Recommended
Likes
Comments
Share
Looking good lowering temps to keep my terps from burning off remember once you smell it their gone forever lol! I did run through a few little problems you can see rip burn and some stretching one was a experiment and one was my own fault. As of right know tho I’m very happy for this harvest!
Processing
Likes
51
Share
12/15: Some plants are taking too long to transition and stretching beyond my space constraints, so I dialed the photoperiod back to 12/12. 12/16: Fed today and rotated edge plants. Added another 150w of 3000k below the canopy. Sucrose Overdose and Muscadine Wines are still stretching...raised lights again. 12/17: Worked on ventilation...no A/C necessary now, as I'm using another AC Infinity 6" fan to intake outdoor air into the closet whenever temps reach 75f..and it's been cold as hell outside.👍 The final trick will be to replace the 6" exhaust fan with an 8" so as to be able to fully exchange the closet air faster ...but that's gonna have to wait til next season. 12/18: Supercropped a Muscie... again... now she's doing the "letter 'S' thang. I'll force the curves tighter over the new few days if she keeps stretching.
Likes
15
Share
End of week 2, been a bit inconsistent this week with the pictures, but overall it looks good !
Likes
10
Share
Hi Dear Friends, 👨‍🌾 👩‍🌾 Plants showed some deficiencies, but we are recovering it. I prefer to have deficiencies instead excesses.. Maybe It was better if I started a week ago to give Top Veg. It is the biggest of the cycle and it is really fast. I notice a HUGE difference compared to other plants growed under the 480w quantum board. The Kush mintz Fast is under the the XS2000 by ViparSpectra and it is bigger and stronger compared to other plants. Small distance between internodes and stems hard like rocks. This lamp is really a beast, can't wait to try the new models!! ✅ VEGETATIVE week #7 (LAST WEEK) 30/12 SWITCH 12/12H 📅this week goes from 26/12 to 01/01.📅 💡💡💡Viparspectra XS2000 is working at 50% power. 💉🔍Fertilization schedule:🔍💉 26/12 3ml/lt TOP VEG 30/12 TOP MASS 0.2ml/L + 2.2 ml/L TOP VEG 31/12 SENSI CAL MAG EXTRA 2ml/L foliar spray WE ARE BACK!!! We are back after a little pause. We take a break because we were too busy to post high quality diaries. In the last diaries we tried to post as good as possible and we have to publish about 6 or 8 diaries (in addition to these that we will publish shortly). We opened also an educational Instagram page, we growed a lot in a short amount of time BUT, Instagram suspended our account and we lost all our posts, I was so sad and disappointed... a lot of work lost in a night.... In this diary you will see our journey with Kush Mintz Fast by Original Sensible 🤩, sit down and enjoy the show! We are growing in a 15L Smart Pot with Light Mix soil by BioBizz under the AWESOME XS2000 by Viparspectra 🤩 DATA SHEET: Bubba Kush , Animal Mints, Secret Hybrid Genetics: mostly Indica Yield: 650g/m² indoor flowering time: 50/55 days THC: 25% Aroma: cookie mint Effect: happy relaxed 💸💸💸💸💸 Here you can buy seeds of this top shelf strain: https://originalsensible.com/original-sensible-seeds-kush-mintz-fast~21711 _______________________________________________________________________ 🔧💡OUR SET UP💡🔧 ✔️ 💲💲💲VIPARSPECTRA 🚀🚀🚀🌕🌕 ViparSpectra®️ XS2000 240W Infrared Full Spectrum LED Grow Light: Excellent ratio between wattage and ppfd, excellent light penetraton, perfect light spectrum (it also has IR 🤩) and it has the best build quality on the market. Until now, built quality is really awesome. You can touch that quality. Materials are really strong, excellent driver and the best leds on the market. Heat dissipation is perfect, the lamp is never too hot and it has a passive dissipator so you will have zero noise. It also has IP65 certification. I like that this lamp is bigger than others, so the 240w of power are well distribuited on the space. Viparspectra has an awesome customer service, and shipping was creazy fast! This awesome brand also offers 3 years warranty. This lamp has no rivals. A special thanks to Emily of Viparspectra ❤️❤️❤️❤️ HERE YOU CAN BUY THIS PROFESSIONAL LIGHT: https://www.viparspectra.com/products/xs-series-xs2000 or https://amzn.to/3dyUoJl and here you can buy other awesome stuff: https://www.viparspectra.com ✔️ 💲💲💲MARSHYDRO 🚀🚀🚀🌕🌕 📦120X120 GROW TENT: an awesome box, easy and fast to assembly. Made by strong materials, solid zips and it is totally lightproof. The position of holes is optimal and the two lateral windows