Likes
46
Share
Hello growers and tokers! 👋 👩‍🌾 🧑‍🌾.🔥💨 It's my first harvest on this community and I'm loving it. Everyone always ready to help each other and have great feedback. Tracking my grow on here has made it way easier. There were times that I misplaced notes or forgot what I did or when with a certain strain and all I had to do was come on here and check it. Also motivated me take more pictures and do more logs. All out great site. Don't know how I haven't found it earlier. HIGHLY recommend for all growers. The grow cycle went pretty smooth. She's easy to grow and flowers early so you can't do much training. That being said it's great for beginners. 👌 Had no problems with pests on these, while on the other plants (none cannabis) in the balcony I had issues with spider mites. They grew better than expected given the few hours of direct sunlight they received. Results were good, I was expecting 10-15 grams per plant and ended up with a tad bit more. Drying went a bit fast because there were few buds. I probably could have took it down a few degrees as well.. my fault on that part. They dried in 4 days, they've been curing for 10 days. I normally test them after 15 days but they smelled so good I had to try them. Smell: Lovely earthy, woody, slightly like diesel. Quite pungent for being autos. Taste: Just as it smells.. leaving a nice after taste of diesel. Touch: Very sticky, dense buds. They break down finely in the grinder. Cleaned the grinder before testing and after 4 joints ( 2 grams or so) I already have a good amount of kief collected in the bottom. (Check photo) Might grow this one again just to make some bubble hash. The high is awesome nice uplifting, long lasting energetic but without a heavy euphoric rush. Reminds me of a smooth haze high, although if you smoke a lot even being an experienced smoker, she'll get to you. Only down side is dry mouth, very dry mouth! Have some water on hand because your mouth will transform into a desert. 😂 Great strain to kick start the day. Beginner smokers take it easy with this one. She hits hard! 👊
Likes
57
Share
@Roberts
Follow
Pablo Escobar is growing well. She had the light changed for flowering 4 days ago. She also had a solution change 2 days ago. She was defoliated some today as well. Everything is looking good at the moment. Thank you Spider Farmer, and Divine Seeds. 🤜🏻🤛🏻🌱🌱🌱👍🏻 Thank you grow diaries community for the 👇likes👇, follows, comments, and subscriptions on my YouTube channel👇. ❄️🌱🍻 Happy Growing 🌱🌱🌱 https://youtube.com/channel/UCAhN7yRzWLpcaRHhMIQ7X4g
Likes
17
Share
Likes
71
Share
Hello Growers 👋 👋 👋 At last I am doing an update 😇 It's Day 49th big changes occur in my tent. She is a cracker 😇 😇 😇 after that small L.S.T. she released her potential. She is so so so huge, all that tops you can see are a side branches 🤯 🤯 The Gelato growing very healthy and very fast, this is one of my best looking plant so far. I'm very happy to see her in that condition, it's looks like the harvest could be very big 😀 😎 😀 Please have a proper afternoon rest 🙏 You Lovely Girls Growers 😇 🌻
Likes
2
Share
WEEK 4 SETUP - ROOT ZONES Optimizing cannabis performance requires balancing a strict temperature gradient between a cool root zone (68°F–72°F) to maximize dissolved oxygen and active nutrient transport, and a warm canopy (77°F–95°F) to accelerate photosynthetic enzyme activity and electron transport rates. There is a critical anatomical temperature gradient required for optimal cannabis metabolism: The Root Zone (68°F–72°F): Must be kept cool to maximize dissolved oxygen, preventing root rot (Pythium) and ensuring active transport ATP powers root elongation. The Metabolic Sweet Spot (77°F–95°F): The primary Electron Transport Chain (ETC) enzymes and ATP synthase complexes in the foliage require these warmer temperatures to maximize molecular collisions, accelerating respiration and carbon fixation. The Destruction Threshold (104°F): Enzymes and lipid membranes denature, causing structural metabolic collapse. Active transpiration constantly pulls dissolved O2 down through the top of the substrate like a piston. At night, the top-down pump completely stops. When transpiration shuts down after dark, the root zone can quickly become stagnant and oxygen-depleted because the mechanical "pump" is off, while the roots still need to breathe. Having a hole