Recommended
Processing
Likes
Comments
Share
@
Follow
Likes
9
Share
@TPBzh
Follow
Big week, lot of bending, and not Always easy, some breakings...but quite a nice shape at the end. I defoliate a bit, and give them a 4h night now. Everything look nice, they are flowering and look healthy and very fast!
Likes
9
Share
@NanoLeaf
Follow
End of Week 6 Added CO2 with regulator and controller! Added the trellis net to spread out the canopy and get more even light to bud sites. The ladies have lost some momentum and they're drinking less because of the pest issue. Although they should be growing faster because of the CO2 supplementation I'm sure when the thrips are gone they will explode. I also performed some HST by removing fan leaves and softly pinching and bending some of the stems to open up the canopy whilst keeping the stress at a minimal. Pest Report: Still fighting the thrips... Every time I spray Bio-Insek and Xterminator (Agro-Organics) it deals with the problem for a few days until the eggs and larvae that the thrips left behind hatch and start munching on the plants again. The ladies are strong and healthy and get a slight wilt when I haven't sprayed IPM for a few days this tells me that its not a major issue but I need to get rid of them especially because I want to flip to flower soon. It seems that the problem is under control. Now I will apply it weekly to make sure those buggers are ELIMINATED.
Likes
22
Share
@Rangaku
Follow
Good growth on the wedding glue , not quite ready to be tied down but she’s next on the list prolly at the end of the week . She was transplanted again into her forever home looking to double her size again the coming week . Life’s good .
Likes
11
Share
Week 16 - Day 103 08/16: Harvested Aaliyah on 08/15, Day 102 from soil and Day of flowering. After one week of pure water for Aaliyah, some of the trichomes have turned amber. I decided to harvest about 3/4 of the plant. Some of the lower buds didn’t receive enough light during the grow, so I’m hoping they can grow a little more before I bring the whole plant down. I also removed some of the dead and very young growth that was coming up. I didn’t have another spot to hang the buds because of the smell, so I tied them over the other plants. Now that she is mostly harvested, the smell has increased. I now have Annie on the side so she is getting less direct light. She already took some bleaching on her main colas. Alexis still has about a week left. I’ll check her trichomes before the next watering to see if I should start flushing. 08/18: Aaliyah’s harvested buds were getting close to being dry, so I decided to start cleaning up some of the sugar leaves. The smaller, less developed buds got chopped up and set aside for some dry ice hash. Since she was on the left side of the tent, a lot of her colas did not receive enough direct light. I hung up a few of the nicer looking ones that I’m keeping as flower to finish drying. [General notes: I still don’t have a scale to take note of the exact wet weight, but I’ll make sure to have one for the dry weight. And since all three plants are of the same strain, I’m going to wait till the last one is chopped up before posting the full harvesting results.]
Likes
11
Share
Una semana mas de vegetación para dar el inicio de la floración, realizamos ciertas podas en las ramas bajas. Se ve un bonito color, además de que se ven plantas sanas y enérgicas!
Likes
54
Share
~ AirCube Active Oxygen Ebb/Flow System sponsored by GrowAce, featuring Strawberry Gorilla Auto by FastBuds ~ Well guy's and gal's here we go again on another exciting Autoflower run together! This time will be different as I will be doing a 'Hydroponic' run utilizing the AirCube Active Oxygen Ebb/Flow System by GrowAce, who were kind enough to sponsor me for this run, so it should be interesting to see what results I get and have some fun along the way! •Let me first tell you about this 6 Pot Ebb/Flow system from GrowAce: "The AirCube system is the one and only Ebb & Flow grow system on the market that combines the benefits of air pruning with a fully automated Ebb+Flow system! With the AirCube's proprietary fabric pot in bucket design, this system is guaranteed to outgrow any other Ebb + Flow system on the market. The results speak for themselves- grow MASSIVE roots that result in MASSIVE fruits! Air Pruning- Air Pruning only happens with fabric pots. As the roots reach the fabric walls of the pot, they penetrate and grow into the breathable fabric. Once penetrated, the roots are exposed to air, which causes the tips of the root to dehydrate and naturally prune themselves. This natural pruning process forces the roots to grow tons of lateral fibrous feeder roots. This results in a plant that utilizes the entire root zone and fills the entire pot with tons of roots. These fibrous feeder roots are incredibly effective in uptaking water and nutrients, resulting in a plant that grows healthier and more vigorously! Oxygen Benefits- Without oxygen, nutrient absorption cannot occur. On a molecular level, oxygen is needed to transmit nutrients