The Grow Awards 2026 🏆
Likes
Comments
Share
@NO_DRAMA
Follow
U can see everything on pictures 💪 Ready for Harvest !!!! 💪
Likes
57
Share
It's finally here 😀. Both phenotypes are in the fermentation phase 😍. The grow was a lot of fun, so I thought I'd make an Iolator hash out of leaves and a little bud and a little oil out of both phenotype buds. Cannabis: The grow: Both grew beautifully. Your stretch was normal and it didn't cause any problems. Feeding : You received GHSC bio Grow once in the vegi phase and GHSC Bio bloom twice in the flowering phase. GHSC enhancers were added every 2 weeks. That was just the right amount for both : 1:. Optic: The appearance of Phenotype 1 is almost completely purple 😍. Pheno 2 is coated a bit purple with a mixture of silver from the resin :-). Smell / taste Pheno 1 tastes very fruity. You can really say that it tastes like a tangerine in the finish : 1:. Pheno 2 also tastes a little fruity but with its distinctly stronger note in the Kush direction. Both very tasty : 1:. Storage: The cannabis is stored in glasses in a dark place where the temperature is between 19-22 degrees. The first 2 months of fermentation are boveda packs 62% in the jars. Then the 58% come in. Since I was in the mood for a few specialties again, as mentioned above, I also made Hash Oil and Ice Oilator hash. Let's start with Video 1 (BHO) Hash Oil production: Hash Oil: Process: Small grated cannabis goes into the Dexso tube. Below is a container in the PTFE film that serves as a base so that the oil can be easily removed at the end. At the top we give the Dexso gas through the Dexso tube filled with cannabis. The result is a mixture of the gas and the cannabis oil. We put the bowl with the mixture in a hot shot of water but make sure that no water comes in at the top. We let the whole thing simmer for 20 minutes so that the first gases can evaporate. Then everything goes into the vacuum chamber so that all remaining vapors can really escape and we have a pure product 😁. The whole thing is carried out for 2-3 days until the oil is ready 😀. I can only recommend everyone to vaporize oil in a dabbing rig 😍. Taste: The taste is extremely delicious. In the finish, it tastes much more like mandarin than the buds 😀. Optic: The oil is very shiny to matt. If you pull it apart, it becomes light as honey :-). If you roll it up, it's very conceit. Consistency: The oil will become a little harder in the silicone storage after a short time. However, if you take it in your hand, it can be pulled and kneaded very easily after a few seconds. That was it with the oil production. So let's continue with the Ice o Lator 😀. Making the Ice o Lator: I took all the remains of the leaves and placed them in the small net. Then the IO maker is first made about 1/3 full of cold water with water. I add 3-4 kg of ice cubes and wait about 15 minutes until the water is below 0 degrees. As soon as the temperature is reached, I put in the net with the leftovers and set the timer to 15 / on and 10 / off. I run the whole thing 3 times. Then the complete broth is passed through the sieves (160, 120, 73 and 25) in a bucket. After sifting everything is spread out on a ceramic plate and poked very small with a knife. The whole thing comes in a dark place and is then allowed to dry for about 3-4 days. As soon as the hash has dried, it comes into the press for a few hours at a little temperature. The result is a kneading oily Ice o Lator 😍😍😍. Optic: The optic is partly reminiscent of that of oil :-). Consistency: The ice o lator has a very soft consistency :-). You can roll up small sausages while smoking 😁. Taste: The taste is very medicinal. But very earthy and smoky finish : 1:. All the screenings are very good but the 25 and 73 are the best 😃. That was it with the production to see everything again in Video 2. So we come to the end of a beautiful passage ☺️. Finally, I would like to say that I would like to thank Sweet Seeds for the sponsorship and for providing two such great genetics 🙏🏻. If anyone has any questions about this type, oil or ice, I will answer as soon as I can. I wish you all a lot of fun with this big update :-). Have a nice start to you and your families into the new year and everyone stays healthy 🙏🏻. Let it grow 🍀 MadeInGermany You can buy this Strain at : https://sweetseeds.es/de/red-mandarine-f1-fast-version/ Type: Red Mandarine F1 Fast Version ☝️🏼 Genetics: Red Poison Auto®️ (SWS39) X Tangie (California Orange x Hybrid Skunk) : 1: Vega lamp: 2 x Todogrow Led Quantum Board 100 W 💡 Bloom Lamp : 2 x Todogrow Led Cxb 3590 COB 3500 K 205W 💡💡☝️🏼 Soil : Canna Coco Professional ☝️🏼 Fertilizer: Green House Powder Feeding ☝️🏼🌱 Water: Osmosis water mixed with normal water (24 hours stale that the chlorine evaporates) to 0.2 EC. Add Cal / Mag to 0.4 Ec Ph with Organic Ph - to 5.5 - 5.8 .
