous feeder roots are incredibly effective in uptaking water and nutrients, resulting in a plant that grows healthier and more vigorously! Oxygen Benefits- Without oxygen, nutrient absorption cannot occur. On a molecular level, oxygen is needed to transmit nutrients across the cell walls and into the roots of a plant. With the AirCube's proprietary bottom lifted draining design, the system actively draws all of the water out of the bucket pulls vital oxygen into the root zone. Maximum Versatility with Any Grow Medium: The AirCube System is the only system on the market that allows you to use any growing medium you like. Use coco coir, soil, peat moss, perlite, vermiculite, hydroton, rockwool or any other medium you wish! This system is the most versatile Ebb and Flow bucket system in today's hydroponics industry. Temperature Control- with the fabric pots constructed with highly porous polypropylene fabric, heat dissipates easily and effectively. Unlike standard plastic pots, heat isn't trapped in the root zone. Heat in standard plastic containers can reach temperatures of up to 125 degrees. When this type of heat is trapped and unable to escape, it can damage your plant's health and limit the potential of your harvest. Growing in the AirCube System, plant roots grow cooler, healthier, and more vigorous. Largest Pots in its Class- this system features 5 Gallon grow buckets, the largest pot size of any other ebb and flow hydroponic system in the market. Modular and Expandable- start with 6 grow buckets and expand up to 36 grow buckets with the optional 105 gallons PopTank reservoir!" For my medium and nutrients I decided to also switch things up from my regular Organic runs, going with Plagron Nutrients and Root Royale 70/30 Coco/Perlite. When filling the fabric pots with medium, I first added just under a gallon of horticulture perlite from Nor-Cal as a base layer to ensure good drainage and then filled the remainder with the Root Royale. •Now for one of my favorites, and award winning strain from my friends at FastBuds... Strawberry Gorilla Auto: I'll be running Strawberry Gorilla Autoflower which is a 55/45 Sativa/Indica Hybrid. "ATTENTION ALL! Due to our continuous efforts in evolving our breeding process, we are proud to confirm that our Strawberry Gorilla Auto has now become one of the most potent autoflowers in the world! Paving the way to our recent success where she ranked on top & brought home the gold at the very first American Autoflower Cup in California. Moreover, she proved that not only modern autoflowers can compete with photoperiods, but they can even beat them in their field. At the most recent edition of the Farmer’s Cup and competing against various photoperiodic strains, Strawberry Gorilla Auto took home the title of 'Highest Combined Terpenes' in the highly sought-after 'Home Grow Hash' category, with an impressive 97.163 mg/g total terpene content! Our exceptional genetic selection's crowning Strawberry Gorilla Auto strain is a spectacular hybrid known for producing yields of up to 600 gr/m2 in 70 days. This is a very manageable grow that can reach heights of up to 150 cm - due to its magnitude we recommend it for more experienced growers, as a huge plant may be a little overwhelming for first-timers. This show stopping sativa heavy hybrid is perfect as an all day smoke, producing a taste bud tingling, pungent berry and diesel terpene-rich flavor combo that leaves you with a grin from ear to ear, a perfect choice for those looking for a day-and-night autoflower! "* *References: GrowAce.com, 2fast4buds.com ______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ The Setup: • AC Infinity 4x4 tent •AC Infinity Cloudline T6 Exhaust Fan w/ Controller 67 •HLG 650R w/UVA Bar *** For some reason GD does NOT have a listing for the USA version of the 650R so I selected the closest match to it. •AirCube Active Oxygen Ebb/Flow 6 pot System •TrolMaster Hydro-X Controller for light •AutoPilot APC8200 co2 controller fed by a 50# tank •16" Hurricane oscillating fan and 8" floor fan •Tent cooling via filtered outside air delivered by AC Infinity Cloudline T6 fan •BlueLab instruments: PH Pen and Truncheon Nutrient Meter ______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ Weekly Updates: 10/25- Here we go into the third week from breaking ground for the FastBuds Strawberry Gorilla's and they are all looking healthy! I am continuing the feedings of Plagron nutrients three times daily, and I'm monitoring the reservoir before each, adjusting the nutrient level to 650-700ppm @ 5.9-6.2 ph. The solution temperature is maintaining a steady 73-75℉. As a side note; as the weather gets colder I may install a heat mat, controlled by a thermostat, under the reservoir to ensure proper temp's in it. 10/27- Our weather has warmed up the past couple of days. Because of this I've had to lower the light output to 55% in order to keep the tent temp's below 82℉. The Strawberry Gorilla's are showing zero sign of heat stress so I'm not terribly concerned, especially as the weather will be dramatically cooling off in a day or two. I upped the nutrient ppm level to 800 with the addition of Plagron's Royal Rush 8-0-0 which will continue in their feeding through flower. I'll also be adding Plagron Green Sensation in another 7-10 days which will also continue through flowering. I'm continuing to tuck shade leaves daily on all three girls, and have been gently bending down their side branches as well. 10/29- Today I adjusted the feeding schedule for the Strawberry Gorilla's to six feeds a day. The first feed begins two hours after 'lights on', then every three hours until 'lights off' which the girls should enjoy! I am currently keeping the nutrient level to 800ppm, and have begun to introduce Plagron's Green Sensation @ 2ml/g 10/31- 👻 HAPPY HALLOWEED! 🎃 💚 Thank you for checking out my passion in life! Please visit as often as you wish and I hope you enjoy this journey as much as I know I will! Grow what you love, Love what you grow!💚