across the cell walls and into the roots of a plant. With the AirCube's proprietary bottom lifted draining design, the system actively draws all of the water out of the bucket pulls vital oxygen into the root zone. Maximum Versatility with Any Grow Medium: The AirCube System is the only system on the market that allows you to use any growing medium you like. Use coco coir, soil, peat moss, perlite, vermiculite, hydroton, rockwool or any other medium you wish! This system is the most versatile Ebb and Flow bucket system in today's hydroponics industry. Temperature Control- with the fabric pots constructed with highly porous polypropylene fabric, heat dissipates easily and effectively. Unlike standard plastic pots, heat isn't trapped in the root zone. Heat in standard plastic containers can reach temperatures of up to 125 degrees. When this type of heat is trapped and unable to escape, it can damage your plant's health and limit the potential of your harvest. Growing in the AirCube System, plant roots grow cooler, healthier, and more vigorous. Largest Pots in its Class- this system features 5 Gallon grow buckets, the largest pot size of any other ebb and flow hydroponic system in the market. Modular and Expandable- start with 6 grow buckets and expand up to 36 grow buckets with the optional 105 gallons PopTank reservoir!" For my medium and nutrients I decided to also switch things up from my regular Organic runs, going with Plagron Nutrients and Root Royale 70/30 Coco/Perlite. When filling the fabric pots with medium, I first added just under a gallon of horticulture perlite from Nor-Cal as a base layer to ensure good drainage and then filled the remainder with the Root Royale. •Now for one of my favorites, and award winning strain from my friends at FastBuds... Strawberry Gorilla Auto: I'll be running Strawberry Gorilla Autoflower which is a 55/45 Sativa/Indica Hybrid. "ATTENTION ALL! Due to our continuous efforts in evolving our breeding process, we are proud to confirm that our Strawberry Gorilla Auto has now become one of the most potent autoflowers in the world! Paving the way to our recent success where she ranked on top & brought home the gold at the very first American Autoflower Cup in California. Moreover, she proved that not only modern autoflowers can compete with photoperiods, but they can even beat them in their field. At the most recent edition of the Farmer’s Cup and competing against various photoperiodic strains, Strawberry Gorilla Auto took home the title of 'Highest Combined Terpenes' in the highly sought-after 'Home Grow Hash' category, with an impressive 97.163 mg/g total terpene content! Our exceptional genetic selection's crowning Strawberry Gorilla Auto strain is a spectacular hybrid known for producing yields of up to 600 gr/m2 in 70 days. This is a very manageable grow that can reach heights of up to 150 cm - due to its magnitude we recommend it for more experienced growers, as a huge plant may be a little overwhelming for first-timers. This show stopping sativa heavy hybrid is perfect as an all day smoke, producing a taste bud tingling, pungent berry and diesel terpene-rich flavor combo that leaves you with a grin from ear to ear, a perfect choice for those looking for a day-and-night autoflower! "* *References: GrowAce.com, 2fast4buds.com ______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ The Setup: • AC Infinity 4x4 tent •AC Infinity Cloudline T6 Exhaust Fan w/ Controller 67 •HLG 650R w/UVA Bar *** For some reason GD does NOT have a listing for the USA version of the 650R so I selected the closest match to it. •AirCube Active Oxygen Ebb/Flow 6 pot System •TrolMaster Hydro-X Controller for light •AutoPilot APC8200 co2 controller fed by a 50# tank •16" Hurricane oscillating fan and 8" floor fan •Tent cooling via filtered outside air delivered by AC Infinity Cloudline T6 fan •BlueLab instruments: PH Pen and Truncheon Nutrient Meter ______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ Weekly Updates: 10/10- Here we go again with another killer strain from FastBuds, Strawberry Gorilla! I went ahead and germinated 4 seeds originally by first soaking in a glass of tap water for 12 hours then placing in pre-moistened Peat Pellets, of which all four were successful. Two however looked like they they might not make it, so I germinated 3 more by first soaking for 12 hours, then placed on moist paper towels for 48 hours. I checked them on the third day and all had sprouted. I then planted the additional 3 seedlings next to the ones already in pots and will wait 5-7 days to see which look the best, then cull the 3 'losers'. 10/12- Yesterday, I went ahead and ran the AirCube system manually today to give them their first feed. I have the reservoir filled with 60L of well water which was adjusted to 6.2ph @ 75℉. I then added 60ml each of Plagron Cocos 'A' and Cocos 'B' and 30ml of Plagron Power Roots to the reservoir and, after mixing thoroughly, readjusted the ph to 6.3 @ 75℉. I then ran the AirCube system on the 'Fill' setting for 10 minutes. While the system was filling the pots, I used a soil hydrometer to monitor the moisture level in the medium to make sure that I had the floats in the 'Brain Bucket' that control how much solution flows through the system adjusted correctly. Everything worked flawlessly with all of the pots getting saturated, then fully drained... excellent! 