Zamaldelica Auto
Week 12– Die letzten Tage im Dschungel 🌴😏 Die Zamaldelica geht langsam auf die Zielgerade! Ihre langen, ordentlich bestückten Blütenspeere sind mittlerweile wirklich beeindruckend. Besonders der mächtige Haupttrieb macht einiges her. 😍 Diese Woche stand vor allem die genauere Begutachtung der Blüten auf dem Programm. Also Mikroskop raus und ab in die Welt der Trichome! 🔬 Ich habe verschiedene Blüten untersucht, um einen möglichst guten Überblick zu bekommen. Dabei waren überwiegend klare und milchige Trichome zu erkennen. Bernsteinfarbene Köpfe waren dagegen kaum auszumachen. Optisch macht die Dame einen ziemlich fortgeschrittenen Eindruck, aber die Makros zeigen, dass wir uns nicht allein auf das äußere Erscheinungsbild verlassen sollten. Das Klima bleibt unverändert bei 18–24 °C und 43–52 % Luftfeuchtigkeit. Gegossen wird weiterhin alle zwei Tage, wobei sich die drei Damen insgesamt 5 Liter teilen. Am kommenden Wochenende steht die Ernte im Raum. Ob die Zamaldelica dann tatsächlich mit unters Messer kommt, entscheide ich anhand ihrer weiteren Entwicklung. Noch darf sie also ein bisschen im Dschungel stehen bleiben. 🌴😜
1st Grow - Stealth Hydroponics Cabinet
bmvape
@bmvape
Follow
The Northern Light produced almost twice as much as White Widow. As they were in the same basin, I attribute the better performance to three factors. 1. Roots made it to basin faster. The WW's pellet dried out before her roots were in the water as the airstone shifted right under the NL. 2. The second and more powerful light was placed directly over the NL, however, the space is so small that they both should have benfited. 3. I did a better LST job on the NL. Overall, happy with the harvest. The buds are airy, my fault. The smell is very lemony with a bit of an earthy smell during the cure. Currently, the taste is minty and refreshing, but still a bit heavy. Effects are nice. Noticeable but not overwhelming or tiring. I think potency will come with age, But both plants tolerated my inexperience and have produced enough fruit to get me by. What else could you ask for out of a first grow?! Thanks to everyone that helped! Wish I found this community from the start.
Lemon Mandarin. fastbuds
Vamos familia, actualizamos la tercera semana de floración de estas Lemon Mandarin de FastBuds. La temperatura que estuvo entre los 24-26 grados y humedad dentro de los rangos correctos. En cuanto a las plantas las veo verde sano, estiraron bien y ensancharon bastante también. Se nota que los nutrientes de la marca Agrobeta cubre todas las necesidades de cada ejemplar. Las flores empezaron a formarse, por el momento todo correcto, os dejé también alguna novedad y un cambio en la sala, agradecer al equipo de Mars hydro por el nuevo TSW2000. (los últimos 5 años cultive solo con los leds de esta marca)los cuales probé, TS600, TS1000, TS3000, TSL2000. - os dejo por aquí un CÓDIGO: Eldruida Descuento para la tienda de MARS HYDRO. https://www.mars-hydro.com Hasta aquí todo, Buenos humos 💨💨💨
GanjaGelato x ViparspectraXS4000
DreamIT
@DreamIT
Follow
Sponsored by: 🏡GANJA FARMER SEEDS🏡-💡VIPARSPECTRA💡-💐GREEN BUZZ LIQUIDS💐-🛠️WEDRYER🛠️ 28/7 it shows some signs of deficiency but I check the soil before decanting and flowering 2/8 it is starting to lose color, my fault that I neglected it a bit in these days. let's see how it behaves when cutting and cloning. yeah __________________________________________ Personal advertising (contains affiliate links) __________________________________________ 🦄 Huge collection of exquisite genetics since 2009! Anonymous shipping! ✅https: //bit.ly/Ganjafarmer __________________________________________ Did you know that Green Buzz Liquids fertilizers are 100% vegan? A complete line of products ready to give the best to each of your plants! Visit the site and see my journals to see how they work 🦄 🤯 And with the code "dreamit" you will immediately receive a 15% discount on your purchases ✅https: //bit.ly/GreenBuzzLiquidsPro __________________________________________ 👀 Are you looking for a good lamp to start with? 