will make easier the work inside the box. There is also a double end, so you are 100% sure that dirt or liquids will not spill out. You can find it here: https://www.mars-hydro.com/grow-tent/buy-mars-hydro-grow-tent-48x48x80-1680d-4-x-4-size-keeps-all-light-in-top-quality-1680d-canvas-is-tear-proof-and-double-stitched-light-blocking-fast-installation-for-sale 💡TS 600 FULL SPECTRUM 100W LED GROW LIGHT : with this light you will achieve excellent buds, you will not need anything more. This lamp replace a 150w HPS lamp, but, with this Led Light you will smoke bigger, harder and tastier buds because Led have a complete spectrum and a powerful light penetration, so your plants will work as much as possible to make you happy. Psssssss it it extremely cheap and it is only 100w, your bills will never be too high, YOU HAVE NO EXCUSES!! Here if you want this little beast: https://www.mars-hydro.com/led-grow-light/mars-ts-series-led-grow-light/mars-tsw-600-led-full-spectrum-hydroponic-led-grow-light Thank you Eleen of Marshydro❤️❤️❤️❤️ 💣Quantum board - 480w - 4x120w Boards by Zhoangshan Koray Opto-Electronic Ltd. Samsung LM301B 288 led/board 3000K 0dB noise +24led/board led Osram 660nm Efficiency 2.6 umol/J 220 lm/w Driver: Meanwell HLG-480H-36B 💣Quantum board - 240w - 2x120w Boards by Shenzen Yuanhui Led Ltd. Samsung LM301H 504 led 3500K 0dB noise +24led/board led Osram 660nm Efficiency 2.7 umol/J 220 lm/w Driver: Meanwell HLG-240H-48B -ESTRACTION FAN: Blauberg 125 Turbo Pro Series Maximum air flow: 430-560 m³ / h 50W 32-44 dBA -FANS: A)OSCILLATING FAN D.15cm 2 speeds 20w B) COMPUTER FAN Sunon DP200A – 230V 20w (Strong, reliable and quiet) C)Cornawall Electronics Multifan Turbo, three speeds, can be used both on support surfaces and mounted on the wall. High capacity, about 740 m3 / h. High silence and reliability. 💊💉💊FEEDINGS: We used BioBizz light Mix TOP CROP: -DEEPER UNDERGROUND: to stimulate roots system -TOP VEG: for a excellent growth in the vegetative phase -GREEN EXPLOSION: to promote creation of bud sites and to allow a faster growth -MICRO VITA: bacterias for equilibrate the soil and to make the plant healty -BIG ONE: to stimulate bud sites and to stimulate resin production -TOP BLOOM: to achieve excellent big and hard buds -TOP CANDY: to feed the buds with molasses for a tastier smoke and to gain weight -TOP BUD: to enlarge buds and to gain weight PLAGRON: PK 13-14 to have big and hard buds and to feed plants with lower effort ADVANCED NUTRIENTS: Sensi Cal-Mag Extra-> for cal mag deficiency GROTEK: CAL MAG for cal mag deficiency HESI: PowerZyme to clean and balance the soil. It feeds the plant cleaning the soil. GHE: - Final Part (ex Ripen) accelerate the final flowering phase, dissolves minerals in excess - Flash Clean to flush the plant and to be sure that all excesses are out from plant and pot These two products improve A LOT the smoke of our babies -PURPINATOR to stimulate flavonoids and to have a better taste and smell. ____________________________________________________________________________________________ 🙏❤️ THANK YOU FOR BEING HERE ❤️🙏 Please leave a comment with your opinions, it is very important to us to have a comparison. If you like our job, tap the weed button and follow us. It will be really appreciated.🙏 We want to thank again everyone that help us in our project. You support us to support our dream. ❤️ SPREAD THE LOVE OF THIS PLANT ALL AROUND THE WORLD 🌿Thank you again🌿 ❤️Sweet hugs❤️ 👨‍🌾CHILLING_RACOONS👩‍🌾
Likes
12
Share
@Naujas
Follow
The girl's upper leaves look terrible :( I didn't manage to give her more potassium in time :( Well, the flowers bloomed really well, they are not small, and there is definitely a lot of sugar on them :) the smell is also amazing :) apart from the upper leaves, everything looks pretty good :) when I cut her, her image will change :) I think she has max 2 weeks left ;)
Likes
11
Share
@MG2009
Follow
06/17/2020 I'am not sure how she will produce,but the smell is intoxicating! Wow that's all I can say. Better than any gg I've smelled thank you Fast Buds! In fact I love it so much I have decided to selectively pollinate some buds with Red Sky male , that should make for some freaky flavor combos! I think she is stretching and filling out she looks happy! I do have powdery mildew on the stem need to clean it up oh yeah did I tell you I love the smell! Lol
Likes
64
Share
@Prof_Weed
Follow
Alles funktioniert einwandfrei, die Buds werden fetter und die Pflanze riecht sehr gut.. Schätze mal 3 Wochen noch..
