Samen herstellen

When a female cannabis plant is treated with a solution of tiny silver particles suspended in distilled water, the plant will start to exhibit male characteristics. This solution of silver in water is called colloidal silver and can be purchased from a pharmacy/online or easily made at home {instructions below}. Or you can make it with a colloidal silver generator. Some people drink colloidal silver for its health benefits and others use it occasionally on plants to help control bacteria, insects, and fungus growth on the leaves. To take advantage of this, you thoroughly mist a female cannabis plant with colloidal silver every day right when she enters the flowering stage, she will start growing male “balls” full of pollen. Keep misting the plants daily until you see the beginning of male pollen sacs forming, usually around 10-14 days. The concentration of silver ions in the water acts as an ethylene inhibitor/antagonist on the plant, which forces the plant to create male pollen sacs instead of female buds. After the balls start forming You need to let the sacs swell like a big empty balloon. You will be able to tell when they are about to open because the leaf section protecting the pollen starts to crack. At this point, simply take the pollen sacs off and place them in a cool dry place for a week and let them start to dry. The pollen will come out if you shake them about a little, or you can also cut open the sacs to get to the pollen inside. Use this pollen to pollinate female plants and you will get all-female seeds that are a mix of both their mothers. This method is great because it will force almost any female cannabis plant to show male characteristics. The one downside to this method is that it is not safe to use any cannabis that has come into direct contact with colloidal silver. You should, therefore, destroy the plant after the pollen has been collected. You will also want to ensure that you clean any remaining traces of silver off your equipment in case you accidentally contaminate another cannabis plant with silver. Here are the main things to keep in mind when using the colloidal silver spray method: Make sure you spray the cannabis with a strong enough colloidal silver solution (at least 30 PPM of silver) Spray the cannabis thoroughly to almost drench all the parts you want to turn into pollen sacs Spray the cannabis regularly, at least once a day for 10-14 days, starting when you change the lights to 12-12 Spray the cannabis with colloidal silver every day until you see signs of male pollen sacs forming. Some hardy strains may need over 2-3 weeks spraying before they ‘turn’. Where to Get Colloidal Silver Colloidal Silver is created by submerging two pieces of pure silver in distilled water and then running an electric current between the two pieces of silver. The electric current will cause silver ions to be deposited in the water which creates a colloidal silver solution. Buy Colloidal Silver: You can buy colloidal silver which has already been prepared and is ready for use. If you’re purchasing colloidal silver, try to find a solution that has at least 30 PPM (parts per million) of silver. However, buying Colloidal Silver that is already prepared can get expensive. Buy A Generator Kit: A better option is to buy a relatively cheap colloidal silver generator to easily make your colloidal silver. This Colloidal Generator kit comes with everything you need including silver. All you need to do is provide the water and a container. Make Your Own: You can make your own colloidal silver generator at home. The diagram below should illustrate what you need to do. Items Needed: 9-volt battery 9v Battery Connector (less than at a hardware or electronics store) Pure .9999 or 999 Silver (yes it must be pure) Distilled water (yes it must be distilled) Alligator clips (Optional: but will make things much easier) Soldering Iron (Optional: only needed if you want to use alligator clips) How to easily make colloidal silver at home for use with creating feminized cannabis seeds The diagram above will show you how to easily make colloidal silver to make feminized cannabis seeds When you first connect everything, you may be surprised because it will seem like nothing is happening. You will know if it worked by the next day because the whole process will leave a silvery residue on your silver. You may need to use sandpaper or something else rough to clean your silver each time after creating a batch of colloidal silver. If you don’t have a soldering iron and would still like to solder alligator clips onto your battery connector, then I recommend going to a hardware store and asking someone if they will help solder it for you. Remember to keep your resulting colloidal silver solution away from any light or it will deteriorate and turn a dark gray color. If this happens, then you can no longer use the solution for creating feminized seeds. Avoid most problems when making colloidal silver by: using pure (distilled) water using pure (999/.9999) silver giving electrolysis enough time to work so you don’t get a weak solution (at least overnight) make sure the solution has as little contact with light as possible until you use it