Likes
Comments
Share
She is definitely performing. I can smell her on approach. The weather does not look too promising for the next 72 hours…hoping for the best this post full moon rain.
Likes
44
Share
👉The time finally arrived for the harvest, mostly cloudy trichomes with scant few amber, very few white pistols, and the leaves had either faded or were fading. The run-off pH would quickly plummet and the run-off EC would spike. This may be an indicator that the plant is ready but that only would be conjecture on my part. The overall look of the plant to me said it was ready. The aroma was super strong citrusy and intoxicating. THe leaves were fading and there were virtually no white pistols. 👉I harvested bottom to top. I hung each cola on alphabetized clothes pins with gardening wire attached for hanging on the rack. The buds are dense and shaped like pine cones. I trimmed it semi-tight, but left some of the smaller frosty sugar leaves. The buds and sugar leaves are very frosty but it wasn’t as scissor freezing as the Gorrila Glue I grew last year. I measured the post trim wet weight on a self-calibrating digital scale. I checked the accuracy of the scale with a set of scale calibration weights and it was accurate at all weight ranges. I logged each colas trimmed wet weight and hung on the rack. I have a 42” tower fan. For first 12 hours I ran it at its medium setting, then reduced to lowest speed. I rotated the side facing the fan after 24hrs. Then after another 24 hrs I placed them in paper sacks with to top open. I left the buds on the clothes pin hanger and clipped the bag to that. After another 24 hours I closed the tops. Another 24 hrs and I test weighed a couple of colas. I monitored for another couple of days until the weights averaged 20-25% reduced from the initial wet weight. I then cataloged the weight of each cola and placed each into its own jar, most got one of those small cheap hygrometers. These hygrometers have been calibration tested and I know the drift of each. My target humidity is 62%. I would open the jars for brief periods of time during the next couple of days until the humidity stabilized at 62%. Once stable I placed 62% humidity packs in the jars. I took out most of the hygrometers for the next plants cure, but leave some of them with the best buds. The Queen cola was 20g when placed in the jar. That is about 24% remaining weight from trim. 24% is a little on the high side of the humidity target range. The jar the Queen cola is in, is a wide mouth counter jar and I will be toking that bud primarily and it will dry out the fastest. I have compensated the weight I entered on the dry weight spec to reflect about 20g more of humidity loss and another 30 for the stems that are left on the bigger buds. The final weight of the buds going into the jars was 254g (not including the larf at 23gdry). 200g of plump sticky pine cones for the final weight is pretty nice for a 1 gallon pot. 👉I wrote this review at 3 weeks before the 6 week cure mark. In my short experience of being weed rich, its been interesting to take note of how the flower continues to ‘cure’ as time goes on. I have found that 6 weeks isn’t a given for when its ‘cured’. I have observed that as weed ages it changes. I have not noticed much difference with 2-3 week old buds at 62% humidity when compared to 6 weeks from jarring. But I do notice significant difference around 6 months of age. The flavor is enhanced and the buzz is stronger. It maintains this level then 8-12 months it has leveled off and all strains are becoming more ‘couch lock’ inducing. My observations are not scientific by any means. This is just my 8th plant in the 2 years that cannabis became legal for home grow in my area. But I still have each of the plants and rotate which one I consume. 👉I loved growing this plant, and hopefully gained more knowledge. It fox-tailed a bit at the end. I think my frequent fertigation techniques contributed to most of the issues I had. I think I was a little too conservative with nutrient mix and irrigation volume and frequency. I used only 10% expanded clay pebbles in the coco mix as opposed to the standard 30%. This was slightly problematic at first before the roots filled the pot. Fertigation events would cause erosion and caution had to be taken around the seedling. I placed a layer of hyrdoton pebbles across the surface and the issue was solved. Once the pot was filled with roots it took 10+ minutes to give the plant 2L of solution. The pot was packed hard with roots. This may have been a contributing factor to some of the possible nutrient issues I had. I dont think the nutrient issues I saw had much impact on the final outcome. To get 200g from a 1 gallon pot is wonderful.
Likes
7
Share
Watching the grass grow. No still shot for this week just a couple of videos.enjoy!
