Likes
3
Share
@CalGonJim
Follow
4/13 10AM MONDAY They are looking pretty good. Got the ph stabilized and only running 98W! Using a few DROPS in 18oz to test Purpinator on veggies. 4/14 11am Using a little Purpinator .5ml per gallon and will have to do lots of runoff to prevent burns. Using vegetables to test fro Purpinator burns👍 4/15🚨🚨🚨 Your setup photos are great — thanks for sharing them. The R2-D2 power strip topper is a fun touch (he’s guarding the outlet like a proper astromech droid). Here’s a clear breakdown of what I see and my honest opinion on the power draw/safety. What you’re running • Two Mars Hydro TS1000 lights — These are officially rated at 150W each (real-world draw is usually ~145–150W at full power, sometimes a bit less if dimmed). You mentioned ~100W each, but they’re actually higher — so total for the two lights is roughly 300W. • Plus the two black fan speed controllers (one for each tent’s exhaust/inline fan). • A few small wall warts/adapters plugged into the white smart plugs or directly. • You measured 335W total across tents 1 and 2 on one outlet — that lines up reasonably (lights ~300W + fans/controllers ~20–40W depending on speed + minor losses). Is this safe on one standard outlet/circuit? In most US homes a standard wall outlet is on a 15-amp 120V circuit: • Max theoretical capacity = 15A × 120V = 1,800W. • Safe continuous load rule (National Electrical Code for things running 3+ hours, like grow lights): Stay under 80% = 1,440W max. Your 335W total is very low — only about 23% of the safe limit. That’s comfortably safe. No real risk of overheating the outlet, tripping the breaker, or fire hazard from overload right now. My opinion on the setup: • Good: Everything is neatly plugged in. The white smart plugs (with the green lights and blue indicator) and the labeled ones (9e, 10e, 11e) look like you’re using them for timers or monitoring — smart move for controlling lights/fans independently. R2-D2 adds personality and keeps the wall organized. • Fine for now: Two TS1000s + fans on one outlet/circuit is no problem at these low watts. Many small grows run similar loads without issue. • Long-term suggestions (to keep it safe and reliable as your grows expand): ◦ Don’t daisy-chain too much — You already have multiple adapters and controllers stacked. Avoid adding a lot more (e.g., dehumidifier, heater, or more lights) on the same outlet/circuit. ◦ Check heat — Feel the wall outlet and the power strips after the lights have been running for a few hours. They should be only slightly warm, not hot. If anything feels warm/hot, spread the load. ◦ Dedicated circuit is ideal — For peace of mind, run the lights on their own circuit if possible (or at least separate the fans/controllers if you add more equipment later). ◦ Surge protection — Make sure the main power strip or outlet has good surge protection, especially with grow equipment that can have inrush current when turning on. ◦ Monitor actual draw — Your 335W reading is helpful. If you have a kill-a-watt meter or smart plug that shows real-time watts, keep an eye on it when everything is at full power. The houndstooth shirt hanging on tent 2 is a nice personal touch — makes the grow room feel lived-in and less sterile. Quick safety checklist for your whole setup • All cords are in good shape (no fraying, especially the black ones going to the fans). • Nothing is blocking airflow around the plugs/adapters. • The inline fans and ducting look properly attached (important for heat and smell control). • If you ever add more lights or equipment, recalculate the total watts and stay under ~1,200–1,400W on that circuit. Overall, your power setup looks thoughtful and creative (love the R2-D2 detail). It’s not overloaded at 335W, so you’re good to keep running tents 1 and 2 like this while you sterilize and prep tent 3.
