The little ones are developing well, unfortunately there are a few minor nutrient problems in the direction of Calmag with the Morello Cherries and also slight signs of this with the TerpyZ Punch. I counteracted this with a foliar spray. The pH value of the hydrosystem has unfortunately dropped a little to 5.5, which I have equalised with ph up from Plagron. The plants are currently getting light between 800-900 ppfd and as soon as the stretch starts, l'll increase this to 1000 ppfd. Both ladies are slowly starting to smell.

Esta es mi primer planta que cosechó con éxito, y estoy muy feliz con mi resultado final 😄 obtuve una muy buena cantidad de flores premium con alrededor de 15% de thc (desde mi punto de vista claro 😅) Tuve algunos problemas durante el cultivo, principalmente que deje que se estirara mucho, debi hacerle LST a la punta principal para que no siguiera aumentando la altura y tener más flores del mismo tamaño, las flores más bajas quedaron chicas y les faltó madurar un poco, también tuve problemas de sobrefertilizacion aun a pesar de que seguí las instituciones de los fertilizantes y de sus indicaciones que me dieron los de servicio al cliente, incluso ya teniendo en cuenta eso siempre use la menos de la dosis de la base ya hasta que crecieron más le fui aumentando, igual creo que es muy cierto lo que dicen de que “menos es más” a la próxima empezaré usando muy pocos nutrientes, aparte creo que si hubiera usado unos leds más potentes, las plantas hubieran aprovechado más los nutrientes, pero igual me sirvió de experiencia, pienso cultivar de nuevo esta genética y sacarle más provecho. Muy recomendada 👌🏻😁

Doing good

It was a very good experience for me because they were most bigger and higher than when you using soil, I didn't expect that)) It was my first time when I used DWC...

🍃🌱🤯

2022-09-17 The journey of the Hella Jelly is over. Plants were supereasy to grow. all Seeds germinated, seedlings started strong, and in later Vegetation they were spreading. here they spuld have got more Training from me. Because they turned out quite bushy The branches had to carry Biiiig green Buds , covered with frosting and were bending over in the End, so they needed some Support. I was alittle worried because the Pistils stayed white/ green. then i read the straindescription and looked at Pictures again and i knew everything is fine Iam harvesting with cloudy/ amber Trichomes. Plants leaves were also fading and changing to autumn Im courious what the Buds show , if they are cured, and ready to be tested.

Flowering day 63 since time change to 12/12 h. Hey guys :-) The end has come 😍 Over the next 3-7 days the lady is placed in the darkroom for 48 hours before being harvested and hung upside down. The trichomes are checked every day to find the perfect time 👍 Watering was done twice this week with groundwater, each time with 1.2 l. Have fun with the update and stay healthy 🙏🏻💚 👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼 ‘Powered by GreenHouse Feeding’ Copy the link for 10% off all Nutrients 👇🏼 https://shop.greenhousefeeding.com/affiliate/MadeInGermany_PassionGrower 👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼👇🏼 You can buy this strain at : https://www.amsterdamgenetics.com/product/choco-cheesecake/ 👇🏼👇🏼👇🏼 Use the coupon code: madeingermany for 10% on all Amsterdam Genetics seeds Water 💧 💧💧 Osmosis water mixed with Cal/Mag (24 hours stale that the chlorine evaporates) to 290 ppm and Ph with Ph- to 5.8 - 6.4 MadeInGermany

I'm back and since the gorilla glues have been harvested this girl is taking her time and what a yield she's gonna give grandmommy purple

I harvested 24 cuttings from the White Shark mom this week, which was the first time she donated! She recovered fully within a few hours. Some ongoing maintenance pruning/training on deck for later this week. The 2 new moms (XXL & 8 Ball) are looking beautiful. I’ll be topping them soon to start working on structure.

