Not much going on yet. Added some 3d printed supports to make sure they don't start flopping over. Not sure if it's the strain, or my idiocy, but these bastards are soooo leggy. Grr. Watering daily to 15% runoff with MegaCrop 2 part in RO at 0.6EC and 5.6pH. Found Mega Crop gives very stable pH on the right range without any pH up or down needed. Took one day off (3/18) watering to water with Silica Boost at 6ml/gal concentration pHed to 5.4. PPFD 300 at canopy for DLI of 20. PPFD was about 20 for first week while I was prepping and sanitizing the grow room, which might explain the leggyness. If they don't look better after topping, I might pull them and try a different strain. 3/20 - this grow is inspired by the techniques of Bruce Bugbee (PPFD, nutrition, EC monitoring, substrate, environment, etc) and the concept of VPD control, both of which served me very well in the past. The grow room has dual PID controls in my PLC regulating the temperature and humidity to lock in the VPD based on plant age. In later veg and flower, I had CO2 injection on a PID, but that ultimately failed because I couldn't get the humidity down as it got huge. Had too many vent cycles. This year, hope to source or kludge an in-line dehumidifier so I can keep the sealed chamber where it needs to be without wasting CO2. 3/22 no more vertical growth, thank god, leaves and roots are slowly catching up. Patience. EC to 0.7

trichome development is coming along however I am worried that they might not make it until harvest. I will be starting 2 photoperiods along side 1 other auto on my next grow with suitable nutrients for my medium.

Noticed some yellowing on sour kush a on Monday I do check ph and ppm overall smells nice critical purple finally taking off sticky buds on b and c

DID SOME MAJOR DEFOLIATION TO SLOW THE GROWTH ABIT. IM GOING TO PUT THE 15 PHOTOPERIODS IN THE 8X8 TENT TO FLOWER BUT I NEED TO HARVEST THE AUTOFLOWERS FIRST. FOR EVERYTHING MARS HYDRO VISIT: www.mars-hydro.com www.marshydroled.ca PROMO CODE: rocknroll VISIT THE ALIEXPRESS STORE: @marshydro_aliexpress Instagram: @marshydropenny Thanks for taking the time to read and check out my diary🤜🤛 TS3000 FEATURES: WIDEBAND SUNLIGHT FULL SPECTRUM LED GROW, Infinite close to natural sun light, suit for all plants whole stages indoor growing, rapid plant response from seed to flower, achieve maximum quality and quantity, much better than traditional HPS grow systems. HIGH REFLECTIVE & NOISE FREE-Fanless LIGHT BOARDS design will make your growing life easy and quiet, quickly heat dispersing material aluminum reducing light lost to aisles and walls, increase the light intensity up to 20%, allowing your plants receive more energy and without burning your plants for maximum headroom. HIGH EFFICIENCY ENERGY SAVING PLANT LIGHT, high-power NEW LED grow, Compares to traditional 3000 watt HPS lamp and other brand led grow light while only 450 watts true output with 1016 LEDs, more scientifically and energy-efficient! Perfect for 5' x 5' veg stage, 4' x 4' bloom stage, higher intensity in a MARS HYDRO grow tent, reflective area, or by crossing over using multiple TS3000. BOOM YIELD LARGE GROW LIGHT, NEWEST SMD LED technology provide highest PAR/LUMEN output(1095.6umol/), makes you get 30% higher yield compare OLD led lights, can get max yield at 2.5g/watt, less pay but get more yield, bring a amazing grow trip to any home grower as it beams huge amounts of light energy to plants below. COMMERCIAL LED GROW LIGHT, Updated easy dimming & daisy chain function, main light controlled, especially come with two waterproof and dimmable Mean Well Drivers, auto sensing power supply works on both 120VAC and 240VAC and 277VAC, suit for Large Rooms and Commercial Setups. Low Energy-Consuming LED Grow Light: Consuming 300w and also mounted with 1016 chips, TS3000 has the ability to replace a 450w HPS light while reducing 40% power intake. High Efficiency LED Grow Light: With overall light output PPF 343umol/S as well as amazing PPE 2.3 umol/j, it's 50% even more photon efficient and can assure a 30% more return than the old HPS/MH lights. Patent Highly-Reflective Hood Shape: The reflector design on TS3000 is patented, which can effectively gather the light dispersed in all directions to enhance its light intensity as well as assist plants in absorbing more light. Full Spectrum Plants Favorite Spectra: By the unique mix of spectra that makes most light in the 400-700nm waveband, incredibly conducive to plant photosynthesis. Adequate IR(730-740nm) is additionally consisted of in the range to generate larger buds. Dimming And Daisy Chain Feature Available: Upon an independent dimming button on the external driver, backing 0-100% settings adaptation and up to 30 LEDs daisy-chained in a group, it supplies different light levels for various plant stages meanwhile saving energy. Safety Certifications And Service Warranty: CE, ETL, RoHS, UKCA security certifications accepted, 50,000 hours durability, 5-year service warranty, and local after-sales repair 5x5 GROW TENT: LOCK ALL LIGHT INSIDE MARS HYDRO Indoor Grow Tent interior is made of diamond mylar which is highly reflective. (Other brand's mylar and reflective rate is as low as 50%, won't provide efficient light. )MARS HYDRO 1680D canvas, being double stitched, it is tear proof and has perfect light locking. Mars Hydro's grow tent keeps 100% lighting beams inside and helps your plant absorb more lights. EXTRA-THICK --No light leaks or rips at all DURABILITY GROW TENT Stable metal corner adapters and poles are the trustful supporters of the tent, standing sturdy, neither rusting nor paint-falling, quick easy tool-free installation. Mars Hydro's heavy-duty metal zippers, with double layer black lining, are the best on the market which create a light-proof seal EASY OBSERVATION FOR YOUR PLANTS. Special observation windows are made by double layers of cloth. Observe the growing conditions of your plants without opening the tent and avoid disturbing plants. The observation window also serves to dissipate heat and ventilate air AUTOMATIC 6 INCH EXHAUST FAN KIT W/ CONTROLLER: Mars Hydro 6'' Inline Fan uses a mixed-flow design to maintain peak performance in a high static pressure environment. GROW TENT FAN: MARS HYDRO inline fans are designed to ventilate hydroponic grow rooms, transfer heating/cooling, cool AV closets, and exhaust odors. EFFECTIVE VENTILATION: Variable speed controller for easy fan speed adjustment. Optimal ventilation for your planting. LOW NOISE LEVEL: Durable plastic fan housing and blades for extremely low noise(32dB-A); create a truly quiet growth environment. EASY INSTALLATION: Removable duct ends with locking tabs for quick removal and easy maintenance and a cord length of 4.9 feet for hassle-free setup. This grows tent fan with a controller for easy fan speed adjustment. BASIC PARAMETERS: Ventilation exhaust fan size: 6” | Dimensions: 315mm*225mm*210mm. | Weight: 2.7. | Airflow: 402CFM | Noise: 32dB-A | Bearings: Dual Ball. 