in the middle of the 100 gallon, in which all the air intake in an indoor grow tent comes up through the middle of the pot rather than open side panels, and having tent exhaust connected to RH allows cellular respiration to enact the exhaust, which creates a negative pressure differential that will act as a pump at night similar to daytime, but with a different mechanism. By routing your intake exclusively through a central hole in the pot and linking the exhaust to a Relative Humidity (RH) controller, you are effectively replacing the daytime transpiration-driven pull with a nighttime vapor-driven physical pull. Because the side intake vents are sealed, the tent is forced to draw its replacement air directly up through the center of your massive pot. This actively pulls stagnant, CO2-heavy air out of the root zone and replaces it with fresh, oxygenated room air. UVC 264nm duct sealed with HEPA filters to prevent contamination of pathogens. Constant airflow of 0.2m/s underside of the elevated pot to prevent potential runoff stagnation. Polystyrene insulation to prevent core desiccation, HVAC climate-matched intake, inline UVC/HEPA filtration, and constant underside air velocity are successfully engineered around every major failure point. Because cellular respiration spikes RH in waves, ensure your exhaust controller has a tight deadband (e.g., +/- 2-4% RH). This prevents the fan from "hunting" (short-cycling on and off too rapidly), which would cause erratic pressure shifts in the root zone. Using large-sized Hydroton (expanded clay) pebbles fill a 12-to-14-inch diameter middle cavity in the pot solves the air channeling problem entirely. By replacing a dense substrate core with a highly porous, structural aggregate, it creates a dedicated internal air plenum. This ensures that the negative pressure differential acts uniformly across the entire vertical column of the root zone. Often referred to as a sub-surface aeration plenum or negative-pressure root system. By using negative pressure to pull or push conditioned air through a Hydroton (expanded clay pebble) plenum, this setup optimizes the root zone microclimate while preventing the typical gas stratification found in traditional containers. The 12-to-14-inch Hydroton layer acts as a high-porosity distribution vault. Because Hydroton has massive interstitial spacing, air can move through it with minimal resistance before diffusing into the denser substrate above. Instead of air channeling up a single path, the system forces the conditioned air to spread outward and upward evenly across the entire radius of the root mass. Roots actively consume Oxygen and respire Carbon Dioxide (CO₂). In standard pots, heavy CO₂ and excess Nitrogen can settle at the bottom, creating an anaerobic "dead zone." This negative pressure actively pulls those heavy gases out, replacing them with oxygen-rich, HVAC-conditioned air. Roots that penetrate the polystyrene/mesh barrier into the Hydroton core will experience incredible growth due to the hyper-oxygenated environment. However, because of the high nighttime airflow, the surfaces of the Hydroton will dry rapidly after irrigation. This will create a localized, self-regulating air-pruning zone, forcing the plant to explode with dense, lateral feeder-root branching just outside the core. Turns one's massive pot into a bi-directional, lung-like matrix. Equipped to destroy all limits set before it with nearly zero points of failure. With these safeguards implemented, the root zone environment achieves an unprecedented level of equilibrium. The plant drives the system. High transpiration creates a powerful top-down pull, dragging oxygenated moisture through the upper profile. The HVAC and HEPA/UVC intake runs passively or under low static pressure to maintain ideal ambient baselines. Transpiration ceases(Photosynthesis), and metabolic cellular respiration triggers a spike in relative humidity. The RH controller instantly fires the exhaust fan. The negative pressure vacuum instantly engages the clean, conditioned cohesive air column. Fresh air sweeps through the sealed duct on the underside of the buffer zone(pot), enters the 12-to-14-inch Hydroton plenum, and diffuses radially outward through the HVAC-controlled substrate. Stagnant CO₂ and nitrogen are actively evacuated. This setup prevents root rot, boosts oxygen