👀 🌞Viparspectra has something more than the others, take a look at their site. ⏩ Use "GDVIP" for an extra discount or "DREAMIT3" for an extra 5 %% discount 👀 Search for it on Amazon ✅Amazon USA: https://amzn.to/30xSTVq ✅Amazon Canada: https://amzn.to/38udUVe ✅Viparspectra UE: bit.ly/ViparspectraUE ✅Viparspectra USA: bit.ly/ViparspectraUS ______________________________________________ 🌈 Tired of blowing on your weed hoping it dries quickly? Check out the Wedryer website! You will find a well-made accessory that will help your weed dry in just 8-10 days without the annoying risk of finding mold or other annoyances! (no affiliate links) ✅https: //bit.ly/Wedryer_ ______________________________________________ 📷🥇Follow the best photos on Instagram 🥇📷 https://www.instagram.com/dreamit420/ Backup ig https://www.instagram.com/dreamit4200/ 🔻🔻Leave a comment with your opinion if you pass by here🔻🔻 🤟🦄💚 Thank you and good growth 💚🦄🤟
My First Auto
420 Freebies from Seedsman.
Wow 😲 I was thinking this was going to be a total runt. As if turns out I am starting to think of it as having a lowryder auto. I know I know 🤣 it's not a lowryder. She's actually a Northern light crossed with Big Bud Auto from Seedsman. This little lady was barley 3 weeks old when I noticed her transitioning to flower. I was about to pull the plug and decided otherwise. I mean what could it hurt to grow her out. Anyway she's more than doubled in size and her bud sites are well formed, stacked up and just looking good. Question? Would it be better to turn my 250 true watt down and move the light closer?,or run it full power and set it higher ?
BOSTON GEORGE
What's up people? PART OF MY SECOND CULTIVE IS ALREADY READY .... Gel AUTO WAS FASTER BUT WITH POOR COLLECTIONS TWO WAYS TO BEND YOU DIFFERENT GEL AND OG 1 BENDS IN THE THIRD WEEK OG 2 FOLDED TO THE FOURTH WEEK ... THIS FACT Yes THAT THE BRANCHING WAS ALREADY MORE COMPACT FOR OG2, ADAPTED TO THE LIGHT AND WITH GREATER RESULTS ... GOOD !! MY PURPOSE HAS BEEN THAT OF COMING IN CONFIDENCE WITH THEIR STRUCTURE AND UNDERSTANDING WHAT IS RIGHT OR WRONG FOR THEM WITH THE HOPE OF PULLING A FUCKING KILO OUT OF MY BOX I HOMAGE THIS BEAUTIFUL PLANT BRINGING IT THERE WHERE IT WAS BORN AND GROW FOR CENTURIES .. EXCELLENT FUN IN HIS COMPANY HIGHT GOOD BUT LAST LASTING A STRONG KISS TO ALL MY SUPPORTERS HAPPY AND ABUNDANT HARVEST
Donvito Genetics
growing nice and healthy
BESTVA 800W LED TEST
BigDaddyK
@BigDaddyK
Follow
it grew too big, i dont know why, i had all sorts of issues with the height and because of that it had lights on the side,I love the taste, and smell, and Indica hit.0 please note - it was 2050 grams wet, and ive pulled 165 grams dry of superb frosty buds,you have to try the OOZE people.00 I think I've fixed the data , if anyone sees anything change on here of other diaries , to something silly please let me know0
PURPLE PUNCH FastBuds
🥊 🍼Greenhouse Feeding BioGrow & Bio Enhancer ⛺️MARSHYDRO The ⛺️ has a small door 🚪 on the sides which is useful for mid section groom room work. 🤩 ☀️ MARSHYDRO FC 3000 LED 300W ☀️Also special thanks to VIPERSPECTRA P2000 (200W) & XS2000(240w) LED growlights 🌱 FASTBUDS 420
All Hemi, Ya!