Mar 31 I think things are going very well, one plant has rusty spots, pretty sure its calcium deficiency, will be upping across the board. Got the runoff ppm to a good spot, will be going back to 800ppm feeds by week 8, 750ppm this week. I want more stable genetics next time, I am way to new to be dealing with basically 3 different strains, that's what it feels like, and I have very little time as it is. Thinking of upping PPFD some more, i think the droop of the one plant was just adapting to watering till runoff, I want to see some fattening AND RIGHT NOW.

WEEK 11 - 17/4/2021 - 23/4/2021 17/4/2021 - 20 gal water mixed with the following: Liquid silicon - 1ml/L - 76ml Cal Mag - 3ml/Gal - 60ml Micro - 2.5ml/Gal - 50ml Gro - 2.5ml/Gal - 50ml Bloom - 2.5ml/Gal - 50ml Fulvic acid - 2.5ml/gal - 50ml Hydroguard - 2ml/gal - 40ml Nitrozyme - 0.5ml/L - 40ml pH - 6.28 EC - 1.12 mS/cm T - 25 18/4/2021 - Plant 1 Moby Dick is the tallest and I have been consistently supercropping it to maintain even canopy with the other 3 plants. When the other 3 pkants have caught up with the growth, the suppercropped branch is straitened back and a soft twist tie. 21/4/2021 - I'll be away for few days. So I decided to go back Autopot for the few days I wont be around. I think it should be fine. Once I'm back, I'll go back to top feed and fertigate enough to have significant run off to wash off all the salt build up. 10 gallon of water mixed with the following - Cal Mag - 3ml/Gal - 30ml Micro - 2.5ml/Gal - 25ml Gro - 2.5ml/Gal - 25ml Bloom - 3ml/Gal - 30ml pH - 6.28 EC - 1.12 mS/cm T - 25 22/4/2021 - the Autopot idea didn't work out. The new tubing I got was 1mm bigger than its supposed to be. And thus caused leakage at all the connections. Well back to top watering then. But the plants won't be watered for two nights. I really hope they'll be able to hold on till I come back.