10/14- I ran the AirCube system again today after checking the ph of the reservoir which had risen to 8.0 due to off gassing of CO2 which occurs because of the large air stone I have in the reservoir to oxygenate the water in it. I adjusted the ph to 6.2 using SaferGrow's PH Down which BTW I love! After adjusting the ph, I ran the system manually for 10min, then drained it. I have the HLG 650R hung @ 28" above canopy and have it set to 45% power on a 19/5 cycle via a TrolMaster HydroX Controller. Tent temp's are running 80-82℉ with the lights on, 74-75℉ during the dark cycle. RH is being maintained by a 1.5g humidifier at 63% currently resulting in a 1.41kPa VPD. 10/17- Well there goes the first week for these three girls and so far, so good! They all have good color and leaf structure and I'm just waiting for them to take off now. I ran one manual feed cycle today for 15min upping the ppm's to 700, then drained the pots. I'll start gradually increasing the feed schedule along with the ppm of the nutrients starting next week... See you there!💚
Processing
Likes
41
Share
Welcome to the Sweet Seeds Cup 🏆 Hey everyone :-). This week she started to put her full power into the flower production :-). Since then she has received Canna Bio Flores and Canna Bio Boost 🤗. It is barely one meter high and looks beautiful 😍. In addition, it starts to smell very delicious 👍. I water it about every 3 days with about 1 l - 1.5 l. It is very stable genetically and I'm glad I took cuttings 😅 . I am very curious to see how it will develop next week. I wish you all a good start into the new week, stay healthy 🙏🏻 and let it grow 🌱 Sweet Seeds Cup 🏆 Type: San Fernando Lemon Kush ☝️🏼 Genetics: OG Kush x Kosher Kush 👍 Vega lamp: 2 x Todogrow Led Quantum Board 100 W 💡 Bloom Lamp : 2 x Todogrow Led Cxb 3590 COB 3500 K 205W 💡💡☝️🏼 Earth: Canna Bio ☝️🏼 Fertilizer: Canna Bio ☝️🏼🌱 Water: Osmosis water mixed with normal water (24 hours stale that the chlorine evaporates) to 0.2 EC. Add Cal / Mag to 0.4 Ec Ph with Organic Ph - to 6.0 - 6.3 💦💧
Likes
4
Share
@Lazuli
Follow
Feeding 850ppm every 2 days runoff @700ppm
Likes
4
Share
Wow guys, look at all this sugar leaking out of these buds! I'm going to end up doing like Winnie the Pooh when I put my hand in the jar! I already know it!😅😅😅😅
Likes
47
Share
@Dynab000
Follow
Perfect and easy to grow, thankful no pests this round. Had no issues at all. It was such and easy grow and will definitely grow this again. Love it
Processing
Likes
7
Share
@SybDarret
Follow
I'm kinda late on the update, week 11 finished on sunday 4, now is feb 9th. Last time i gave them nutrients was on sunday jan 28th, and i cut them down on feb 6th. almost a week and a half of flush. Each plant yielded 65g of wet buds (i forgot to take wet weight photography), i will update the harvest when they are done drying and before curing. Stay alert 😉
Likes
11
Share
@TgOgFaRms
Follow
🌿🌸 Week 4 Flowering Update! 🌸🌿 We have officially entered week 4 of the flowering phase, a crucial period where things can get a little nerve-wracking. However, I'm happy to share that everything is looking great so far! 🎉 First off, let me express my relief that I haven't encountered any hermaphroditism issues like some unfortunate growers have experienced. I've been extra vigilant in checking my plants for any signs of bananas or seeds, and thankfully, all is going smoothly on that front. Fingers crossed, and let's hope it stays that way. 🤞 Now, let's talk about the progress of these beauties. The plants are thriving, exhibiting vigorous growth and magnificent stretching. 🌱✨ Maintaining the well-being of my plants remains my top priority. They're displaying a healthy thirst, as each plant continues to drink around 2 liters of water every two days. I've been closely monitoring the pH level of the nutrient solution, which has been steady at 6.11. This ensures optimal nutrient uptake and keeps the plants in their prime condition. Moreover, the TDS range is consistently between 1050 and 1150, providing them with the ideal nutrient balance. ⚖️💧 Speaking of the plants, I must mention how amazing they smell! The aroma is becoming more intense with each passing day. Today, I conducted a smell test for the OG and Oreo strains. The OG emitted a super strong smell of OG/Skywalker, while the Oreo strain has a unique and captivating scent that is difficult to describe but absolutely amazing. I can't wait to smoke that one! Tomorrow, I'll do a smell test for the Queen strain as well. 🌿👃🔥 As we progress through this crucial stage, I'll continue to provide the best care possible to ensure a successful harvest. Today (Day 22) marks the last day of foliar feeding with Bud Factor X, an essential step to maximize THC development and quality. This phase demands attention to detail and careful observation. 👀🌿💦 That wraps up this week's update, fellow growers! Keep your fingers crossed for a smooth journey ahead, and may your own gardens thrive. 🤞🌿🌸 Happy growing, lads! 🌱💚