Likes
25
Share
@Jimmy89
Follow
All looking happy, photos taken day 33 of flower. Never got around to defoliating this week, been locked in trim jail I take the photos with the lights dimmed right down, not sure how some of you get such good photos.. Happy growing ✌️
Likes
16
Share
@valiotoro
Follow
Blessed with the result as you can see the buds looks fantastic💎 The trim was super easy(make sure you have enough gloves)😂 Now 7-10 days on the dry rack then see you in 2025 for the smoke review Take care😁
Likes
7
Share
Day 37 (from sprout): the last two days, were really hot and the humidity increased to an uncomfortable value of 60-70%. Today I tried to lower the humidity with more ventilation, keeping the tent open and reinstalling a pot cover I had previously removed from the pot in the back. Furthermore, I made sure to give the girls another intense trim.
Likes
8
Share
@Kirsten
Follow
26.4.25: The plants were watered with 3 ltrs of dechlorinated water PH'd to 6.3, containing the following nutrients:- ♡ 1/2 Tsp Sea K(elp) by Greenleaf nutrients ♡ 1/4 Tsp Ecothrive Biosys. 27.4.25: I LST'd again by adjusting the tie downs. For FastBuds Mystery seed auto #1 and RQS Northern Lights autoflower, this will probably be the last time I adjust the fabric ties, as they're now well in to flower. Keeping the canopy as even as possible. 29.4.25: FastBuds Mystery seed #1 has taken very quickly to the readjustment of the fabric ties. Within an hour, the plant had already grown back towards the light. That's always so crazy to me. I watered 3 litres 2 days ago, and I'm not going to water again until it has dried. I suspect that will be at the end of the week. The larger pots are a learning curve with trying to water adequately but not too much. I don't think that I've ever overwatered, I never water to run off. This time came uncomfortably close though Thanks for checking my diary and hanging out 💚✌️🍃😊🌱
Likes
6
Share
Normally I allow two days in the paper towel germination. This one after only 24 hours.
Likes
132
Share
📅 Week 8 | 🗓️ Days 50–56 – Start of week 9 | first signs of flowering 🌸 Day 56 - Papayton 🚀🏀 🔸 Very vigorous this week: broad, even canopy with lots of tops; the stem is solid with nice “knuckles” from training. Lower shoots are tidy – air and light are getting through well. Leaves are rich green, upright, and without burns. The first pistils are appearing at the nodes and tips – the transition to flowering has begun. 🔸 Setup: on 12/12 since day 50. With ~700 PPFD approx. DLI ≈ 30 mol/m²/day – ideal for stretch/transition. Maintain a distance of ~40 cm and adjust during stretch. Over the next few days, I will increase to approximately 900 PPFD. 🔸Biotabs & water only: continue as before. Keep pH at around 6.2, maintain even moisture (no hard drybacks). Only add more if there are clear signs of deficiency – otherwise, don't force anything. 🔸In week 9, small flower clusters should form; if necessary, lightly defoliate and provide support sticks/trellis so that the tops can start cleanly. 📈 Current Conditions 🌡️🔆 = 24°C 🌡️🌜 = 19°C 💨 Humidity = 60% 🔦 PPFD = 700 µmol (12/12) 🛠️ Setup (unchanged) 💡 2 x SANlight Evo 4 - 120 @ 80% ⛺ 120 x120 x 180 Spiderfarmer 🍯 Pots: 18 liter fabric pots 🌱 Soil: Bio-Bizz light mix 💊 Nutrients: BIO Tabs only water method 💧 Water: Tap Water 0,5 EC 🌱 “Easy, organic, only-water method. Save 15% with GDBT420. biotabs.nl/en/shop/”
Likes
Comments
Share
@UGrowGuy
Follow
01/11 Girls are blowing up. About mid stretch. True week one of flower 01/12 Switched out the MH for the HPS. They are running at 1150w with the UVBs. I will be adding some LED to mix the spectrum up a little more, plus i feel like they want more light even though its nuclear in there. They had a couple drinks of H2O this week. PH’ed to 6.0 using the bokashi/ffj. These plants wreak soo good when i brush up against them. IMO-The Bokashi/ffj adds soo much!!