Likes
11
Share
End of Week 15 into Week 16. The Flush has begun. I Suspect She's within Her Last Week or 2 before Harvest so it's only PH Balanced Water until Harvest.
Likes
3
Share
@Cbartl420
Follow
My bottom leafs gettin a lil yellow but this plants doin really good for my first one gorilla wedding gone be sum fire tree the smell is amazing been watering with 1 liter had to put sticks into hold my plant up it was starting to fall out the pot
Likes
70
Share
All feeds with nutes use either a whole ratio, or combination, of "Veg Mix" and "Bloom Mix"concentrates. These are/will be DILUTED in water until a total ppm of add-in is reached using a (Total Dissolved Solids) TDS Meter measured in PPM (parts per million). The "Veg Mix" concentrate will eventually be added-in larger, then smaller, ratios while the "Bloom Mix" concentrate will eventually replace the "Veg Mix" concentrate entirely. The ppm and ratios will be listed when I feed. Veg mix recipe is on week 3. Bloom Mix recipe is on week 5. Day 91/21 Replaced the small modified tomato ring with a full size 3 ring tomato support ring so I could support every branch. I made this decision on seeing a lot of my 90 degree breaks from yesterday as still mostly 90 degrees. I also removed the tape from around the split and placed a wire tie under that trunk to ensure it was secure. After that I also placed a tie on each cola split just past my breaks and another higher up as an upper support. VPD was great aagain today. 74F/55%RH/ Auto ILV but raised the fan setting from 4 to 5 so it didnt have run as long to get it back into range. PPFD was a bit off yesterday and today from all of the sudden changes, But I raised my lights today and returned the settings to 750 max and 550 lowest. This meant that I needed to move my fans as well. They are now on medium setting and all were checked for movement to as many branches as they can hit. Day 92/22 Watered for salt flush today. Used 3 gallons of purified water at 7.1ph water no additives. PPM was about 70 after ph'd. Ended up with ~ 1.25 gallons of runoff that showed 5.95 and 5.98ph on two meters. Top soil tested at 6.44, 6.63, 6.36, and 6.47ph for an avg of 6.475. Runoff also showed 1540 ppm VPD was controlled with having the door open for a few hours. Temps and humidity are 72F and about 50%RH with the door open, and about 75F and 55%RH with it closed. ILV still on auto fan setting 5. PPFD was adjusted to 820 max and 600 lowest - I used 1 hour total of IR at mainlight on/off with 15 minutes before and after switch. She got another 45 minutes of UV today as well. I plan to increase to 1 hour tomorrow. Day 93/23 Week 3 of flower and most all is well. I did however find some light burn. I say light burn because the only conditions that changed was 15 minutes more UVA today and the spots are on the leaves closest to the light. Feed yesterday was plain ph water and it improved both the topsoil and bottom runoff ph so I dont think it's a nute issue. My solution is to take control pics and reduce UVA back to 45 for another day or two to see if the condition persists or advances. Otherwise PPFD was about 820 down to 600. I used 1 hour of UV and 1 hour of IR at lights on/off Other than that it was a lazy football day while I just leave her alone. VPD was normal with humidity easy to control at 55%RH or less and temps ranging from 74-76F during the day and down to 66-68F at night. Day 94/24 Checked in on "light burn" control leaves and took pictures. My analysis is to reduce lights a little more so now max is 795ish. Went ahead with 45 minutes of UV light at mid day and 1 hr IR on the same standard I have been using. Fans still on medium and since I dont believe the spots are related, I plan to leave them on that setting. Overall I dont see much need to change anything at the moment with the spots not getting much worse or at least not that noticeable other than what has happened already and I already reduced the lights a little. If I can identify any more new spots today or tomorrow I will reduce by another 25ppfd. And if not, then the next day I will try 1 hour of UVA again. Temps and Humidity are controlled at the same 74-76F and 55%RH or lower. My plan is to keep RH that level throughout and possibly try to reduce again to as close to 45% as I can get. (edited) Day 95/25 Reviewed suspected light burn and didnt see any progression either yesterday or today against my control pics from the day before. So I went with running UVA for 1 hr at mid day again today. Still using 1 hr IR on the same standard I have been using. VPD was good today with same settings