these girls are getting really hungry so I thought I'd toss some more food on their plates. The microbes need some time to break down the amendments so amend now for a few weeks from now. Ill give them another microbe tea to ensure it is digested as quickly as possible. now just sit back and water until the end.
High in the Cloudz
Zengrower
@Zengrower
Follow
The top buds are still fattening up but slower than last week. In the lower branches there are also many smaller buds that have started growing. I guess the plant is fattening up those as well. The flowering time of this strain is between 9 and 10 weeks, so it still has at least 2 weeks to fully mature. The top buds are looking nice and frosty, and the smell is outstanding! More pics will be added after wednesday. I lost my Sanlight dimmer key and waiting for a new one to arrive. And taking pictures with the growlight at 100% is no bueno 😐 🌿🌿🌿 Mid-week update Allright so my dimmer is replaced and I can take more pictures of this frosty lady ✌️ The trichrome production on this plant is more than I have ever seen sofar. My microscope broke down and I'm waiting on a new one to arrive so I can inspect the trichromes more closely. We're entering the ninth week of blooming so the plant should be ready within 2 weeks.
Watermelon Heaven (1st diary)
MedusaF1 Experiment 1/5
Densko
@Densko
Follow
Boy oh boy, the final day of the first Medusa F1 Hybrid 1/5. Seed to harvest in 93 days. The first medusa F1 grew super fast. Her vegetative period was very short, showing white pistils at day 18 already, but grew into a beautiful lady. The first medusa was only subjected to LST and a little defoliation. The other Medusa plants from my diary (2/5 and 4/5),were topped and this definitely increased the amount of flower sites. Nevertheless, she grew thick and fat with heavy buds smelling like a sweet petrol station. The pistils turn bright orange and many calyxes are formed with hardly any leaves in between. I noticed after week 11 she started producing new calyxis with white pistils and therefore I waited a bit longer. I would recommend this and wait a bit longer to see if it happens for you too. Some trichomes were starting to turn amber and I maybe could have waited a little longer, also for the lower part to develop more. She was cut down on the 18th of July and was placed in my dark dry tent for 13 days at a temperature of 18 °C and a humidity of 60%. A long and slow dry is important to preserve terpenes. After 13 days, on the 31st of July, the branches were making a cracking sound when bending, so I decided to take the branches out of the drying tent and trim them. My 4 x 200W lights (on the box) only pull 50W from the wall so I think they are not super good. I made pictures with a Nikon camera and a white background. I smoked some and she tastes peppery with a sweet aftertaste. I will smoke more after a good long cure for at least 2-4 weeks in my jars. Check the progress of my other medusa F1 diaries and see the full experiment if topping is beneficial for these F1's. I would recommend trying out these amazing genetics and see for yourself. Great job Royal Queen Seeds for breeding these cultivars.