Boy I wish I had gotten a better start in the begining with this lady she has hard as rock nuggets .The pot was too small and the thing cracked from the roots massing up together .. The cooler temps in the end hurt her a lot now I'm thinking she will get the chop soon I'm starting the flush on this lady today and can't wait to see her buds drying ... She won't be a big yielding girl...

Start of week 6 The hedgehog on the 2 sins are insane and now it's time to pump ul the volume everything going great and the smell is very unique visit www.marshydro.eu for your best gear and use the PROMO CODE: DEVILSBUD Some info about the Marshydro FC-4800 Superb Quality LED Chips: The whole light is composed of 1206 pcs Samsung lm301b and Osram 660nm chips. More than two times as many LEDs are used to drive the grow lights at low currents and to avoid overdrive. Quality is guaranteed and efficiency is up to 2.8 μmol/j. Even PAR Distribution and High PPFD Output: The multi-light bar design and the densely distributed light chips enable the LED grow lights to achieve the optimum PPFD required for plant growth over the entire effective coverage area. Specifically Designed Spectrum: To ensure even plant growth, blue and red light are enhanced on the basis of a full spectrum combination. Not only does this accelerate plant growth, but it also improves the yield and quality of the plants at the same time. Dimming Daisy Chain Function: The dimming function saves on electricity costs and enables brightness from 10% to 100% for the different stages of plant growth. A single master light can connect up to 30 lights in a daisy-chain system. Business LED Grow Light: The light's wavy heat sink dissipates heat quickly and the IP65 waterproof allows the light to operate in humid conditions. 180° collapsible feature for easier installation. All these features provide favorable assistance for commercial cultivation. And some tent info ●【Lock All Light Insid】MARS HYDRO Grow Tent Interior is made of diamond mylar. Non-toxic to the environment, no harm to plants. High-quality 1680D canvas being double stitched, (ALL OTHERS BRAND grow tent is 601D canvas) which is tear-proof for perfect light locking, No light leaks or rips at all. ●【Durability Grow Tent】Stable Metal corner adapters and poles are the trustful supporters of the tent. No rusting nor paint-falling. Quick easy tool-free installation. Carries strong heavy-duty SBS zippers, double layer lining to create a light-proof seal. ●【Easy Observation of your Plants】Special peeks window made by double layers of cloths. Observe the growing conditions of your plants without opening the tent and avoid disturbing plants. The peek window also serves to dissipate heat and ventilate air. ●【Removable Tray Keep Clean】The package includes a removable waterproof floor tray to hold soil and fallen leaves. The tray can be taken out easily to wash. Removable and water-proof makes cleaning easy. ●【Good Ventilation&Fast Assembly】 Circular double-sleeved vent holes with adjustable nylon strap for air circulation by exhaust fan, ducting, carbon filter, or reflector. Better allows proper light, heat, and airflow. Quick tool-free installation. Reinforced by a sturdy metal frame to ensure security and stability, supports up to 140lb. Perfectly safeguard your plants to thrive even in winter

Well looks like we are going to have another beautiful sugar cane come harvest time of everything continues to go smooth. I just love everything about this strain. It's a potent frosty beast. Shes starting to pop like they always do. I spread the plants out a little this week so they get better light and air flow. Other than that I haven't done anything besides keep the reservoir full. Still pumping nutrients 1 minute on 20 minutes off. They are getting .5 tsp maxibloom per gallon. Not going to run any boosters this round. They dont look like they want or need it.