Likes
13
Share
@Rob96
Follow
Cut screen down now as all stems hardened and in place. Had a good shuffle around and as the Dos Si Dos 33 height was taking over the rest ive raised my lights and put the other 3 on top of boxes to raise up more level. Really pleased with everything, had to do a little late trimming as plants are all so bushy but now everything set for them to just grow freely untouched. Starting to fatten up and got plenty of top bud sights fingers crossed in for a good yeild and so far the quality is there. This Purple Punch has come on really well and is showing no issues and looks to be really healthy and strong
Likes
28
Share
@Sators
Follow
Hi, good fellows!💚 🌱Day 72. Watering with 3.1L 6.7ph 150ppm clear water. Run off water get 90ml 6.7ph 300ppm. Leaves more indicates nutrients deficiency.💚 🌱Day 74. Watering with 3.5L 6.4ph 150ppm clear water. Run off water get 165ml 6.5ph 300ppm.💚 🌱Day 75. Due to mistake, because some time too high🤣💚, watering with 2.5L 6.4ph 150ppm clear water one day earlier. 😂💚 Run off water get 165ml 6.1ph 400ppm. Add some video.💚
Likes
39
Share
End of the first week of using the shooting powder and the plants are loving it and took the higher EC level with no problems, running slightly higher PH levels to help with the uptake of P and K. Looking like it’s going to be a really good run
Likes
114
Share
@Drgreen13
Follow
Hello everyone, well, she seams like she wants to flower and it shouldn't be long now before she transitions. I've strapped her main branches down and defo'd a little, all in all, no problems as of yet and very easy to grow. Very fast also. If you would like to order this strain or many more, then head on over to www.doctorschoice.farm and enter promo code drgreen13 to receive 15% off your order. (CODE VALID UNTIL 31.07.22) I HAVE A COMPETITION RUNNING, ALL YOU HAVE TO DO TO ENTER IS FOLLOW ME AND LIKE THIS DIARY, ENDS 31.07.22 GOOD LUCK TO EVERYONE. stay high, stay fly. #420everyday.
Likes
24
Share
@Doubleb84
Follow
Great harvest! Ended up a little shy of 12 ounces from the two plants, all super dense sticky top buds!! It’s smooth, flavorful and strong! Love it!
Processing
Likes
49
Share
Hi everyone 🤗. She is getting bushier 😅. I decided to have them in the 11 liter pots. Since it is getting pretty tight in the flower tent 😀. In about 10 days there will be some space in the flower tent, then I will move it around 👍🙂. Until then, I wish you all a nice weekend 😎 stay healthy 🙏🏻 and let it grow 🌱 You can buy this Strain at : www.Zamnesia.com Strain : Sour Diesel ☝️🏼😍 Genetic: Diesel x Northern Lights 👍 Vega Lights : 2 x Todogrow Led Quantum Board 100 W 💡 Flower Lights : 2 x Todogrow Led Cxb 3590 COB 3500 K 205 W 💡 ☝️ Soil : Canna Terra Professional + ☝️ Nutrients : Canna Terra Vega, Canna Terra Flores, Rizotonic, Cannazym, CANNA Boost, Pk 13/14, Canna Cal/Mag, Canna Ph - Grow, Canna Ph - Flores ☝️ 🌱 Water: Osmosis water mixed with normal water (24 hours stale that the chlorine evaporates) to 0.2 EG. Add Cal / Mag to 0.4 Ec Ph with Organic Ph - to 6.0 💦 💧
Likes
35
Share
Venga familia que ya viene la cosecha de estas Cereal Milk de RoyalQueenSeeds, que ganas que tenia ya de darles machetazo. No veas que pinta que tienen estas plantas. Las flores aparte de prietas se ven bien resinosas, con 70 dias de floración. a sido una genética con la que disfruté mucho cultivarla, es resistente , y no es para nada complicado cultivarla por lo menos en interior. Agrobeta: https://www.agrobeta.com/agrobetatiendaonline/36-abonos-canamo Mars hydro: Code discount: EL420 https://www.mars-hydro.com/ Hasta aquí es todo , espero que lo disfrutéis, buenos humos 💨💨.
