Aparecieron unas pequeñas manchitas en las hojas más viejas, se realizó el trasplante a maceta de 5 lts y se regaron foliarmente con Knactive por estas hojas amarillas que comenzaron a salir y para que tomaran de buena manera el trasplante. Seguimos ... Pronto se viene la floración

Good week but I don’t think 😬Im getting any pollen this run. I think the silver in old. I don’t know but the plants no pollen. Jelly cake is a cross breed of wedding cake (mother) grape ape auto (father)

What up fam, weekly update on these lovely ladies. I put the scrog net out this week for support and am I glad I did. Only after a couple days they grew right through it. The greenhouse is 6'5 feet tall and they're pushing 5'6. I'll go in there and take off some of the lower fan leafs at the bottom but not to much defoliation needed. I'm seeing preflowers so I'll also switch the nutes from grow to bloom. All in all Happy Growing.

Seeds were placed in a glass of warm water for 72hrs in a dark room. Thursday’s seem to be the lucky day for planting. I placed all three seeds in loose soil… sprout loading.🌱

;)

The plants were so crowded I decided to put them into a Larger tent to allow some light to the lower bud sites and to help lower the humidity amongst the plants. I'm sure they will love the extra space. The light has now been raised 20cm (20cm taller tent) Allowing me to turn out right up which is 45000 lux in the centre right below it. I will up the bloom to 2ml/l this coming week.

Very strong plant 💪 Bravo Inseedious👏

The flowering is starting to become noticeable. At first, all the pistils have developed well. It's clear that the plant is drinking a lot more, although the soil takes a bit longer to dry out, so it stays somewhat damp. I’ll do a leaf pruning, removing one leaf per node.

Buds werden immer dicker, Klebriger und süßer im Geruch Cold Flush wird anfang nächster Woche einmal durchgeführt

Commencing Day 36/Week 6 on November 28th D36 Still slow and steady growing. Some much more slow and steady than others. I am hoping by the end of this week or by sometime next week I can flip to 12/12 and get cuttings. My goal is medium/small size plants with medium sized yields and to hopefully 🤞 find at least one keeper of the bunch. Reason being I have a lot going on and want to see whats the best I can get with light work load. Bigger plants=bigger work loads. I also noticed the Boss Hogg1 must be Canadian 😄 one of the leafs is a maple leaf shape with no finger separation (aka duck foot mutation 🦆; see photo). This is the same plant I called a Purple Tarantula in one of the earlier weeks. Definitely a freak. Day37 Filled all buckets till water line was bubbling into net pot. Filled with oxygenated &(dechlorinated) house water. Added 10ml Clonex per bucket. Some needed pH but not much on .2 off from 5.8. ppm is around 800-900. Leaving lights on again overnight. (Cold front coming). Day 38 Added 5ml Cal Mag to each bucket. Added more fresh water to bring PPM back down to 800. pH sitting around 5.9 Noticed 818 Headband was hiding a tiny clover friend. I'll keep it there for now. Maybe find a four leafed clover for good luck 🤞 Also noticed that the sativas phenos are being picky eaters compared to the rest. Also noticed the 818 is catching up a little more. Definitely a nice healthy steady growth. Just quite a bit slower then the Gorilla Zkittles. Lastly tonight the plants will go into 14 on 10 off. This is to induce stretching (they are sooooooooo short; due to 8 on 4 off light schedule) and maybe preflowering also. Won't be long!😄👍 Day 42 Few days in the new light shedule is working great. Plants seem to be getting ready for me 👍 I've also switched the plants around to accommodate the grow a little better (ie in order of size) The 818's and Raspberry is catching up slowly to the GZ giants. (& looking great 😄) but man these GZs are thirsty girls, they drink the ppm and water levels in one day what the others take in 3 or 4. Needless to say I've been pHing everyday basically and adding water and light nutes to keep around 800ppm and 5.8pH. maybe only mentionable is that the GZs needed more nutes (ppms dropped about 200ppm to 600 in two days) and pH balancing (pH shot up to 6.2 in two days) than the others. I'm getting anxious to flip and cut. The GZs are right where I want them. The others, not yet. I'll have to find a happy medium where the runts are at least so big with out letting the GZs get too big. Thank you for reading and watching

