By continuing to use the website or clicking Accept you consent to our cookies and personal data policy and confirm that you are at least 18 year old. For details please see Privacy Policy and Terms
In my home i has water with 20PPM. The agro wool is installed in glass with rounded edges, disinfected from the beach. Pot with glass in a 10 liter bucket. Two stones for air. Exhaust 200m per hour from the box.
During the first week I noticed algae at the base, the result: it was better to block it from the light. And I stretched out a lot because I turned on the lamp weakly, 100 watts at 15 percent, increased it to 30 percent. Fertilizers are just a base.
chlorosis appeared, and there was dead tissue on the edges of the leaves, the result: I tried to treat it with a spray from Kalmag because the water from the tap is very clean, 40 PPM, after a couple of days the color of the leaves became normal, but the dead tissue naturally did not come to life) I treated it this way 2 times a week.
the leaves began to curl up in places where they were damaged, I increased the concentration of the solution, added fulvic, and after changing the solution it grew well within a week. I treat it with Kalmag spray once a week.
carried out topping after the 4th floor. I transplanted it into a 20 liter bucket because the root is already large. I installed chipboard for LST, made a hole in a bucket, placed a pot with glass and roots there, put chipboard between them, the bucket is round and therefore it is possible to rotate the chipboard 360 degrees, convenient for LST. Light 100 watts at 90 percent.
The bush began to stretch, the bush began to consume a significant amount of solution, and increased the concentration to 450 PPM. I live in a southern country, and therefore the temperature became high although only one 100W lamp out of three was turned on) the solution was to add air +100 meters per hour using a corrugated duct directly to the bush. I hung three lamps and turned them on to 30 percent in the hope that they would heat up less) large leaves began to die, I started treating them with Kalmag spray again
I continue to stretch all the shoots every two days. the temperature continues to rise due to the weather and the bush is still growing and I increase the light of the lamps, solution: I made a screen of plastic glass for the lamps, 10 cm at the edges for air, the temperature does not rise above 27 degrees Celsius. Large leaves continue to die, the source of the problem has not yet been determined. The bush consumes fertilizer well; I increased the solution to 550 PPM. I added a set of fertilizers for the roots, and they began to grow noticeably.
Pre-bloom has begun, growth is excellent and there are a large number of new leaves, little by little I begin to prune the largest ones. Dark spots appeared on the roots, solution: added 3%-100ml hydrogen peroxide to the solution. by the end of the week the spots stopped appearing. The bush began to consume more than 2 liters of solution per day and lower the salt level, increasing it to 650 PPM. I added fasteners to the sides of the chipboard to make it possible to hang the bush. Replacing and monitoring the solution has become much more convenient.
the second week of pre-flowering, the roots have increased three times in two weeks, I actively stretch and cut off the leaves every two days, the average amount of solution consumed is up to 4.5 liters per day by the end of the week. Added a fan, humidity 80 percent (((
started flowering, excellent growth of leaves and roots. I remove leaves that interfere with the inflorescences and create a tight cluster. The light is 100 percent, 3 lamps of 100 watts each, it’s 26-30 degrees outside, the humidity is almost 90 percent, the air conditioner doesn’t help much. PH began to fall, added hydrogen peroxide, and by the end of the week it stopped falling.
inflorescences are actively increasing. I raised the lamps so that the temperature did not rise above 28 degrees at the top of the bush. I stretch the branches so that the tops of all are at the same height, so they all grow the same.
Dark spots began to appear on the roots again; I removed them partially with peroxide. The consumption of fertilizers has increased, increased to 750 PPM. At the end of the week I went to flahsclean for a couple of days before rippen.
A couple more days of cleaning and switched to rippen. The humidity outside is 98 percent!!! 30 degrees!!! I feel bad when I go outside during this period. I'm surprised how the bush continues to grow and consume so much liquid. To solve the heat issue, I used: an additional air channel directly to the bush, a screen for heat removal made of plastic glass under the lamps, a fan, an air conditioner in the next room, an exhaust hood to the street.
The last week has been ripe, the smell is wonderful, the flowers are still growing. I increased the content to 1000 PPM, at the end of the week it showed too much and began to return 1200 PPM.
switched to cleaning, looking at the trichomes, while most are white, I was waiting closer to 50/50, I like the effect of CBD. It took another week until it was ready.
growing for the first time, in a southern country, and flowering in the hottest month is a test, and judging by the result, I passed well. The question remains, why did the large leaves turn yellow at the beginning of the cycle? I hope next time I will find the answer)
Vik13