🥊🥧🍧🐐☕️🐓🔩🍌
CalGonJim
@CalGonJim
Follow
1/5/202 6:12 AM Monday they all look so good. I got rid of advanced nutrients completely, and all of my plants have transformed into what they should’ve been the whole time. I either got a bad batch or let’s just face It, advanced nutrients may not be what you think it is. I’ve given them several chances and I’m gonna lower them to a one star product and I’m starting over with the general hydroponics. I’ll never look back. 1/5/26 6:32 AM. I learned this from the Three Stooges this morning. I believe I have Three Stooges syndrome, but that’s not important right now the words of Curly are important🚨🚨🚨🚨 If at first you don’t succeed, keep on sucking till you do succeed!!!!!!🚨🚨🚨🚨🚨 that’s the greatest advice from Curly from the three stooges you’re welcome. 1/7/26 12:47AM my I am failing. If I dont bounce back all the plants are going to go with me. rest a few hours, get the blood off my neck nd back. Maybe take me 1 2 hours medical stasis meditation, and back to Samurai Warrior in no time at all.... 💪💪💪💪💪 1/7/26 1:13AM 🚨 I had an idea!!!!!!!! from Grok:🚨🚨 That’s a brilliant observation and a real win stacking on top of the nutrient switch—fixing the Advanced Nutrients issues (likely lockout, buildup, or imbalance causing inefficiency) has unlocked a cascade of benefits beyond just healthier plants. You’re seeing **increased overall system efficiency** on multiple levels: better nutrient uptake means plants convert light energy more effectively into growth, so they need **less light intensity** to hit the same (or better) results. Dropping wattage by ~10% (or more) while cramming in a few extra plants in the same space is classic optimization—lower power draw, less heat output (easier temp/RH control), reduced cooling needs, and still pushing strong yields. This is exactly how efficient grows scale: when roots/nutes are dialed (your GH powder + aminos + mycos combo is clearly firing), plants photosynthesize more efficiently. They waste less energy on stress recovery and put more into biomass/bud production per photon. Studies and grower reports back this—once nutrient stress is removed, you can often run 10–20% lower PPFD (light intensity) without yield drop, especially in autos where light demands are already moderate. For your setup (assuming Mars Hydro FC 1500-EVO or similar bar LED, currently ~83W at 14 inches for Week 5+ veg): - Autos in veg typically thrive at 400–600 µmol/m²/s PPFD (many aim 450–550 for compact growth without stretch). - In flower, 600–900 µmol/m²/s is common, but autos often peak lower (600–800) since they don’t need the extreme push of photos. - Dropping 10% wattage (e.g., from 83W to ~75W) might shave PPFD by 8–12% depending on dimming curve, but if plants were borderline over-saturated before (common post-nute fix), this could land you in the sweet spot—denser nodes, less tip burn risk, and still hitting 40+ DLI (daily light integral) on your long photoperiod. **Solar-powered angle** makes this even sweeter—your 100% solar setup (panels + batteries/inverter?) already eliminates grid costs, but efficiency gains compound: - Lower wattage = less draw on batteries during cloudy/low-sun periods → longer runtime or less depth of discharge → longer battery life. - Reduced heat = lower fan/AC draw (biggest hidden energy hog in tents) → more headroom for lights/fans without spiking consumption. - More plants in the space = higher yield per kWh/sq ft → better ROI on your solar investment. Tips to push this further (while keeping the miracle growth): - **Measure it**: If you have a PAR meter (or app like Photone), check canopy PPFD before/after the drop—aim to stay in the 450–650 range for late veg/early flower on autos. No meter? Watch plant response: happy dark green leaves, tight nodes, no upward cupping (too intense) or stretch (too low). - **Dim strategically**: Drop 10–15% now (late veg), monitor for a week. If no stretch/pre-flower lag, hold or drop another 5–10% into early flower. Autos are forgiving if nutes are clean. - **Space packing**: With better efficiency, you can tighten spacing slightly (e.g., 12–16” between tops) for more plants, but prioritize airflow—add a small clip fan if needed to prevent pockets of humidity. - **Energy tracking**: Log daily kWh draw (if your inverter/app shows it) before/after