Sep 13: took a second round of buds. Have now taken off 2 kg of wet buds with 1 kg fresh frozen and 1 kg done as ice water hash. This is equivalent to 500 g dry bids already taken off of this plant with another big chunk still to go. Very nice hard buds off of this plant. Sep 19: the remaining lower buds turned purple last night and look great. Will harvest the rest of it tomorrow morning.

7/28/19 --Super happy to see the plants doing this well. Ive found that every other day feeding is the best for these specific plants. Im a big proponent of only watering the plant when it signals it is ready for watering. The least possible amount of induced stress for these plants is the goal for me. Cheese seemed to be totally unaware of the FIM that was done on it, as it showed not even 1 sign of stress post FIM. Cream cookies is another story, she's quite sensitive to absolutely everything--including watering. I am super happy to see that the last fan leave on the 5th node has 9 leaves--a really good sign that the plant is doing extremely well. The more leave nodes on each leave the healthier than plant. There are zero signs of nutrient burn at all. It was difficult at first to see if the slight bending of the leaves was due to nutrient burn, but I later figured out that the leaves were pressing against the side of their pot and as a result bending--wasnt nutrient burn. Ive been varying the pH widely each week--with the attempt to be as random as possible. I want to make as many nutrients available to the plant as absolutely possible. I really am loving the Advanced Nutrients Sensi line. Im growing in coco but I bought the nutrient mix not designed for coco with the understanding there might be some potassium issues down the road. But otherwise as a chemist by profession, when I heard about the pH perfect line I was rightly skeptical. It will balance your solution to the correct pH range (5.6-6) IF you start with dead neutral pH 7.00±0.05 water with no dissolved salts (distilled water). the distilled water I've been buying (from Walmart) clocks in on the pH meter at around 7.6-8.6 which will cause the pH perfect technology to neutralize some of the dissolved ionic species and bring the pH well below safe range for cannabis. Ive found that if you pH the distilled water to 7.00--add your Ca/Mg/Fe, THEN add the pH perfect technology the range will be much more suitable. It was kind of annoying since my pH down is so much more concentrated than my pH up. Me problems I know but still annoying. --One of my amazing collages at work is going to water both babies today with Week 4 nutrient solution even though we are technically in week 5. My vacation has prevented me from mixing the solution to feed. --This vacation has brought so many new automation ideas to coco coir growing. Ive been developing a hypothesis that involves what I call the "level of droop age" and its correlation to plant thirst. It began when I was growing in soil and needed a better way of telling when to feed the plants instead of a fixed schedule, which seemed to be giving way too much water to the plants. ---Ive developed a "droop scale" which can be directly correlated to plant thirst. Ive also found that very happy plants that do not want water will go through a natural droop cycle as night approaches. I take this as the plants time to grow out its root system (happens at night). By the morning the leaves are pointing up in what I call "leaves up loving life" ---So the scale I've developed is kind of arbitrary but it does a really good job imo if you become very familiar with your plants. ---The scale ranges from -10 (the most droop in the leaves every observed) to +10 (the most extreme leaves up loving life ever observed). the scale is out of 10 not 20. ---lets say that you watered your plants today, and their leaves were at a -7/10 droop (what when I water my plants). If you water them you should observe no increase in droop--in other words after watering the droop should only improve not regress. If the droop increases after watering your plants wanted a little more time before their feed--so alter your droop scale until you find the level of droop that when feed causes only an increase in the droop. 