Likes
223
Share
💩Holy Crap We Are Back At It And Loving It💩 👉WE R SO CLOSE NOW👈 Growmies we are at DAY 70 and there all just killing💀it👌 The Gorilla Punch Is Amazing 👏 But so is the OG 👉We are in full flowering mode for the👈 OG 👍 GP 👍 the AF was the hold out but shes finally flowering👈 So Shit , I gave them just a tad to much nutes at the start feeding 👈 But I have since fixed it So I'm still doing some low stress training 🙃 and some defolation 😳 Lights being readjusted and chart updated .........👍rain water to be used entire growth👈 👉I used NutriNPK for nutrients for my grows and welcome anyone to give them a try .👈 👉 www.nutrinpk.com 👈 NutriNPK Cal MAG 14-0-14 NutriNPK Grow 28-14-14 NutriNPK Bloom 8-20-30 NutriNPK Bloom Booster 0-52-34 I GOT MULTIPLE DIARIES ON THE GO 😱 please check them out 😎 👉THANKS FOR TAKING THE TIME TO GO OVER MY DIARIES 👈
Likes
2
Share
@Bluemels
Follow
Tag 53: Ab heute gebe ich kein Dünger mehr, in 2 Wochen will ich ernten.
Processing
Likes
Comments
Share
@MG2009
Follow
08/13/2019 Another rainy day. Recovering from topping and,fimming. Looking good for start of flower, soon. 08/18/2019 Did a little training.
Likes
2
Share
Just a nasty little runt that couldn’t take the heat and crazy weather! Had this happen twice before with autos specifically. Not going to waste any more time! Oh well! On to the next! ✌️🏻💚
Likes
371
Share
D64. We're at the start of the fourth week of flower, and today was a busy day. First, I had to remove the old lights before swapping in the light from my auto tent. All while trying to avoid trashing the plants in the way too full tent. Not an easy task. The entire mission, with changing the light in the auto tent as well, took a couple of hours. I wish I could keep the Greenception lights in the tent as they're high-quality lights, but the Kingbrite has a much lower profile and thus takes up much less space. Space that I desperately need considering how insanely much these girls stretched. One of the tops on the second girl has unfortunately already been bunt by being too close to the light, and I'm sure I will run into light bleaching and probably foxtailing as the grow progress, but I hope I will be able to pull it off with the Kingbrite light. I also added some wire support to the branches that I super-cropped, as they looked somewhat sad after all the abuse to the canopy while swapping the lights. ------------------------------ D66. It looks like the girls have FINALLY stopped stretching. Phew! Yesterday, I gave each girl 2.5 liters of water @ pH 6.2 with humic acid and EM-1. Today, the green lacewing larvae (Chrysoperla Carnea) arrived, and I dispersed them in the tent to deal with the thrips. ------------------------------ D68. All is well in the tent, but now when the thrips are (hopefully) under control, it's time to address the VPD. It has gotten seriously out of wack due to dropping temps, plus I increased the humidity to make the environment more inhospitable for the thrips. The temps were low due to the light change as the new one is running a lot cooler, but the temps have also dropped outside. The heating in the lungroom has been off until now, so I turned that on and lowered the humidity threshold on my exhaust fan. Finally, I put my small humidifier in the tent, generating extra heat and decreasing the humidity. So far, the VPD has increased from a terrible 0.4-0.5 to an acceptable 0.9, and I'm hoping it will increase further as the ambient RH drops as we move into winter. ------------------------------ D70. We're at the end of the fourth week of flower, and all is well in the tent. The VPD has gone up to 1.0, which is a nice improvement to what it was only a couple of days ago. I haven't scouted yet for thrips, but I will give the lacewings a couple of days to do their thing and then look closer. However, I went to WAR against the spider mites we have in our ornamental plants in the apartment. I sprayed all plants with my homemade pesticide (capsaicin, alcohol, horticultural soap.) since I had it at hand. If that fails to knock the spider mites back, I'll bring out the neem oil instead. The infestations aren't bad (yet), but it would suck to get mites into my tents, so better to be proactive. ------------------------------