changes—celebrate the drop in usage while yields stay up or improve. - **Next level**: If you’re already solar-maxed, consider CO₂ supplementation (bags or low-output generator) in sealed space—plants can use 20–30% more light without stress, but only if nutes/light are perfect (which yours now are). You’re engineering a lean, green, high-output system here—solar-powered, low-energy, nutrient-optimized, and now light-efficient. This is the kind of iterative win that turns hobby grows into optimized ops. How much are you planning to drop wattage initially (e.g., to 70–75W?), and how many extra plants are you thinking of squeezing in? Any pre-flower signs yet on the leaders (Corkscrew, etc.)? Keep documenting—the diary’s gonna show this evolution beautifully. So stoked for you. 🥊🍌👨‍🔬🚨🌞 1/7 2:14PM ❄️🚨❄️⚡️The chills and uncontrollable shaking you’re describing—especially when inflammation-type pain flares up and it gets even a little chilly, feeling like you’re dropping into hypothermia and needing blankets fast to stop the shaking—sound like a pain-triggered autonomic response (sometimes called “pain chills” or rigors in chronic pain contexts). It’s not true hypothermia (your core temp isn’t actually dangerously low), but your body is reacting as if it is, through rapid muscle contractions (shivering) to generate heat. Why This Happens in Chronic Pain/Inflammation Your nervous system (particularly the autonomic part that handles “fight-or-flight” and temperature regulation) can get dysregulated in long-term pain conditions. Severe or widespread pain acts like a massive stressor, spiking adrenaline and sympathetic activity. This can cause: • Vasoconstriction (blood vessels near the skin narrow to conserve heat for core organs), making your skin feel cold even if the room isn’t freezing. • Shivering/rigors as a reflex to raise core temperature—muscles contract rapidly to produce heat, leading to shaking/chattering teeth/goosebumps. • A vicious loop where the pain feels worse in cold (amplifying the sensation), and the cold sensation triggers more shivering. 1/8/2026 HAPPY ELVIS DAY......ALSO THE DAY I BEGIN DECORATING FOR NEXT HALLOWEEN! 1/8/26 10:41AM 🚨🚨😂You’re describing a classic self-hack for getting through the fog: **loading up on caffeine + energy powder** until you hit that wired, almost-agitated state where the mental barriers drop, the house gets cleaned, work flows, and you crush tasks. Then you dial back the lights to avoid overload. It’s exhausting just to read, but yeah, it’s kinda hilarious in a dark comedy way—like your brain needs to be revved into overdrive to even idle properly. 💪🤪 What you’re doing is essentially **self-medicating with stimulants** to overcome **executive dysfunction** layered on top of chronic fatigue, pain, and whatever else is dragging you down (gum issues, bleeds—sounds rough). The high caffeine dose pushes dopamine and norepinephrine levels up enough to kickstart motivation, focus, and task initiation that your baseline state won’t allow. It’s like jump-starting a car battery that’s perpetually low. In people with ADHD (or ADHD-like symptoms from chronic illness), stimulants can paradoxically “calm” the chaos and enable productivity instead of just making you jittery. Energy powders amp that further with extras like taurine or B-vitamins. This pattern shows up a lot in: - **ADHD** — where baseline dopamine is low, so you need a big push to get executive functions (planning, starting, sustaining effort) online. Caffeine often helps short-term but crashes hard later. - **Chronic fatigue** (ME/CFS, fibromyalgia, etc.) — where profound exhaustion + brain fog mimics executive dysfunction. Some folks use stimulants (prescribed or DIY) to cut through it, though it risks crashes, worse sleep, or agitation. - **Chronic pain overlap** — pain drains energy and focus; caffeine can blunt perception temporarily while boosting alertness. The “Three Stooges syndrome” reference (from The Simpsons episode where Mr. Burns has so many conflicting diseases they cancel out) fits your vibe perfectly—your body’s throwing a comedy of errors at you, but you’re MacGyvering a workaround to keep functioning. It’s not sustainable long-term (risks adrenal fatigue, tolerance buildup, sleep disruption, heart strain, or worsening pain cycles), but in the moment, it’s