Hello growmies! Welcome to week seven of An Epsilon Adventure! Massive thanks to both Shogun and Royal Queen Seeds for sponsoring this grow! I have just completed the final defoliation for the three least advanced (and largest) girls. I have also rearranged the tent again to try to maximize the space available and light usage. I have not fertigated for 5 days after the last fertigation was a flush without coco base. I am struggling with humidity at the moment so I have been trying to let the plants go more dry than usual. Daily Updates ### Week 7 Day 2 02:30 7/8 Heavily defoliated plants 1, 5 & 6 and removed some of the lower branches. Rearranged tent then photographed & measured: Plant 1 is now almost unbelievably 2nd tallest at "only" 141cm in height! Her stretch has just about ended. Plant 2 has stopped stretching at 111cm and is 2nd most advanced into flower. Plant 3 has stopped stretching at 95cm and is most advanced into flower. Plant 4 has stopped stretching at 100cm and is 3rd most advanced into flower. Plant 5 has gained 6cm this week and may add few more but she is pretty close to done stretching at 119cm. Plant 6 has gained 22cm this week and isn't quite finished. She is now the tallest plant in the series at 142cm. ### Week 7 Day 2 07:00 7/8 Fertigated 1.6l each ### Week 7 Day 4 02:00 9/8 Fertigated 1.6l each reduced coco a/b to 2m/l each. Spent a bit more time photographing and videoing to try and capture the changes and the developmental differences. These 140cm+ plants are going to STACK. I am bracing myself for a lot of trimming and a monster harvest. 🙏 The current order of maturity and likely order of harvest is 3 2 4 1 5 6. I think the first and last plants will be at least a week apart in harvest, perhaps 2 or 3. ### Week 7 Day 6 23:00 11/8 Fertigated 1.6l each The smell in the tent is there now, really not that strong but there are 6 plants motoring through flower here now so it's not insignificant either. Plant 3 is absolutely stacking now, she's more or less run out of space around her cola and is now growing some foxtail like structures, exciting! Plant 6 the least mature is 2-3 weeks behind plant 3, but her stretch has finally stopped at 144cm. Took wide angle in tent photos today. All of the girls are drinking a lot now, but especially plant 1 who is really thirsty. --- Thanks for reading growmies! 👊 ========== Tent: 120cm x 120cm x 180cm Light: 600w HID Elite Dual Spectrum HPS + Angel Wing Reflector Air: 5" duct fan system with carbon filter ~300 m3/hour + RAM 9" floor fan + 4" intake fan Pots: Air Pruner Fabric Pots 30l - UGro XL Coco + horticultural grade perlite (~20%) Seeds supplied by Royal Queen Seeds https://www.royalqueenseeds.com Nutrients supplied by Shogun Fertilisers https://www.shogunfertilisers.com/en ==========

I did run into a few complications that hampered the grow.The 2 P's came into play on this one. PPM and PH I also had an issue with the pump art first but that was corrected quickly. I will grow this strain again in the future😎

Going well,and smell is nice 😊

Looking better and better each day Hopefully starting 12/12 before the plants fully revegged isnt super detrimental to the whole process.

Así están recién despiertas! Hoy tocó riego con estimulante s de floración ( topmax y bio-bloom) 2ml y 1ml/L 1 de biogrow por litrito!! Y hemos añadido el Activera de biobiiz también y tengo que decir que hoy están para arriba como nunca después de hace 8h que lo apliqué en el riego, seguimos controlando PH entorno a 6 puede fluctuar medio arriba o abajo, humedad superior al 50 pero no superior al 60 y esperando que se recuperen de las quemaduras del insecticidas con la luz :D se me fue tambien volvi a tamizar un poco de Microvita en las mecetas 🙂

Curing time soon.

Hey folks. Into week 6. Not much happening. Just letting the girls settle back in after the windstorm have em a good whipping. Just standard watering when needed and some lst here and there.

These two have been grooving. The bigger Bush plant vegged almost a week longer then the other. Only change was raised the nutrients to 1/2 dose. And increasing how often I need to water.its about to be a daily thing . They are hungry. I'm not complaining lol. But let's see how they fill out over the next 21days. Roughly at day 55 as of oct 25th !! Appreciate anyone checking in here. If u can leave a comment/like so I can check out what ur growing!!