Likes
112
Share
@Dunk_Junk
Follow
Still waiting for trichomes to turn all cloudy. Seems to be taking forever! Many leaves are yellowing now so she is close to the end for sure.
Likes
9
Share
Check out my grow series, From Seed To Smoke, on YouTube. https://youtu.be/THYTLQyGPVQ What an amazing week! These ladies have been growing tremendously! It's only 3 weeks today from when the seed packs were opened. Pretty incredible if you ask me. If you're curious, I kept the nutes at about 1/8 to 1/4 strength until transplant. That's when I upped nutes according to my chart.
Likes
8
Share
@Random80
Follow
Again I did not connect her on autopot but soaked the soil with loads of water and left wet towels all around the bottom of the tent to keep humidity since capacity of my humidifier is just one day. My idea was that she will use all the water in the pot and nicely dry out the root until I am back next time and in the meantime wet towels on the bottom of the tent will keep air humidity for first few days and than I can switch ON my humidifier remotely for last day, if needed (I am using alfred camera app and my old phone inside of the tent to be able to keep an eye on conditions while I am absent however I can only remotely control humidifier). Turns out (AGAIN) that it was too much water and she did not manage to use all of it during this 5 days. I found the top of the soil to be completely dried out while at the bottom of the pot and by the weight I would guess that there was still plenty of water available. I am using guanokalong soil that normally spreads water and humidity very nicely so I was bit surprised about such a difference from top to bottom of the pot. Overwatering signs are visible on young leaves; they became soft and start curling down got darker color. Despite that I have added 0,5 lit water (with orgatrex) just to balance the humidity in the pot. I am here only for day and a half and after that I will be gone for 10 days. Will not be able to dry out the soil before connecting autopot so more problems related with overwatering can be expected next time I am back. Will try to calculate quantity of water needed for 10 day and fill the tank of autopot with just a bit less than that so she can recover from all that water at one point.
Likes
7
Share
Hey everyone 🤗. This week you really put your energy into your growth 👍. They look beautiful, thanks also to the nutrients in Green Buzz Liquids 😍👌. Next week she will be moved to the flower tent 👍. I wish you lots of fun with the update, stay healthy and let it grow 😎 You can buy this Strain at https://thecaliconnection.com/original-sour-diesel.html You can buy this Nutrients at https://greenbuzzliquids.com/ Type: Original Sour Diesel ( Clone ) ☝️🏼 Genetics: Fem seeds- Original Sour Diesel to Original Sour Diesel BX3 RVSD Male Reg seeds- Original Sour Diesel x Original Sour Diesel BX3 Male 👍 Vega lamp: 2 x Todogrow Led Quantum Board 100 W 💡 Bloom Lamp : 2 x Todogrow Led Cxb 3590 COB 3500 K 205W 💡💡☝️🏼 Soil : Canna Coco Professional + ☝️🏼 Fertilizer: Green Buzz Liquids : Organic Grow Liquid Organic Bloom Liquid Organic more PK More Roots Fast Buds Humic Acid Plus Growzyme Big Fruits Clean Fruits Cal / Mag Organic Ph - Pulver ☝️🏼🌱 Water: Osmosis water mixed with normal water (24 hours stale that the chlorine evaporates) to 0.2 - 0.4 EC. Add Cal / Mag 2 ml per l water every 2 waterings . Ph with Organic Ph - Pulver to 5.8 .
Likes
30
Share
This week was absolutely torturous had an accident in which one of my plants was damaged fortunately I do not believe that all is lost I will just have to hold her back on sending her into flour with the rest until she is completely healthy I have sent one into flower a bit early just to see if I could and seems to be working swimmingly