By continuing to use the website or clicking Accept you consent to our cookies and personal data policy and confirm that you are at least 18 year old. For details please see Privacy Policy and Terms
I attended NECANN (New England Cannabis Convention) in Burlington, VT this weekend - Great event!! While I was there I purchased these two Baox hemp clones. The baox strain is supposed to have very high CBD content with very low THC (less than 0.3%). I have obtained a hemp farming license from the state department of agriculture. I will be expanding my grow room setup over the next few weeks and adding a separate flowering tent for photo period plants, including these hemp plants. I am hoping to learn a lot about CBD here. My family has been using a variety of CBD products recently and enjoying the results. Hopefully I will be able to make some of these products on my own in the future. 👍
Baox got a transplant this week. Gave them just a little Recharge this week, I'll be increasing the dosage next week. So far they are both looking like happy and healthy little girls. 👍
Baox coming along nicely after the transplant to a bigger pot. I'm planning on moving these girls outside in the next week or so, then I expect them to take off!!! 👍
Boax plants coning along strong. Grew about 2 inches this week. One plant is 19 inches, the other is 17 inches, I averaged the height as 18 inches for this weeks update. I'm going to take cuttings for clones from these girls soon. If you check the pics you should see that the taller of the 2 plants has a "Y" where the main stem split for some reason. I'm thinking cutting at the bottom of the Y would give me a good cutting/clone. But I'm open to any other advice/input on taking cuttings and cloning. I've done it once before successfully, but I'm no expert. Thanks all!
I'm going to take cuttings for clones soon. If you check the pics you should see that the taller of the 2 plants has a "Y" where the main stem split. I'm thinking cutting at the bottom of the Y would give me a good cutting/clone. Any thoughts or advice welcome... Thanks!
Hey dude, sure you wouldn’t have a problem cloning but I think under the V may be a bit too big... as you need to cut 45• at the next branch below the V. Could work, you would be better using that V as 2 clones and cutting just above the V lots of Hormones already present in that section due to the prior topping! Good luck✌️🏻
Baox plants got topped last week for clone cuttings, so they lost a few inches. I got 5 clones out of the 2 plants. I probably could have cut more, but lets see how these first few turn out first. These girls seem fine since the cuttings.
Hello GrowDiaries Friends,
Unfortunately I was in a car accident last week. I shattered my heal bone (calcaneus), fractured my face and tore open the side of my face around my eye. I’ve had a few surgeries to put things back in place and I’m feeling better each day.
However, my injuries prevent me from caring for my plants personally. One of my best friends (who is also a grower) has been helping with feeding the girls and my wife has been pitching in with waterings also. All of my plants are still doing well, but its too much to ask for them to take pics and videos as I would normally do to update my diaries.
I’ll be off my feet for at least 2 months, but I do plan on updating my diaries as I can. Which will probably be mostly harvest reports. I’ll miss taking care of my plants and doing more GD updates for now, but I’ll be back!!!
OK, its not exactly week 7, but I've lost track of how many weeks I missed due to the accident. I'm finally able to hobble out to the outdoor garden and get some pics to update the diary. I'm adding a 3rd plant because all but one clone died, so I'm including that surviving clone here.
I didn't get these girls outside as early in the summer as I wanted. They didn't get outside until late July. So they are much smaller than I was hoping for. But they are starting to show bud sites. I think I'll still have a decent enough harvest to make a bunch of CBD capsules.
You can see in the pics we cleaned up a bunch of weeds from the garden area and reorganized the plants. Looks much nicer now IMO. 😃
I'd also like to say THANK YOU to all of the support from the GD family. It means a lot! 👍
Baox starting to show small bud sites. And they have grown a bit since last week. I wish I was able to get these plants outside sooner, as I'm sure they would have grown larger. But I'm sure I'll still get enough hemp to make a few batches of CBD capsules. 👍
Buds are starting to really develop now. Leaves are starting to yellow also, they can tell harvest is coming up. I'm hoping they will be done by mid-October - that's typically when we get our first winter frost here in VT.
Moved these girls back inside this weekend. I started to see what looked like the start of bud rot outside. Its been cool and damp for the past couple of weeks and bud rot loves that. I cut off a couple of branches which showed signs so I would not bring any indoors (fingers crossed). I'm going to chop and dry 2 of the plants this week - once I'm sure there are not anymore signs of rot. The third plant still needs another week or two. The video shows my upcoming grows also. New diaries coming soon! 👍
Getting close to the end here. The good news is there are no new signs of bud rot, yay! I'll start chopping the first 2 down this weekend and cut down the 3rd in another week.
I plan on making CBD capsules with these girls. Any comments or advice on the best process for making capsules would be appreciated! 🙏
Cut these girls down a couple of days ago. They are hanging and drying at the moment. They look and smell really nice! I'll post the harvest report once they have finished drying. 👍
Looking forward to making CBD oils and capsules with the harvest. If any one has any favorite recipes or methods please let me know. These girls are sweet and sticky, they should make nice oils & capsules.
Looking for good recipes/methods for making CBD Oils and Capsules. Any tips or advice would be appreciated. Anyone using a Herbal Infuser? Do you think its a good idea to decarboxylate? Any recommended base oils or empty capsules? Looking for as much feedback as possible. Thanks
Nice easy topical and baking oil recipe.
7-10 grams of ground, dried cannabis
1 ½ cups of coconut oil
1/3 cup olive oil (optional)
1/3 cup beeswax
1 baking sheet
1 saucepan (or double boiler)
1 jar
1 saucepan (or double boiler)
1 jar
1 cheesecloth
A few drops of essential oil (your choice)
Heat, weed to 240 in over for 20mon.
Then transfer weed up to.stove pot pot and cook low and slow mixing coco with it in a pot for 29-25 minutes
Then strain through the cheese cloth, into a jar or another container and set it aside. (This can be dropped straight in mouth, baked, or cooked with) *careful of the intensity.
*that coco oil is suitable for making treats, its only once you adding the beeswax and essential oils that it turns from edible to topical.
Ive done this whole.process in a crockpot, as that generate just enough heat but not scorching hot.
If you own an instant pot pressure cooker those work good too but watch out for high heat settings, or bye bye thc. ✌️💚
DudeGrowsWeed
