MATARO BLUE by KANNABIA WEEK #20 Overall Week #6 Flower This week was another good for this lady she's doing good her buds have a good aroma about them. Kannabia.com MATARO BLUE

Week 3: 2 are thriving 10" and 7", 1 slightly smaller 3", 1 quite small but healthy green and 1 sickly. light is now at full so I will wait while they grow into the light but may lower it depending on how they take the light. I will slowly bring it to 3'. Started the calmag and increasing nutes.

Hello and welcome to week 2 of veg phase for these five Epsilon F1 Hybrid ladies. Last week is now complete with daily updates and media so please check it out. For this week well frankly I am expecting massive growth. I have taken 3 fingered leaves from Normani today and five fingered from Ally. It takes more time to photo and diarise but it is rewarding to look back on! See you tomorrow! Day 9: Nothing to report. Sorry for lazy photos. Oh... I joined twitter @UnorthadoxDude Day 10: Fertigated 5l. Loving Ally's party hands 👈👉 Day 11: Normani has overtaken Ally as the tallest and largest plant. Dinah has overtaken Lauren in a similar fashion. All girls kooking good except for some odd marks here and there (see video). Today after the photos and video and when she was back in the tent. I took about 4 or 5 leaves off each girl. You'll see tomorrow. If you're here from Twitter, where I am also @UnorthadoxDude, please say hello in the comments! I've just joined and want to gauge if it is worth the time. Day 13: Heights: Ally 23cm Normani 28cm Lauren 24cm Dinah 19cm Camila 17cm The girls have begun stretching it seems. Day 14: Fertigated 5l and performed LST and defoliation. Normani height was 32cm. End of week summary: Huge week of growth and these ladies are only just getting started. The pheno difference of Dinah is stark but super interesting.

2 weeks of flowering are over and it Looks really nice:) Only Problem is the high humifity , sometimes its over 80%, so i ordered a dehumidifier which should arrive in monday, hopefully i get below 60% and i think i will do some defoliation next week

Plant 1 - 42 grams Plant 2 - 57 grams Plant 3 - 73 grams Plant 4 - 57 grams Total - 229 grams Not the best trim but I have been so busy and there was too many to trim. All in all nice grow.

Blütewoche 2 Die beiden Pflanzen zeigen keine Anzeichen von Mängeln oder sonstigen Problemen. So solls weitergehen. Pheno Nr.2 hängt weiter ein Paar Tage hinterher, macht sich dafür aber sehr gut.

🗓️ WEEK 5 / DAYS 29-35 (flo) 💧 There were no changes to the nutrient solution this week, maintaining EC 2.0 - pH 6. My main action has been topping up the reservoir with 5 LT of this solution every two days. 🌱 The stretching phase concluded this week, with the plant reaching her final height: 69 cm. She is now focusing on filling out her flowers, and her foliage is taking on a noticeably darker hue, typical for the later stages of flowering. At this point, there's less active work to do; the focus shifts to maintaining stable environmental parameters and ensuring the pH remains in the correct range to avoid stressing the plant.

AMAZING WEEK! The environment is reading for flowering. Lighting, feeding, watering, air temp and CO2 are all stable and should give my plants a stress free life. Humidity is still high, so I'll need to come up with a plan for dealing with that ASAP. I've introduced CO2 into the grow with my brand new AirBomz unit. It uses a light sensor that releases CO2 when the lights turn on, and then uses a timer to release every 2hrs until the light switch off. I doubt I'll reach the 1200PPM stated by the manufacturer, mainly because I'm running an extraction, but I figure some is better than none. Cool controller also included. After doing some reading I can see there's two things that I need to look out for: A) Switching off the extraction so it doesn't suck away the precious CO2 before the plants have had a chance to absorb it B) Making sure the room doesn't get too hot whilst the extraction is off, causing heat stress My solution is: A) Switch off extraction for 15mins at the AirBomz 2hr interval B) Use the Temp Controller the switch off the circulation fan when temp exceeds 27C C) Controller then switches on the active intake when temp exceeds 28C D) Temp is held at 29C whilst the extraction is off D) Extraction turns back on after 15 mins, temp drops below 27C E) Temp controller switches off active intake... F) ...And switches on the circulation fan G) Repeats every 2hrs NEXT WEEK: Work out how much the girls are drinking! I'll know when I change the reservoir.