Info: Unfortunately, I had to find out that my account is used for fake pages in social media. I am only active here on growdiaries. I am not on facebook instagram twitter etc All accounts except this one are fake. Have fun with the update. Flowering day 61 since time change to 12/12 h. Hey everyone ☺️. Today the time has finally come and the last week of flowering has begun 😍. She looks beautiful and her buds smell very tasty 👍. The trichomes are 70% milky and 30% amber. The lady comes in complete darkness for 48 hours before the harvest. Of course, as always, there will be a small interim update of the harvest before the last major update. Until then, I wish you all a lot of fun and stay healthy 👍🙏🏻 You can buy this Strain at : https://www.zamnesia.com/de/5165-zamnesia-seeds-kalini-asia-feminisiert.html Type: Kalini Asia ☝️🏼 Genetics: Black Domina x Purple Kush 👍 Vega lamp: 2 x Todogrow Led Quantum Board 100 W 💡 Bloom Lamp : 2 x Todogrow Led Cxb 3590 COB 3500 K 205W 💡💡☝️🏼 Soil : Canna Coco Professional + ☝️🏼 Fertilizer: Green House Powder Feeding ☝️🏼🌱 Water: Osmosis water mixed with normal water (24 hours stale that the chlorine evaporates) to 0.2 EC. Add Cal / Mag to 0.4 Ec Ph with Organic Ph - to 5.5 - 5.8 .

Hola que tal Growers!!! Esta semana empezó con un poco de preocupación por el problema del exceso del calcio el cual bloqueo otros nutrientes, !!!bueno eso espero!!!! hahahaha; pero va muy bien para ser mi primer cultivo Indoor, cambiamos el agua de riego por agua embotellada que tiene un PH= 6,9-7 y un EC=0,3 µs/cm bastante menor al agua de la red. Normalmente riego según la necesidad de la planta, siempre que veo el sustrato seco riego, el primer riego de esta semana solo agua aproximadamente 500ml para limpiar un poco la raíz de ese exceso. El siguiente riego si la alimento con aditivos universales de plagron, le va muy bien, la decoloración de las hojas no sigue, pero aún se notan en las fotos las pueden ver. Solución de riego PH=6,5 EC=0.8 µs/cm ( en la tabla de plagron me recomiendan llevarla a 1.7, pero quiero ir despacio para ver como reacciona, es más fácil corregir una deficiencia que un exceso si me pide más la planta se la suministraré)

My bag seed hermi managed to pollinate this plant some but nowhere near as bad as the plant I removed from the tent...valuable lesson learned this cycle and we got some cannabutter out of the deal..my cannabutter process here: https://www.youtube.com/watch?v=PAZOt4CukSc&