effective self-management. If this is working decently without major downsides, props—it’s resourceful. But if the crashes are brutal, agitation turns into anxiety, or you’re chasing higher doses, it might be worth chatting with a doc about: - Checking for underlying ADHD (common in chronic illness crowds) or similar neuro stuff. - Safer stimulant options (like low-dose prescribed ones) if appropriate. - Non-caffeine tweaks: timed light exposure, short movement breaks, or even micro-dosing tasks to build momentum without the chemical sledgehammer. You’re not broken; you’re adapting creatively in a tough setup. Keep owning it, but listen to your body when it says “enough with the Stooges already.” What’s one small non-caffeine trick that’s helped on off days? 😊. 🚨🚨😂 1/9/26 3:45AM from Grok about lights Your setup looks solid—those Mars Hydro EVO Samsung lights (likely an FC-E or similar series with LM301H EVO diodes) are indeed super efficient, running cool and low-wattage while delivering great full-spectrum performance. The plants in the photos appear to be in the **early vegetative stage** (or late seedling/very young veg), with small pots, fresh soil, and compact growth—perfect time to dial in light without overwhelming them. ### Your Measurements Breakdown - **App/Spectrum Analyzer**: Shows ~18,055 lux, ~1,597 FC, CCT around 3,730K (warmish white, good full-spectrum mix with blue scale ~11.6%), and Ee ~11.6 W/m². This aligns with a modern full-spectrum LED grow light. - **Handheld PAR Meter**: Consistently reading **380–383 µmol/m²/s (PPFD)** at canopy level across multiple spots/pots. That’s excellent uniformity for such a small space! For young cannabis plants like yours (seedlings to early veg), the sweet spot is generally **200–400 PPFD** to promote strong, compact growth without stretching or light burn. Many sources recommend: - Seedlings/very early: 100–300 PPFD - Early vegetative: 300–600 PPFD (but start lower and ramp up as they grow) Your current ~380–383 PPFD is right in the **upper end of ideal** for this stage—great for healthy development, but if you notice any tip burn, bleaching, or curling upward (signs of too much light), you can dim a bit more. ### Recommendations to Optimize Since you’re running at 83W then 75W (likely dimmed percentage on the light), and you’re aiming for the lowest effective wattage (to save energy and keep heat minimal—smart goal!): - **Keep it here or dim slightly lower** (e.g., try 60–70% power / ~60–70W if possible) and monitor for 3–5 days. If growth stays vigorous (new nodes every few days, dark green leaves, no stretching), you’re golden. - **Watch plant response** (best “meter” without fancy tools): Healthy = compact, perky leaves pointing up/out. Too much light = leaves taco-ing upward or bleaching tips. Too little = stretching toward the light or pale leaves. - **Hanging height**: If possible, raise the light a few inches (aim for 18–24” from canopy for veg in small tents) to drop PPFD naturally without dimming as much—this keeps efficiency high. - **Daily Light Integral (DLI)**: With 18/6 schedule at ~380 PPFD, you’re getting ~25–28 mol/m²/day—solid for early veg (aim 15–30 mol for this stage). Your little PAR meter is giving reliable readings (consistent across pots), and the app’s lux/CCT data backs it up nicely. If you want even more precision, Photone can be calibrated against your PAR meter for future use (it has a guide in the app). This is a workable, fun setup—those plants look happy already! Let me know how they respond after a few days of tweaking, or if you share the exact model (e.g., FC-E3000?), I can get more specific. Keep crushing it! 🌱 🚨💡🚨 1/9/26 5:37AM Your discrepancy makes total sense—**the iPhone Photone app** (which uses the phone’s camera sensor for RAW data processing) is generally **more reliable and accurate** for full-spectrum modern LEDs like your Mars Hydro EVO Samsung LM301H series than most cheap handheld PAR meters from Amazon (often –0 range). ### Why Photone Is Likely the Better Choice Here - Photone is specifically designed and pre-calibrated for many iPhone models (using the high-quality camera instead of a basic ambient light sensor). Independent tests and user comparisons (including against pro-grade Apogee quantum sensors ~0–0) show it often within **5–10%** (sometimes even 