6 hours after watering you plant droop should be >+1/10. The next day you should see your plants at least at +5/10 droop. ---Merging this scale with automation is going to be difficult as ill have to use an open source machine learning AI to learn when the plants droop is sufficient enough to justify a watering. I hope to set up the system to be automated or manually operated over the cloud. ---Using a Raspberry pi and an Arduino as well as a whole set of motor control boards and sensor boards I hope to put together an integrated system that can detect when the leave droop reaches critical levels using a camera, and feed accordingly. Ive been all over the internet and all automated grow projects rely on soil moisture sensors which only penetrate <4 inches into the substrate. This doesn't cut it for me as the root ball of the plant is way below that 4 inches of the sensor, yielding readings which only pertain to the top layer of soil, which just so happens to dry out the fastest. ---Im going to keep my grows at 2 plants each from no on--and I plan to make an automated system for both plants which can control watering to both plants individually. Im currently trying to figure out the best way to track volume of water dispensed. A flow meter with a know diameter tubing and a known diaphragm pump rate seems to introduce all sorts of inaccuracies into the mix. I think im going to design an automated measuring system that uses an ultrasonic distance sensor coupled with a camera and AI to fill up a the hopper to the desired volume of nutrient solution. ---I have all the hardware listed but im a complete dumbass when it comes to coding. My profession is chemistry, coding goes right over my head. I have an immense respect for coders as I honestly have no idea how you guys do it. Its like learning 15 different languages at once and using them all together. Blows my the ability of our society. The wide range of skills. Love it. ---If anybody would like to help me code this project it would be greatly appreciated. 7/30/19 -Cream Cookies is doing extremely well. FIM was a great idea. 4 new main cola sites came out of the FIM which im very happy about. The undergrowth also has caught up to the canopy. the canopy has a plethora of bud sites. Defoliation done to increase light to bottom branches. Largest fan leaves towards the canopy removed. FIM'ed leaves that opened up also trimmed, allowing more light to penetrate to those small bud sites. --Ive counted sites where main colas can form. Very happy with this HST I decided to do. --LST done and branches separated from each other so they can receive ample light. Thinking of adding supplementary 40W flowering bulbs for flowering. -Cheese FIM didn't work as intended but it did break the symmetry of the plant. One of the first branches has grown higher than the canopy and I had to tie it down using LST. Did some defoliation and going to do some LST later. --Some light stress spots on Cheese, makes sense since I wasn't physically at my apartment to raise the lamp. Before raising the lamp the plants were 14 inches from the light which is way too close. The closest it should be is 17 inches. Raised the lamp to 18 inches and spots are subsiding. --Being overly cautious ive increased the dose of Ca/Mg/Fe to 4 mL/gal incase spots are actually a Ca/Mg/Fe deficiency from explosive growth. 7/31/19 -Cream Cookies is showing beautiful pre flowers. Still recovering from light stress. Looks very similar to nutrient burn but only present in tip most growth suggesting light burn. 14 inches was way too close-vacation problems lmfao -defoliation done on both cheese and cream cookies to expose bud sites -LST done on both cheese and cream cookies to bring bud sites into the light -both plants fed 400 mL Week 5 nutrient solution-when I mix next weeks nutrient solution im going to reduce the concentration to 12mL/gal w/ 3mL/gal Ca/Mg/Fe. --I want to precent any nutrient burn plus plants are slightly stressed from defoliation and light burn from my vacation. -lamp raised to 19 inches to help aid in stress relief -plants are responding in a weird way to the watering. Not in a bad way-but in a different way--larger lower leaves are not drooping like in the past its just the much newer growth is drooping. Makes sense since newer growth has less developed support system. Makes me feel much better about my watering schedule. --Clawing which I suspected was due to light stress is getting better-especially after a feeding. 8/1/19 --Calcium deficiency just barely showing on midlevel fan leaves. Good thing calcium is a mobile nutrient. Going to readjust the nutrient solution ph to be 6.2-6.3. Been accidentally locking out calcium. --Defoliation done on both plants to expose more bud sites and to thin out the thick canopy so light can penetrate below. The hope is to defoliate correctly. If done right I won't have to lollipop. --Cheese has no preflowers yet--still in veg --Cream cookies looks like it started flowering. 2 preflowers were spotted earlier in the week. Surprised to see how fast the plant moved into flowering. Going to be feeding it with flower nutrients starting week 6. --Going to continue feeding cheese with veg solution until preflowers are observed.