Already week 7, and it’s starting with much better air humidity which makes it easier for me to stay in the recommended VPD range – currently 54% at 25 °C at canopy height. With 58, 67, 78 and 80 cm plants’ average height is about 71 cm. Odour has increased, and sometimes, but only shortly, I get the feeling the coal before the blowers cannot eliminate all of it. While the smell was a bit strange sometimes one and a half week ago, it’s now absolutely yummy, sweet and promising. As is all the sticky stuff adhering to my folding rule when I measure their size. I am a bit confused about the amount of yellowing leaves. That would indicate a nutrition deficit. On the other hand, last feeding (yesterday it was only calmagged water) brought some brown edges to their tips as I wrote. Which could indicate a slight over-nutrition. I am not *that* worried as leaves around the buds all look great (except for mentioned, but not youngest tips), and mature plants obviously tend to concentrate on bud production solely. But week 7 is quite early, or isn’t it? Any recommendations? Maybe I should go with organic fertiliser next time to avoid being stuck between two options ;) As they had run dry already, I gave each one another round of drink. Slightly less fertilised than last week. And I removed the lowest yellow branches and tiny buds that would not make it into the light in time. The Pineapples must have some mimosa genes crossed in. Each time I touch them they bow away their heads in deep dislike. The taller one looks like her head would be too heavy now … It is not, and usually they recover after an hour or so. The Sherbets are pretty unimpressed by all I do. Meanwhile I’ve been working on the Raspberry Pi BoxControl that should help me stay in better VPD ranges in the future. I am not sure how to translate this all into a more stable solution than based on a breadboard, but the state so far (and how it is supposed to work): Raspi runs headless with control software on autostart. Every minute temperature and humidity are received from a GY-21 I2C chip that should be hanging around plant tops. Data is saved in a database, VPD is calculated and signalled in form of a RGB LED color. Additionally, LCD display rotates through current stats. 3 relay modules can en- or disable misting, dehydration or an additional blower. Maybe I can add a CO2 sensor just for the fun of it (but I’d have to develop a device protocol myself), maybe even one or two soil moisture sensors. Theoretically you could also have a lighting control, but then, GPIO ports are all used. The display needs a lot of them, and while I can log onto the Raspi on my local network and view its desktop, I’d prefer to have a quick overview at place. I am not really informed about current models. Are some GPIO extensions or Raspis with extended GPIOs on the market? But so far, that’s all theory. I never had a PCB developed for my hobbyist projects, I am not the best with a solder station. Never had a Raspi run 24/7 for a really long time. Did a bit more lollipop ping in the evening. Especially tallest Shepard had fun building some more very low buds and branches. I think it can investigate its powers better on different places. Day 51: It’s getting hard to measure soil humidity with my low tech device. Soil must be full with roots and I don’t want to hurt them much. I can see them at the outlets of their pots too, sometimes a bit dry of course as these parts run dry earliest. Experiments to include the CO2 sensor in my test setup failed. I can read and reset it, but setting measurement mode and reading values don’t work. Maybe because my I2C library cannot use ClockStretchLimit. Running out of GPIO ports anyway and seeing that the soil sensors are analogue devices, I’ll probably revive my Uno too and have discovered some clever Raspi heads that should make a more stable setup (and some cooling) possible while also adding a handful of PWM ports and an integrated display. I’d like to include a camera module too and it would be great to have some ports available. A final setup would obviously include a Raspi 4 or 5 to easily enable secure online access. But so far, all working nicely in test setup. Day 54: Sometimes I wonder if they’re still growing at all, but then it’s good to have the daily pictures to compare bud width which now seems to be the main interest of the ladies, although differences are now clearer to tell between two day intervals. The taller ones look like they are one week ahead of the smaller plants, with even higher fan leaves turning pale now. Which at an estimated seed–harvest time of 8–11 weeks for both strains should be pretty common, I guess. Or am I wrong? Summerly temperatures make the temperatures at canopy level sometimes reach 31 °C, but at least the simple ultrasonic diffusers arrived and I am getting closer to a better environment control. I can at least switch the diffuser inside the tent remotely from my phone, and a deep bowl of water with a lid so the "fountain" produced will not wet the tent floor and one of the fans placed at the bottom now to lift its mist upwards seems to do the trick. Humidity increases while temperature drops, getting the plants into a better VPD level, so all I have to do is wait for the evil A to deliver the necessary Raspi components to have this automated, maybe still while this grow runs. At the end of this week, there was just a bit of height gain for the two smaller ladies who now approach their next 10 cm mark. Overall, I get the feeling it won’t be that long until harvest. Maybe with the taller ones a week earlier than the others. There’s really not that much bud growth anymore, rather refinements – like buds getting more nodes and color. I’ll investigate the trichomes every few days but would welcome your estimation.

After 13 weeks of flowering, Lemon Cherry Gelato is finally ready. I haven't watered her for the last three days. Her buds are extremely sticky and shiny. 🍋🍒🍦

This plant literally outgrew a 4 by 4 at 87 inches tall I had the light at the top and quickly realized I had to toss her in the greenhouse about halfway through her life. Super happy with the size of it 43 inches tall exactly. Not sure if shes gonna stretch more but lmao the biggest auto I've ever grow. Mad respect to ILGM genetics right now. Check back next week to see how much her buds swell! Remember it's always 4:20 somewhere once an hour every hour!!!!!!

Another strong week here. The blumats are working well at this point so the girls get adequate water intake. She continues to fatten up, hairs ripen up. The trichomes are really building at this point. And the bud to leaf ratio is very good at this point. This whole run has a repeating theme, I need a cloner to keep some of these cuts

Lower leaves are losing color and browning, flushed out water and added fresh nutes in 4 days ago. Roots have a brown slug on them from left over nutes, probably going to rinse roots off in the next couple days.

12/06/2020 Start of week #3 in flower becoming a beast.

Last week of growing for the cheese 🧀 from our friends ganja seeds! For the moment the plant looks healthy! We did some defoliation on the bigger leaves and lower branches. Now only water until next week where we will apply some biobloom to the soil!