levels at the root zone, and accelerates plant growth by ensuring the root system always breathes fresh air. Polystyrene keeps the core from drying out prematurely, the physical barrier keeps the media from migrating into the plenum, and the climate-controlled intake ensures the root zone never drops below its metabolic sweet spot. In standard growing systems, a root zone of this massive scale always runs into a diminishing return curve: the larger the pot, the easier it is to create cold, stagnant, anaerobic dead zones in the deep interior. This design completely smashes that ceiling. By turning the absolute center of the mass into the cleanest, highest-flowing, most oxygen-rich zone in the entire garden, you allow the root system to expand exponentially without ever hitting a wall. One is giving the plant the ultimate foundation to maximize its genetic potential, pushing growth rates, nutrient uptake, and overall vitality to their absolute limits. Also allows intake while catching all CO2 generation in the bottom half of the tent, kicking it up into the canopy every morning, even all around with 360 distribution, zero dead spots. Sub-surface aeration and magneto-electroculture matrix: a highly sophisticated, closed-loop engineering framework that perfectly bridges plant physiology with fluid dynamics and electromagnetic physics. By turning a traditional container into a bi-directional pneumatic lung, the design successfully bypasses the biological stagnation limits of massive root zones while leveraging micro-Lorentz forces to enhance nutrient mobility. Integrated a massive copper rod with an iron core (an electromagnet core) directly down the central axis of the Hydroton plenum—and driving a magnetoelectric field at the base using a neodymium magnet—shifts this setup from a basic galvanic circuit to a specialized magneto-electroculture matrix. Running the earth battery's DC current through a highly conductive copper casing insulated around a ferromagnetic iron core, transforming the central air column into an inductive broadcast tower for the rhizosphere. Just big enough to fill the massive riotzones but not leave the 4x4 tent. The physics and structural safety of this addition alter the system's dynamics in a couple of ways. Copper is an excellent electrical conductor but is non-magnetic. wrapped the high-permeability iron core inside that copper column, you focus and amplify any magnetic flux lines generated by the circulating micro-currents. ⚠️ Extreme Handling Hazards ⚠️ 38 mm OD x 19 mm ID x 6 mm N52. ⚠️ Extreme Handling Hazards ⚠️ ⚠️Keep it well away from pacemakers, credit cards, mechanical watches, and sensitive magnetic sensors.⚠️ There is a permanent neodymium magnet at the base of this core inducing an electrical current this creates a localized electromagnetic actuator. Because it sits at the bottom of the plenum (where your HEPA/UVC filtered intake air enters), the air moving up the column passes through a dense, structured magnetic gradient. As HVAC-conditioned water droplets and dissolved nutrient ions flow outward from the Hydroton plenum into the biochar, they cut perpendicularly through this magnetic field. This exerts a micro-Lorentz force on the free ions, altering their kinetic trajectories and potentially boosting ion mobility through the substrate's high-impedance boundaries. The central rod is sealed in a non-conductive jacket below the soil to allow the magnetic field to pass through while physically isolating the raw metal from moisture. Iron cores radically increase magnetic field strength, but they also introduce electrical resistance. If the current from the earth battery hits a bottleneck in the central rod, that energy transforms into heat. Given the root zone has a strict oxy threshold above 75F you must use a digital multimeter to verify that the central rod is not acting as a heating element. Copper is highly toxic to plant roots in elevated atomic concentrations. Because the central plenum experiences a massive, nightly rush of high-humidity air driven by the pneumatic exhaust lung, an unsealed copper rod will oxidize rapidly. This creates copper carbonate or copper sulfate runoff that will toxicify the hydroton pruning zone. Luckily we don't top water. Roots exhibit magnetotropism (growth responses to magnetic alignment). A constant, hyper-intense magnetic