Likes
92
Share
Week 4 Veg Report - TrolMaster Chronicles 🌱 What a week it’s been in the garden! We finally transplanted the Papaya Zoap into its final Autopot, and let me tell you, this plant is something special. Though her roots weren’t quite where I wanted them to be yet, the move was needed to help her catch up with the rest of the crew. She’s already looking fantastic in her new home, and I have no doubt she’s about to explode with growth in the coming days. Sometimes, you just have to trust the process, and I’m feeling like this is one of those moments. It’s almost as if the room itself is taking on a life of its own. 🌿 In fact, I’m starting to believe that what we’re building here is something greater than ourselves—there’s this energy in the room, a feeling of everything coming together perfectly. I can’t wait to see how this journey unfolds! Dialing in the VPD with TrolMaster’s Tech Now, let’s talk VPD (Vapor Pressure Deficit) and how I’ve been keeping everything in check with the Tend-X and the incredible (DSH-2U) Humidity Station. VPD is crucial to plant health—it’s all about finding that perfect balance between humidity and temperature to optimize transpiration and nutrient uptake. The (DSH-2U) Humidity Station, connected directly to my humidifier, has been an absolute game-changer in this regard. With its real-time data and automation, it allows me to monitor and adjust the RH with pinpoint accuracy. Simple yet brilliant, the (DSH-2U) Humidity Station is keeping my room at the sweet spot I need. Whether I’m tweaking the settings from my phone while I’m out and about or just fine-tuning things while relaxing at home, this machine does it all. It’s like having an extra pair of hands in the grow room—and when you’re managing something as complex as VPD, that’s invaluable! And yes, the TM+ Pro App—let’s not forget how awesome it is. I’m adjusting my grow room from the couch, the car, or even the bathroom 😜. I’ve said it before, but this app is making growing easier than ever. Feeding the Girls: The Perfect Blend 🌱 We’ve upped the game by adding CaMg-Boost at 0.25 ml/L to the feeding schedule. Along with the 1 ml/L of the all-in-one liquid, this brings the TDS up to 320 ppm, with a pH of 5.99 and solution temperature of 24.8°C. In the soil, readings are around 415 ppm, with temperatures hovering around 25°C The plants are absolutely thriving, and I can already see the difference this new feed is making. I can’t help but have a bit of fun with this process—it feels like I’m spoiling them with the best of the best. And they’re rewarding me with beautiful growth and vibrant green color. You know how it is, with the right care and attention, these plants are truly becoming a masterpiece in the making. 🌱 Shoutouts 💚 Big shoutout to TrolMaster and ThinkGrow LED for the phenomenal gear that’s making this grow smoother than ever. Also, massive thanks to Aptus Holland for their top-notch nutrition, and of course, to the community here on GrowDiaries—you guys keep the energy alive! 🌱 Last but definitely not least, shoutout to all the seed banks supporting this journey. You’ve been a huge part of this process, and I couldn’t do it without you! Remember, for exclusive behind-the-scenes content and updates in real time, head over to my Instagram and YouTube channels @DogDoctorOfficial. We’ve got tons of epic content lined up, and you won’t want to miss it! P.S. Let’s talk about the new Model One LED Bars—these beauties are not only powerful but super efficient. I’ve been able to dim them down, save on electricity costs, and still maintain an incredible PAR and spectrum. It’s all about fine-tuning the balance of power and performance, and these lights make it easy to get the best results while being eco-friendly. Whether you’re running them full throttle or dialing it back, you’re still getting optimal growth conditions for your plants. That’s the kind of innovation that takes your grow to the next level. 💡 Growers Love to all 🌿💚
Likes
8
Share
@Kappa420
Follow
So, every plant goes with its rhythm... I think no1 is about to be harvest or are least flush now. Small yield for sure but plants seem to be ok.
Processing
Likes
4
Share
So the at the start of week 4 the girls have taken a beating from the pesticide that I spray on them, had to take off some dying fan leaves. the one plant is recovering nicely while her sister on the other hands need a close eye. This week the girls will get their first watering with actual noots
Likes
8
Share
Hello growers day 63 in the garden with blue monster auto she’s just getting beefy now the buds are full of resin she is popping off the weather is banging right now in the uk so she loving life outside I’m going to start flushing now so she should be ready very soon I’ll keep an eye on the trics and wait for amber to start showing so until next week be safe and happy growing ✌️