of 73-76F and 55% or lower RH. Day 96/26 No issues to report today. She still has what looks like light burn on the older upper leaves, but doesnt really look to be getting worse and the lights are not getting brighter by growth anymore so I plan to leave them where they are and back them down if I see it get more progressive. Conditions in the tent are the same as yesterday... like little to no vertical growth in two 2 days and no need to change anything. I 'do' adjust the ties daily to ensure they are not creating a pressure point. Most aren't even supporting anything and some are just pushing the cola back or out from others. PPFD is 800 max and lowest is about 580. I ran 1 hr UVA midday with the same 1 hr IR at 30/30 with main light schedule that I have been running. Temps steady. 73-76F in the day and 66-68F after lights out. RH% is 55 or less with the fan on auto. 97/27 Watering day. Started by testing /calibrating meters. Used 2.5 gallons of de-chlorinated tap water with starting ppm of 227, added ~700ppm of 100% Bloom Mix concentrate (actually 686ppm added) and ph balanced feed to ~7.0 tested on two meters. Fed until bottom drip began and got ~7cups in runoff after about 10 minutes of drain. Runoff produced 2 meter tests of 5.8ph with 1520ppm. Top soil was tested 4 times for an avg of 6.3752. Next feed will be sooner, thinking like in 4 days instead of 5 and I can adjust if she seems to dry out again. I'll be looking for ~1/2 gallon of runoff to estimate next feed from. Light burn doesnt seem to be getting any worse. UV lights are doing 1 hr a day, midday, for the rest of the week and then I will increase a little per day each week until harvest. IR is still doing the same settings until harvest as well. 1 hour with 15/15 before and after main light schedule and 1 hr total. VPD is controlled with no issues of temps or RH exceeding set limits. 73-76F and 65-68F overnight with no more than 55%RH while the ILV is set to auto.
Likes
36
Share
@nonick123
Follow
Día 94 (02/09) Aplico Insect Frass como Top Dress para ver si revierto un poco el amarilleamiento que muestran algunas hojas, ya que empieza a ascender por la planta Riego con 500 ml H2O pH 6,5 Día 95 (03/09) Dia nublado y de temperaturas entorno a 24 ºC. NO es necesario regar! Día 96 (04/09) Llueve que te llueve! 🌧️. Temperatura 21 ºC. Dias de humedad alta por aquí! Riego con 500 / 1000 ml H2O pH 6,5 Día 97 (05/09) Floración en progreso. No veo ni una sola oruga con el bacillus thuringiensis y espero que siga así! 🤞 Dia muy nublado. No hace falta riego Día 98 (06/09) Riego con 500 / 1000 ml H2O pH 6,5 + 4 ml/L de BioGrow de Biobizz para tratar de parar el amarilleamiento que asciende por la planta Día 99 (07/09) Riego con 500 / 1000 ml H2O pH 6,5 + 4 ml/L de BioGrow de Biobizz para tratar de parar el amarilleamiento que asciende por la planta Día 100 (08/09) Riego con 1 Litro de Té Floración de Lurpe Solutions. Preparación: 24 horas con bomba de aire (oxigenación) con ingredientes: Healthy Harvest 8 ml/L + Insect Frass 16 ml/L + Hummus Lombriz 8 ml/L + Melaza 1 ml/L + Kelp Hidrolizado 0,25 g/L Aplico de nuevo Insect Frass como Top Dress 💦Nutrients by Lurpe Solutions - www.lurpenaturalsolutions.com 🌱Substrate PRO-MIX HP BACILLUS + MYCORRHIZAE - www.pthorticulture.com/en/products/pro-mix-hp-biostimulant-plus-mycorrhizae
Likes
4
Share
She's developing very fast and without any type of issues, there's not too much to say on the first days of life. I'm so excited about this indoor run. I'll be training this lady in not too long. Hope to make a big bush with this beautiful lady right here. Stay tuned to see this beautiful strain in action! 💎💚❤️💛👨‍🌾✌️
Likes
346
Share
@Canna96
Follow
This week went pretty well for my sour diesel auto. She Finally stopped growing vertically at about 48 inches to the top of the highest cola. We did have a serious heatwave and high humidity I been dealing with as well, but so far so good. The only thing I changed this week with nutrients is I raised my ec value to 1.6, at the advice of another grower, and the sour diesel took it like the piglet that she is. I am still on an 18/6 light cycle,which I plan to stay with the entire grow, and still feeding Maxibloom, calmag, and koolbloom. I am seeing some bright orange colored spots on the top leaves, but I am hoping it is just a little light bleaching. I have no experience with this as I have NEVER grown anything indoors before other than vegetable seedlings. I just wanted to say thank you to this community for all the advice, tips and encouragement along the way, very much appreciated all, and Blaze On!