I used nature's living soil and PH water only, she came out smaller than I expected but was still a lot of fun to grow and I learned quite a lot.

Did some LST... I did a small mistake with not filling the pot all the way...

Hello, fin de semaine 10, floraison 4. Les plantes n’ont eu aucuns problèmes pour récupérer de leurs défoliation de la semaine précédente. Elles semblent en parfaite santé et la croissance des buds commence à se matérialiser de plus en plus,,, 😁 J’ai légèrement ajusté l’hydrométrie vers les 45/50%. J’ai aussi fait un arrosage plus léger en milieu de semaine à l’eau sans engrais avec un simple pH ajusté à 6.3/6.5 L’apparition de cristaux commence à se voir. C’est beaucoup plus marqué sur la gorilla CBD que sur la critical+ 2.0. Voilà,, c’est tout pour cette semaine.. Happy grow...😎

Soo the last gg4 sherbert died so this is a new sprout that is about 4 days old.. doing just fine.. follow along guys thabks alot !!! Here's my YouTube https://youtube.com/@thedankzz420?si=13j0h50b5hz6riL9 I think I will cross this with a biscotti.. lmk what you think !!! See yall in berlin!! Thbaks alot!!

STRAWBERRY PIE AUTOFLOWER (FASTBUDS) SOLO CUP GROW WEEK 10 She is nearing the end. Trichomes are mostly cloudy with some amber here and there. Likely give her another day or two before the chop.

Después de un arduo trabajo estamos en la última semana de fertilización

Chop Day! After recovering, i noticed she had the leaves closest to the fan drying up. I think since she lost most of her leaves, it was too windy and she got windburned. Considering her over all bad shape i decided to go for an earlyer chop then usual, but all trichomes seem to be milky, with just a few brown ones. Over all, this grow was filled with problems and fuckups. Many things were learned :) May the next one be better!

Hey everyone, All the buds have been sent to my cozy basement for curing. I cure the dried plants in glass jars, burping them periodically. I maintain a temperature of around 20°C (68°F). This process takes anywhere from 2 to 6 months. I do all this to ensure a smooth and enjoyable experience later on. For consumption, I use my Xmax V3 Pro vaporizer. Cheers, see you all next time!

Day 78 - I swear the Orchid is getting skunkier by the day. First thing I smell when opening the tent. Added some pics with a selfie seeds sticker to show the size None of the strains here are Selfie Seeds, sticker was used for showing the bud size. Day 81 - I'm so ready to smoke these plants. The Apple Banana Zoap smells just like the flower I ordered from LIT and it's sticky as hell so I know they're going to be fire even though they hermed. I removed a couple more nanners found lower on the branches that I couldn't see for ABZ#2, NO MORE found on ABZ#1 as of now... Checked PPFD again today: ABZ #1 - 810 PPFD | ABZ #2 - 875 PPFD | Biscotti - 750 PPFD | Black Orchid - 1040 PPFD Day 82 - Used the jewelers loupe and camera to compare for trichome quality against the microscope Day 83 - Noticing reduction in feeding consumption all around. ABZ 1: 0.9L | ABZ 2: 1.5L | Biscotti: 1L | Black Orchid: 2.0L Biscotti is giving a vanilla and lemon terp profile with the pine spice in the background now. It's nice tbh Day 84 - This is the last day of week 7 since flip, week 8 starts Tomorrow. I'll be dialing back my light a bit and the ppm. Pulled the ppm back a bit tonight as I've still seen issues with the nitrogen. Feed tonight was 926PPM. Might have a new nutrient mix to use on them Wednesday.... I can't get better pics with the microscope sorry, I'm too unsteady for that. (Maybe cause I turned the LED down on the microscope)