Likes
168
Share
📆 Week 7, 17-23 June 2024 17-23 June - Observed and let the plant grow. 📑 Pablo is about out of her pre-flower stretch now and into the first week of true flower. Her leaves are big and lush which makes shading a real challenge. I’ll have to defoliate soon to keep her growing evenly. 🍶 20 June nutrient solution changed 🍽️ 20 June feeding schedule updated 💧 Using reverse osmosis water with EC/TDS at 0 🐉 Nutrient solution EC 2.6 at 74 degrees F 🔆 Light power at 80%, DLI 40 canopy coverage at 12hrs 😤 Using PYPABL, Air Pump, 400GPH That is it for this week. Thanks for the look, read and stopping by.
Likes
12
Share
@yd_grows
Follow
Planta crescendo absurdamente rápido. Fiquei 3 dias sem olhar após regar e tinha uma flor encostando na luz!! Absurdo. Muitos buds aparecendo. Folhagem parece densa demais. Devo retirar algumas folhas na semana seguinte.
Likes
45
Share
~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_ ❤️💡🌱😽💨 We're back from vacation!! These did great on autopilot, of the 6 plants, these 2 are definitely my favorite.. a simple 4way LST when all tops come in level makes me happy 😻. they're still a little too dark/overfed so we're going super light for a while.. We raised the Solux350 a few inches as well, they're stretching fast... all other plants were showing early signs of cal-mag def so we adjusted strengths for everyone.. We have the Solux350 at 75% power, we'll keep it here until their flowering stretch is over and finish out at 100%...I'm really curious to see if resin production using 2835pro/Osram combo is comparable to what 301b/Osram does.. We have another 300watt using these diodes and that tent is a frost factory lmao..not too much else to report, it was nice not returning home to dead plants lol..thanks as always for dropping by and happy harvests everyone!! 🤘😼❤️🌱 ⚡Hortibloom/Solux 350⚡ Specifications ⚙️: Diodes: Samsung LM281 Pro / Osram DR (1,440 total)💡 Driver: Inventronics 350 watt🔌 PPF: 1015 μmol/s ☢️ PPE: 2.9 µmol/j 〰️〰️ Lifespan: 50k+ hrs ⌛ Weight: 14.3lbs lbs (6.5kg) Veg Coverage: 5 x 5 ft 🌱 Flowering Coverage: 4 x 4 ft 🌼 -Uses an aluminum heatsink (no fan), quiet while operating 👂⬇️ -IP65 waterproof ratings, tolerant to high humidity grow environments 💦 -May be daisy-chained via RJ14 and managed from a single controller 💡~💡~💡~💡~💡 🌎 https://hortibloom.com/products/solux-350-led-grow-light ~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_~_
Likes
6
Share
Hello everyone, Been busy this week working around the house so not much I can say. Heres a little video of there growing... See you guys next week
Likes
24
Share
@3lementa1
Follow
I had been feeding with a diluted solution and now after flushing with water last week I'm moving up to full strength. The pistils of the plants on the ends seem healthier. The smaller plants in the middle seem a little more scraggly. I'm making full use of the SCROG net. I also raised the light an inch or so and put it back to 100% from 75%. I'm going to see if I can keep it closer to 100 if I can balance the intake air temp. Some of the leaves are damaged. I have a feeling it's from the cold nighttime air coming in the intake. I'm going to keep the intake fan off at night while it's this cold and damp outside. Hopefully not too much smell escapes. Maybe I should seal it at night. Getting sticky now!