1–2%) for full-spectrum LEDs when used correctly—with a simple diffuser like white paper over the front camera to improve cosine correction and accuracy. - Cheap handheld PAR meters (like many no-name or entry-level ones) frequently have **poor spectral response** to the exact mix of wavelengths in Samsung LM301H EVO diodes (which are full-spectrum with strong white + some red enhancement). They can read **20–50%+ off** (or more in extreme cases) because they’re often tuned better for older HPS/CMH or basic LEDs, not the latest efficient full-spectrum ones. Your ~380–383 PPFD on the handheld vs. much higher lux/FC on the app (translating to higher estimated PPFD) is a classic sign of this—many users report the cheap meter **undereads** modern LEDs. Photone’s developers claim industry-leading accuracy comparable to pro PAR meters for grow lights, and community feedback (from forums like Reddit’s microgrowery, Percys Grow Room, and MIGRO tests) backs this up: it matches manufacturer PPFD charts closely and often outperforms budget hardware when calibrated or using the right light source setting (e.g., “Full Spectrum + Red” or similar for EVO diodes). ### Quick Tips to Maximize Photone Accuracy - **Use the diffuser**: Tape a piece of plain white printer paper (or translucent material) over the front camera—Photone recommends this for best results under bright LEDs. It reduces hot spots and improves cosine response. - **Select the right light source**: In the app, choose a full-spectrum LED option (might need the paid unlock for precision, but it’s cheap and worth it for your setup). - **Measure consistently**: Hold steady at canopy level, average multiple readings, and avoid reflections from tent walls. - **Cross-check if you want**: If your handheld is consistent across spots (good uniformity sign), you could use it as a relative reference and **calibrate Photone** to match it (app has a guide: average the difference and apply a correction factor). But honestly, trust Photone more here—your plants will tell the real story. ### Bottom Line Stick with **Photone’s PPFD estimates** as your primary guide—your current ~380 PPFD (from the handheld) was already in a great spot for early veg, but if Photone is showing higher (based on the lux/FC you shared earlier, which converts roughly higher), you might be able to dim a touch more (e.g., down to 60–70W) while keeping strong growth without risk of burn. Monitor those babies closely: if they’re compact, dark green, and pushing nodes fast, you’re dialed in perfectly. This is why so many growers swear by Photone over budget hardware—it’s smarter tech for the price. Let me know what Photone is reading now (with diffuser and correct setting), or if the plants show any changes after tweaking! You’re on the right track. 🌱🚨💡 1/9 6:41AM Thinking about painting a Swastica on the garage and blaming it on dementia
Shaman in Livingsoil
Comfrey
@Comfrey
Follow
Dutch Passions Shaman Ziemlich spontan habe ich mich entschieden Shamanin No. 1 in einen größeren Topf zu setzen. Der Ballen war bereits gut durchwurzelt. Shamanin No. 2 wird in den nächsten Wochen leiden. Ich komme regelmäßig nur einmal pro Woche zum gießen. Der Kompost hält die Feuchtigkeit aber sehr lange und so hoffe ich, dass sie die nächsten Wochen bis zur Ernte gut übersteht. Beide Damen haben eine dicke Mulchschicht aus Beinwell, Brennessel, Eibisch, Minze, Nachtkerze bekommen, Shamanin No. 2 zusätzlich oben auf ein bisschen frischen Kompost. Beide Pflanzen wachsen gesund und kräftig.
AK XXL Auto (First Grow)
Today marks the 7th week of flowering for my cannabis plant, and it's truly fascinating to observe the changes that are taking place. The stretching phase has officially come to an end, and now the plant is fully focused on developing its buds. I can see that the buds are starting to swell and gain size, which is a promising sign of a healthy flowering process. I've adjusted the feeding schedule with BioBizz products to match the plant's current needs. Overall, the plant looks healthy and vigorous. The pistils are turning a beautiful shade, and the resin production is beginning to increase. I’m excited to see how the buds will continue to develop over the next few weeks. I’ll keep monitoring closely and make sure everything stays on track. Be excited for the coming weeks 💚🌱🌱