Elle est extrêmement résistante 85% d’humidité tous le mois de septembre et beaucoup de jour de pluie, je ne l’ai pas protégé et elle tien le choque à merveille Les couleurs deviennent sublime elle devient entièrement violet et givrée de trichomes L’odeur est très fruité on peut pas rêver mieux en termes de terpènes j’ai hâte de goûter ça! J’en suis amoureux J’ai mis les données du mois de septembre en photo

Banana purple punch - 420 fast buds Week 6 had some issues with heat stress but seems to be pulling threw ok Smells banging DRSHOTZUK

Welcome back to another thrilling update on our Lego Ninja Tropical Tangie Run. Week 7 has been an exhilarating journey of rapid growth and breathtaking canopy development. Our Tangie is proving to be an extraordinary ninja superstar! Last week, we embarked on an exciting transplant adventure. Our fearless Tangie had outgrown her previous home, so we bravely transferred her to a spacious 25-liter fabric pot. With the assistance of Aptus Holland Mycor Mix, we ensured a smooth transition, providing her with beneficial mycorrhizal fungi. These underground helpers are like her very own ninja squad, supporting her root system and establishing a strong foundation. To continue supporting her growth and development, we incorporated the incredible Aptus All-in-One Pellets into the soil. These pellets act as potent ninja power capsules, packed with essential nutrients. Each watering session delivers the perfect dose of nourishment, fueling our Tangie's journey to greatness. She's thriving with optimal health and vitality. And let's not forget our loyal companions, the trusty Lego Ninja buddies. They have remained steadfast by our side throughout this green adventure, offering both moral support and an unwavering display of ninja vibes in the grow room. Who would have guessed that little plastic warriors could be such fantastic companions? After the successful transplant, it was time to introduce our Tangie to the art of scrogging. We skillfully installed a scrog net, creating a framework for her to weave her way through. This setup resembles a challenging ninja obstacle course, encouraging her to grow horizontally and maximize her bud production. It's truly remarkable to witness her impressive moves as she gracefully and sexily fills up the space. Of course, proper nutrition remains crucial for our Tangie's ninja training. Instead of using Aptus Holland Veg Watering Mix and All-in-One Liquid separately, we have now transitioned to solely relying on the pellets. These convenient premixed pellets integrated into the soil eliminate the need for additional liquid NPK. This simplification allows us to focus on other essential aspects of her training. To ensure she remains pest-free, we have been diligently conducting leaf picking sessions, which also serve as an opportunity to check for any unwanted visitors. So far, our Tangie has passed with flying colors, and her vibrant 9-fingered leaves are a fantastic sign of her overall health. As our Tangie continues her epic ninja journey, she basks in a PPFD of 600. These photons act as her loyal ninja training partners, stimulating robust photosynthesis and fostering explosive growth. With each photon absorbed, she becomes increasingly formidable, ready to take on any challenge that lies ahead. In summary, Week 7 has been an absolutely exhilarating chapter in our Lego Ninja Tropical Tangie Run. The successful transplant, the magic of Aptus products, the support of our Lego Ninja buddies, and the installation of the scrog net have all played vital roles in our Tangie's remarkable progress. We owe a tremendous SHOUT OUT to Aptus Holland, Dutch Passion, and Grow Diaries for their continued support and exceptional products for the love and for it all, without them nothing we see here wold be possible. Join us for the next update, where we will delve deeper into the fascinating world of ninja training techniques and witness the unfolding of our Tangie's extraordinary ninja powers. Until then, continue cultivating with joy, embrace the indomitable ninja spirit, and remember that every plant has the potential to become a botanical ninja superstar! As always thank you all for stopping by, for the love and for it all , this journey of mine wold just not be the same without you guys, the love and support is very much appreciated and i fell honored and blessed with you all in my life<3 <3 <3 #aptus #aptusplanttech #aptusgang #aptusfamily #aptustrueplantscience #inbalancewithnature #trueplantscience #dutchpassion #dogdoctorofficial #legoninjago #growerslove 
 With true love comes happiness <3 <3 <3 Always believe in your self and always do things expecting nothing and with an open heart , be a giver and the universe will give back to you in ways you could not even imagine so <3 <3 <3 Friendly reminder all you see here is pure research and for educational purposes only <3 <3 <3 Growers Love To you All <3 <3 <3