As you can see from the third picture on day 29 she is looking a little ugly and unkept. I'm not sure if this is a normal thing or something I need to take action on. Advice would be great. So day 30 rolling around. Decided I had to try LST again. She felt more receptive to being bent over today as well. I mainly had to attempt it for space reasons. With the current covid panic all the markets where I buy my buckets from are closed and I can't procure a new one to increase my height for probably a couple of weeks at this rate so LST was my only option. She seems to have taken well to it and I will upload a finished picture of her shortly. Day 32, watered and fed her. 500ml of water plus .3ml each of fox farm trio. Hoping to see her perk up a bit. Concerned about the large brown spot on one of her leaves which made me think she was having a deficiency? Probably a bit early to worry about buds fattening up also but I am worried they are looking a bit airy at the moment on the non main cola sites. I'm not sure if my LST was effective at tricking her into trying to have more than one top cola? Day 33. No noticeable gains today, at least to my eyes. I can spot a little nute burn perhaps but hopefully nothing too serious. Looks like a cola that isn't the original top is starting to fill out just as much, if not more, than the original top though. Hoping they all catch up at a similar pace to each other and reduce the pop corn nug potential! Day 35. She has shown a few more bud sites since last post. I am worried that she is going to produce a fair bit of larf/popcorn bud and wanted to know how to get rid of that? I am not confident to remove any growth without knowing for sure it has a beneficial impact on the overall health of the plant and the final results. Any advise is appreciated. She also seemed a bit thirsty to me. The leaves were feeling a bit thin and dry so I gave her 1L of water with .7ml each of fox farm trio. Hopefully she responds well. I will check her in an hour or so to see if the leaves are starting to point back up - fingers crossed.

Hello everyone week 8 has passed ☀️ They are very well growing at fast pace and with a beautiful green colour on the leaves🤩a lot of buds everywhere🍋 The weather is perfect this year a lot of sun,not too High temperature and the humidity around 50%😎 Some defoliation just 2-3 leaves max to let the sun penetrate the lower buds✂️ Homemade nutrient 100% bio🍌 I force the plants to flower in my garage 100% lightproof😎 So every morning and every night i remove all the plants from my garage at the same hours 💪 See you next week 🤩

F week 1.

Day 39-02/09/22 so I’m trying to get back on track with the diaries!!! Today gave them a nice liter of water with grow/bloom/topmax the 3 of them very in size about 35cm 40cm and the tallest 45cm so far so good

Commencing Week 7: day 43 on January 12th Today I left the dirty girls (I call them that because they are in soil 😋) out of the tent for their first time in their lives to hang out with some new girlfriends (my photoperiod s). They seem very happy to be hanging out with them 👍👍 The other day I took one of my personal photoperiod Crosses and pollinated one of the bottom flowers of the bloody skunk, hopefully seeds will be coming soon :-) Today I started thinking about how much longer they have left and it seems the bloody skunk is nearing the finish Line already. In the beginning of this diary I wanted to achieve the goal of getting some autoflower seeds by taking one of the syrup strains and cross breeding it but none of my syrups strains made it from seed for some reason. So now I'm thinking about taking the top bud off of bloody skunk in the next week or two and letting the rest of the plant go through rodelization so I may still achieve that goal. We shall see. Thanks for the great genetics everyone attention and support. Won't be long now till I actually get to do a harvest report 😎👍