field can distort root elongation or cause root tips to prematurely deviate from their lateral path toward the biochar. Ensure input voltage stays strictly in the micro-current range to keep the magnetic flux lines subtle and non-disruptive. The permanent magnetic field has a profound, measurable effect on the surrounding rhizosphere. Placed right in the middle of a massive 100-gallon pot, the 38 mm neodymium magnet acts as a powerful bio-magnetic anchor. Because the magnet is completely sealed and safe from corrosion, its magnetic lines of force will constantly radiate into the soil matrix. In plant biology and soil science, this triggers several notable physical and biological shifts. Water molecules are diamagnetic (weakly repelled by magnetic fields). When water moves through the soil near the magnet—whether from watering or root suction—the strong permanent magnetic field temporarily loosens the hydrogen bonds between water clusters. It breaks larger water groupings into smaller, highly uniform clusters. This "magnetized water" moves through soil capillaries more fluidly, lowering surface tension and allowing the roots and surrounding microbes to absorb moisture and dissolved ions much more efficiently. The field stimulates soil enzymes like phosphatase, which unlocks bound phosphorus in the soil and turns it into a bio-available format for the plant. Many beneficial Plant Growth-Promoting Rhizobacteria (PGPR), including nitrogen-fixing strains, are magnetically sensitive and show increased activity and modular clustering under a magnetic field. The field strengthens the communication networks among soil microbes, which actively boosts the plant's natural tolerance to environmental stressors like salt or drought. Roots exhibit a subtle trait known as magnetotropism. Plant cells use internal electrical gradients to guide growth and transport nutrients. The permanent magnetic field alters the transport kinetics across cell membranes, influencing auxin (growth hormone) distribution. As roots grow into the middle zone of the 100-gallon pot, they will likely develop denser branch networks and thicker root hairs to maximize surface area contact. Magnetic field strength drops off drastically with distance. A 38 mm neodymium magnet exerts a massive effect on the soil within a 10–20 cm (4–8 inch) radius around it. In the 100-gallon pot, it will not drastically affect the outer edges of the soil, making it a perfectly sized "core zone". The roots must grow relatively close to the center to interact with the high-flux zone of the field. Once they do, though, oh my days! explosion.
Likes
12
Share
Forgot to upload week 7. After res change, next day that polka dot pattern came on top leaf. Cut off with a bud (another location) that dried up prematurely. The 650 nutes got sucked up a lil bit compared to these sativas water intake. Every day 1-1.5 gallons. That in an 9 hr spand when im at work. Struggling with rh bc of blizzard than warm, then rain, then cold, then repeat. Put a dehumidifier that does my whole basement in the room to suck out the moisture so the new air intake can pump dryer air
Likes
1
Share
@Wiffz_CBD
Follow
Grow dots added at beginning of grow. I’d say it’s working great. And it’s simple. Cal-Mag added in reservoir 1tsp/1gal Recharge .5tsp/2.5gal -fed 1L
Likes
2
Share
Hy Growmies, The stretch is over, so I switched to CANNA Aqua Flores. Almost screwed up since I Had a light leak through some Styropor and had some white slime on the roots under the leak. Removed the water and sprayed them directly with some 3% hydrogen peroxide. Worked great now we are on track again.
Likes
28
Share
It's the 4th week of Flower!! I've gotta say, counting weeks is tough and I always get it mixed up. 0-7 days is 1 week. So this is week 4, days 21-28. I do some reason feel like the 28th day should be the start of week 4 but it doesn't work that way...idk sorry bout the rant! This week I wont do a day by day as nothing has happened per those days. Except for Thursday. Day 27 of flower. Every Thursday we water in the Teas and recharge. I also, lollipopped her this week and removed some of the larger fan leaves. CMOG is the heaviest plant as it is and some great spacing between buds ensure hood light penetration. She is getting super stinky and frosty too!! Cannot wait for 1 more week for her to really pop!!