Likes
21
Share
Week 13 was harvest time for two of the Bruce Banner plants 🌸✂️ #2 and #3 were clearly ready, with mostly milky trichomes and some amber, so I decided to finish them this week. Both plants were taken out of the tent on Thursday and placed into complete darkness for 48 hours. Due to the heavy buds, they had to be secured to the ceiling, as they would have tipped over otherwise. After the dark period, both plants were cut on Saturday and hung to dry 🌿 Only the large fan leaves were removed at harvest, while the smaller leaves were left on to ensure a slower and more even drying process. Bud structure is very dense and compact, with strong resin production and loud terpenes already noticeable at harvest. Aroma is a mix of chemical, citrus and sweet notes, very typical for Bruce Banner. Bruce Banner #1 stayed in the tent this week, as she was still slightly behind in maturity and needed more time to finish. Environment (before harvest): Temp ~24°C RH ~50–55% Overall a very smooth and controlled harvest week. Plants finished strong, and the quality looks very promising going into drying and curing ❄️🌱
Likes
41
Share
@AlphaNoob
Follow
Lovely body high on this one! Amazing for pain relief! Nice head too, taste and smell 10/10. Little yield but that was probably because of my mess ups throughout the grow. Overall a great strain Only yielded 9gs, was a small plant but no doubt I stressed it along the way so I think it’s more down to my mistakes than the genetics Tastes of grapey diesel, 10/10 🍇 Smells of straight grapes, 10/10 🍇 Appearance, very frosty and great looking bud(could be trimmed better but that’s on me)! 9/10
Likes
8
Share
Welp. I honestly didn't expect this. As I have mentioned in previous posts, this plant was no longer on its own timeline, the next plant was going to decide. In addition to this, I had just done a heavy defol and put the leaves and 3 small nugs in my cannatrol. The cannatrol still had 2 days before finishing its dry, so this ended up being interrupted. In some unfortunate mishap, as shown in the pictures, my light was scheduled to turn off at 5am. The device said it did, but as you see in the graph, it stayed on until I had caught it at 12:24pm. I simply disconnected the usbc from the outlet, reconnected it, my light kicked on for a sec, then back off. I think messing with my dehumidifier lastnight glitched the system and I should've done a reset when I was done messing with it. With the stress already playing a chance at mutations, the additional light didnt help. No hurt feelings here. With the weight off the bud and the sugar leaves, my cannatrol is maxed. 2.2 lbs of wet weight is all it can take, and I am pushing that. 900 grams of wet, partially trimmed buds impressed me! Not sure the sugar leave weight. Setting cannatrol to dry for 5 days and cure for 25. I know it can go way quicker, but I read a study about these settings and want to see if it stands any truth. Smoke report and dry weight coming soon!
Likes
10
Share
Likes
1
Share
Yet another beautiful creation from Humboldt Seed Company. Huge trichome heads, amazing, complex aroma. Oh and did I mention magnificent leaf and bud colouration? They are purple AF 💪 I love them sooo much 😍😍😍
Likes
16
Share
@Mrg7667
Follow
I finally feel like we are getting some good vertical growth! And all cut spots have put on at least 2inches. So i flipped into flower this is day 1-0
Likes
Comments
Share
Likes
23
Share
@Gram_Solo
Follow
Tick followed tock Starting to fatten up now 👽🔥🔥🔥 Can't believe the size of these 5 for autos! Epic! Did some defoilation on the bottom of plants removed anything not getting light Lowered humidity to 45-48% for the late flowering! 24-26 degrees day 19 degrees night Smell is picking up big time! I let them completley dry out until I watered again. They all seem to be smashing it! buzzing with results so far!! not long now!!!! 👊👽👊