Day 56 of flowering of the 2 Hyper Glue from Anesia Seeds Getting to the end of the line of this beautiful 2 plants she frosty she smells absolutely amazing she flushing very good and is almost done but here leaves are still Green en very healthy looking 🤔 here leaves should be turning other colors because of getting the feed out of the soil ore i am i wrong and can the nutrients be flush out but leaves still very healthy looking ? Trichomes are looking good how i want them so i am bit confused with this one but if the ppm is down enough i might just cut here down because she is looking fucking great 👌🏻 23/12/21 Runoff is around 1100 ppm almost done 👌🏻 25/12/21 Runoff is around 800 ppm I will be now drying the pots out and then it's chop time for these 2 26/12/21 Day 58 flowering runoff 600 ppm 🤘🏻 beyond frosty buds are HUGE!!! smell is Tru the roof Super Glue x Apple Fritter is something els thricome are where i want them and has a day to go to dry out the soil and then light's out for 24 hours it was a perfect grow From beginning to end can recommend any grower Hyper Glue from @anesiaseeds 28/12/21 Chop chop 1 hyper glue One left to chop good times Happy holidays people hope you have some great days stay healthy take care of the one's around yeah and let next year be more weed and Less fucking corona so i can get my ass to Alberta Canada for month vacation to see if we could move there 🤘🏻🇨🇦🤘🏻 visit www.marshydro.eu for your best gear and use the PROMO CODE: DEVILSBUD Some info about the Marshydro FC-4800 Superb Quality LED Chips: The whole light is composed of 1206 pcs Samsung lm301b and Osram 660nm chips. More than two times as many LEDs are used to drive the grow lights at low currents and to avoid overdrive. Quality is guaranteed and efficiency is up to 2.8 μmol/j. Even PAR Distribution and High PPFD Output: The multi-light bar design and the densely distributed light chips enable the LED grow lights to achieve the optimum PPFD required for plant growth over the entire effective coverage area. Specifically Designed Spectrum: To ensure even plant growth, blue and red light are enhanced on the basis of a full spectrum combination. Not only does this accelerate plant growth, but it also improves the yield and quality of the plants at the same time. Dimming Daisy Chain Function: The dimming function saves on electricity costs and enables brightness from 10% to 100% for the different stages of plant growth. A single master light can connect up to 30 lights in a daisy-chain system. Business LED Grow Light: The light's wavy heat sink dissipates heat quickly and the IP65 waterproof allows the light to operate in humid conditions. 180° collapsible feature for easier installation. All these features provide favorable assistance for commercial cultivation. And some tent info ●【Lock All Light Insid】MARS HYDRO Grow Tent Interior is made of diamond mylar. Non-toxic to the environment, no harm to plants. High-quality 1680D canvas being double stitched, (ALL OTHERS BRAND grow tent is 601D canvas) which is tear-proof for perfect light locking, No light leaks or rips at all. ●【Durability Grow Tent】Stable Metal corner adapters and poles are the trustful supporters of the tent. No rusting nor paint-falling. Quick easy tool-free installation. Carries strong heavy-duty SBS zippers, double layer lining to create a light-proof seal. ●【Easy Observation of your Plants】Special peeks window made by double layers of cloths. Observe the growing conditions of your plants without opening the tent and avoid disturbing plants. The peek window also serves to dissipate heat and ventilate air. ●【Removable Tray Keep Clean】The package includes a removable waterproof floor tray to hold soil and fallen leaves. The tray can be taken out easily to wash. Removable and water-proof makes cleaning easy. ●【Good Ventilation&Fast Assembly】 Circular double-sleeved vent holes with adjustable nylon strap for air circulation by exhaust fan, ducting, carbon filter, or reflector. Better allows proper light, heat, and airflow. Quick tool-free installation. Reinforced by a sturdy metal frame to ensure security and stability, supports up to 140lb. Perfectly safeguard your plants to thrive even in winter

Got the last trimming may need second trellis