Likes
307
Share
@Ju_Bps
Follow
Hello growmies 👩‍🌾👨‍🌾🌲🌲, 👋 Let's go for the flowering, stretch Started, hope can stay under control, we can start to see the first pistils, Plant look happy. Weather start to be really cold, and worst next weeks, we'll see how turning. 💪 Keep Working on the canope, removing leaves and under buds site. 🕑 Now 12/1 💧 Give water each 2/3 day And vaporise plant with water + Plagron Roots (1ml/l) 1.5 l Water + Roots + Bloom + Zym + Sugar Royal (1 + 3 + 1 + 1 ml/l) PH @6 💡Mars Hydro - FC 3000 50% 43 cm. Mars Hydro Fan kit Setting 5 Have a good week and see you next week 👋 Thanks community for follow, likes, comments, always a pleasure 👩‍🌾👨‍🌾❤️🌲 Mars Hydro - Smart FC3000 300W Samsung LM301B LED Grow Light💡💡 https://www.mars-hydro.com/fc-3000-samsung-lm301b-led-grow-light Mars Hydro - 6 Inch Inline Fan And Carbon Filter Combo With Thermostat Controller 💨💨 https://www.mars-hydro.com/6-inch-inline-duct-fan-and-carbon-filter-combo-with-thermostat-controller Anesia Seeds - High Mars 36% THC🌲🌲 https://anesiaseeds.com/product/high-mars/
Likes
7
Share
@Cargic
Follow
I haven’t been really keeping up with her as much as I should since holidays were around. I haven’t been raising my light as I should which didn’t do a whole lot. It definitely lightened her up but that also could be from it being in flower. Everything’s been going very good I couldn’t ask for a better grow!!
Likes
2
Share
@TowersD
Follow
Starting week 5 of flower. Plants are starting to bulk up! Nanaz x BBC smells fruitty and gas, Headband #2 smell citrusy and Headband #1 smell les citrusy and more like grass
Processing
Likes
23
Share
Another week down few more to go can't wait!! First ever attempt of growing my own so really impatient to see the final results now and get to the finish line, that said all has went well upto now other than the size they reached haha, really started putting on weight now it seems and they smell lovely, excited to see the buds fatten and progress over these last few weeks up until harvest now, started 5 liberty haze also they are just coming upto 3 weeks now so check that diary out to, any comments info tips for the final stages appreciated
Likes
25
Share
@Rob691
Follow
D-104 : Last week, I noticed a problem related to the calcium OR to the Ph. I didn't know if it was a deficiency or an excess. So I tried to just wetered girls with the right Ph and A bit more of CalMag 0.8 > 1.2/L. We'll see this week if It was the good choice. fingers corssed !
Likes
6
Share
@Arcadium
Follow
Had a heat wave blow through, 32c days, plants blasted all day. Growing much quicker, easy week, didn't do much, may start scrog net next week. Final topping has recovered, even canopy forming, no issues at all. Weekly lost coast spray and 2hr 15min of drip was it for this week, top dress feeding next week.
Likes
32
Share
Info : Unfortunately, I had to find out that my account is used for fake pages in social media. I am only active here on growdiaries. I am not on facebook instagram twitter etc All accounts except this one are fake. Flowering day 56 since time change to 12/12 h. Hi guys :-) The buds are slowly but surely coming to an end :-). The next 10-14 days will be harvested. It was poured 3 times this week. One of them with GHSC enhancer. Everything was cleaned and checked. Stay healthy 🙏🏻 You can buy this Strain at : www.Zamnesia.com Type: Runtz ☝️🏼 Genetics: Zkittlez x Gelato 👍 Vega lamp: 2 x Todogrow Led Quantum Board 100 W 💡 Bloom Lamp : 2 x Todogrow Led Cxb 3590 COB 3500 K 205 W 💡💡☝️🏼 Soil : Bio Bizz Coco ☝️🏼 Nutrients : Green House Seeds Company Powder Feeding Bio ☝️🏼🌱 Water: Osmosis water mixed with normal water (24 hours stale that the chlorine evaporates) to 0.2 EC. Add Cal / Mag to 0.4 Ec Ph with Organic Ph - to 5.8
Likes
13
Share
apenas 1 das que estavam na tela de SCROG conseguiu sustentar até essa semana mesmo com problema de PH do solo, as outras 3 tive que colher na semana passada, a descoloração das folhas já começando a indicar que o fim está próximo, pouquíssimos tricomas ambar, cheiro maravilhoso!