Heyoka. 12x12=144, A dodecahedron is a polyhedron with 12 faces, and in coordination chemistry, it refers to a geometry where ligands surround a central metal atom (in this case, Magnesium) in a specific, 8-coordinate arrangement. Dodecahedrane is a hydrocarbon, meaning it's composed solely of carbon and hydrogen atoms. The carbon atoms are arranged at the corners of a dodecahedron, a 3D shape with 12 pentagonal faces. The water molecules in the dodecahedron form hydrogen bonds that are individually slightly weaker than in either the dimer or the tetramer. However, because three-quarters of the O -H groups in the dodecahedron form hydrogen bonds, it has a more negative energy per molecule than has either the dimer or the tetramer. Magnesium (Mg2+) is the essential, central metal ion in the chlorophyll molecule, crucial for photosynthesis by enabling light absorption and energy transfer. It is chelated by four nitrogen atoms within the porphyrin (or chlorin) ring structure. Chlorophyll appears green because it reflects light in the green region of the visible spectrum, specifically between 490 and 570 nm. The main resonance electronic frequency of a neutral Magnesium (Mg) atom corresponds to the transition from the ground state to the first excited state. Resonance Line Wavelength of Mg2+: 285.1nm (UVB light). The central atom of the chlorophyll molecule is Magnesium (Mg2+), which is coordinated within a porphyrin ring. The electronic "resonance frequency" of this central atom—meaning the frequency at which its electrons absorb energy—is primarily driven by the electronic transitions (ETR) of the surrounding conjugated chlorin ring structure, rather than a discrete atomic transition of the Magnesium atom itself. The resonant electronic frequencies of the chlorophyll porphyrin (technically, a chlorin) ring are determined by the energy required to promote π-electrons within its conjugated system, primarily appearing in the blue and red regions of the visible spectrum. In standard physics, Chloryphyll b has peak absorption at 460nm (Blue). If we take the peak wavelength 460nm and a UV-B, UVR8 peak absorption wavelength 285nm Tryptophan-285 (W285) Sensing protein. 460/285=1.618 Φ, "natural harmony" and the "structure of light". The cryptochrome photoreceptor (CRY) is a UV-A/blue light receptor that shares this dual sensitivity with several other biological structures and functions, including significant sequence similarity and a common evolutionary ancestor with DNA photolyase enzymes. These are light-activated enzymes that use blue/UV-A light to repair DNA damage caused by UV-B radiation in plants. Dodecahedrane (C20H20) is a hydrocarbon with a cage-like structure where carbon atoms form 12 pentagonal faces (a regular dodecahedron). It is highly symmetric (icosahedral), contains no delocalized electrons (no aromaticity), and has minimal angle strain, but significant torsional strain. Water Dodecahedron (H2O) forms hydrogen-bonded cages. While individual hydrogen bonds in this structure are weaker than in the linear dimer or tetramer, it has a more negative total energy per molecule. This is because three-quarters (75%) of the groups are involved in hydrogen bonding, creating a very stable, closed-shell configuration. a 3D carbon hydrocarbon (C20H20) to stable water clusters in hydrate, while the Magnesium ion acts as the central activator within a conjugated ring in biological systems, with its electronic absorption dominated by the ring, not the atom itself. Effective quantum efficiency of photosystem II, often denoted as ΦPSII In horticultural lighting, adding 730 nm (far-red) LEDs alongside standard red/blue lights has been shown to increase canopy photosynthesis by 20–30% in several crops by acting synergistically with shorter wavelengths. However, the limitation is that excessive, pure IR/Far-red light (without accompanying red light) can trigger the "shade avoidance response," causing plants to grow tall, weak, and spindly rather than robust. Knowing is half the battle however, engineering or utilizing infrared light (specifically the 700-750 nm far-red range) is a viable method to boost photosynthetic efficiency. It acts as a bridge to allow PSII to utilize a broader spectrum of light, breaking the traditional 700 nm barrier. Extend, then multiply. UVR8-mediated signaling (often in conjunction with CRY proteins) triggers protective mechanisms that maintain the stability of the photosynthetic apparatus (including LHCII and reaction center proteins), thus ensuring that the efficiency of Photosystem II remains higher in UV-B-exposed plants compared to plants lacking this receptor. ΦPSII indictates the rate of electron transfer from water to plastoquinone, which drives the production of ATP and NADPH. There is a close link between ΦPSII and the true rate of CO2 fixation (Φ*co2), particularly in C4 plants. Effective quantum efficiency of photosystem II, often denoted as ΦPSII, represents the proportion of light absorbed by Photosystem II (ΦPSII) that is actually used in photosynthetic electron transport. It is a key indicator of how efficiently a plant is using light for photosynthesis, as opposed to losing it as heat or fluorescence. ΦPSII (effective quantum yield of photosystem II) functions primarily as a "multiplier" (a coefficient of efficiency) rather than an additive factor when estimating the overall photosynthetic electron transport rate (ETR). Multipliers are considered far more beneficial than additions because they generate exponential growth, leverage existing resources to their full potential, and create sustainable, self-multiplying capacity, rather than just incremental, linear increases. Humans, and most other mammals, rely on other mechanisms, such as nucleotide excision repair, to manage and repair UV-induced DNA damage. As such, humans do not have the direct, light-driven repair mechanism that photolyase offers in plants.

Left N1 to grow for 2 more weeks with cotton berry plants as they need around 2 more weeks as well. All other plants are big with loads of buds. This seed line is super good

Watering has jumped up to every 2 days ph 6.3-6.8 with 20% runoff Flower Fuel has been added to AP,GG and ZK watering's. Lights have been lowered to 24-28 inches. White Widow just started flower at end of the week. Still waiting on the Cream Cookie. Doing light Defoliation to expose bud sites to the lights.