Likes
14
Share
@GRow_M8s
Follow
⚠️ We keep pushing the plants with 24/24h light schedule + increase nuts gradually. ℹ️ Crystal meths (3p) and fast berries (3p) are the tallests plants in the tent, we decide to experiment with the Crystals so we will make, #1 topping (tallest plant), #2 supercroping and #3 nothing. ℹ️ Girls scout cookies (2p) are the only plants in the tent that haven't trichomes yet (bloom) 😪. - 38 till 🔚 -
Processing
Likes
7
Share
Likes
2
Share
Skywalker rounding the corner. Harvested 8/7 @ Day 76 from sprout Blueberry bulking up. Glueberry og done stretching and bulking up now
Likes
24
Share
@Kirsten
Follow
14.1.25: I've been readjusting the LST. I just took all the pegs out and reshaped her. I got some new LST equipment in the mail today, have been glad to have more pegs. I got some clips too, but they don't seem to stay on 😕 I'm currently only using the pegs, I have some thicker soft wire, but I forgot I don't have pliers to cut it! Also I'm running very low on Biobizz nutrients, so that could be bad 🤞 18.1.25: I have done another large defoliation on PPP1 and PPP2. Also, moderate defoliation on all other plants today. All LST ties and pegs are readjusted. I have turned up the light to 90%. Same distance of between 24-28 inches, depending on height of specific plant. I have increased the dosage of Biobizz Bio-Grow and Fish Mix to give an extra boost of Nitrogen as several plants were showing yellowing. They have responded very well to this. Unfortunately I ran out of my Biobizz nutrients and PH UP. I'm currently using Bicarbonate of Soda to increase the PH after the nutes PH comes out to about 4.1. Obviously, that uses a lot and I only had a 250ml bottle, which I used last run too. This run I have 9 plants. The only thing I'm worried about is the salt build up. Have you used it before? Or any other natural way to increase PH? Please let me know! I've also added Biobizz Fish Mix to help with the extra Nitrogen needed. Watering with 1ltr of dechlorinated water PH'd to 6.3 with the following nutrients;- ♡ 4ml Biobizz Fish Mix ♡ 4ml Biobizz Bio-Grow ♡ 2ml Biobizz Bloom ♡ 2ml Biobizz Top Max ♡ 2ml Cal-Mag ♡ 2ml Ecothrive Flourish. I water with this every 3 days. I did order some more Biobizz Bio-Grow and Bio Bloom. I found some at a reasonable price on Amazon. I still have about 800 ml of Biobizz Fish Mix left, too. It is fairly expensive this time as the plants are hungrier this run. I also got a new bag of Canna coco, which I may use to add a top dress with some dry amendments. Which hopefully will save some cash on the bottled nutrients and stretch out until the end of this run without having to buy anymore. I have purchased a funnel to pour the water. It is difficult, due to the shape of my LST, to water precisely. I have spilt it all over the tent several times 🙄 I've also ordered a 2 litre jug. Currently, I'm mixing water for 9 plants individually in a 1 litre jug. It's tideous. Hopefully, this will solve the issues. Cleaning the tent after watering every time isn't my idea of efficiency 😅 Thanks for checking out my diary 🍃 ✌️
Likes
13
Share
@GrowerGaz
Follow
The plants are settling into their new shoes. They have just had water and elite 91 roots as there is some Greenhouse Bio Grow in the soil mix. I am going to try and make some KNF nutrients this week to boost the growth phase.
Likes
3
Share
@Enki_Weed
Follow
Aktueller Zustand der Pflanze (siehe Bild): Die Pflanze präsentiert sich aktuell in einem hervorragenden Zustand und entwickelt sich prächtig. Trotz der Herausforderungen, die wir im Laufe dieses Grows hatten, sind die Ergebnisse mehr als ermutigend. * Wuchsform: Die Pflanze hat sich sehr buschig und kompakt entwickelt, mit einer Vielzahl von gut ausgebildeten Seitentrieben, die alle dicht mit Blüten besetzt sind. Dies deutet auf eine exzellente Lichtausnutzung und eine gelungene Verzweigung hin, wahrscheinlich durch gezieltes Training in der Vegetationsphase. * Blütenqualität: Die Buds sind auffallend dicht und zeigen eine beeindruckende Harzproduktion. Die Trichome sind bereits deutlich sichtbar und glänzen, was auf eine hohe Potenz und Aromaentwicklung hindeutet. Die Stigmen (Blütenhärchen) sind größtenteils bernsteinfarben verfärbt, was auf eine fortgeschrittene Reifephase hinweist und die bevorstehende Ernte ankündigt. * Blattgesundheit: Die Blätter sind weiterhin größtenteils grün und vital. Einige der größeren Fächerblätter im unteren Bereich zeigen die für die späte Blütephase typischen Vergilbungen, da die Pflanze ihre letzten Energiereserven in die Blütenbildung umlagert. Dies ist ein natürlicher Prozess und kein Anzeichen für akute Mängel in diesem Stadium. Herausforderungen und Erkenntnisse aus diesem Grow: Wir hatten im Laufe dieses Durchgangs mit einer Volatilität des pH-Wertes zu kämpfen, die zeitweise nur schwer zu stabilisieren war. Dies führte zu der Notwendigkeit, den pH-Wert der Nährlösung häufiger anzupassen. Nach genauerer Beobachtung wurde die Hauptursache für diese pH-Schwankungen identifiziert: Algenbildung auf der Oberfläche der Steinwolle. Diese Algen konkurrierten nicht nur um Nährstoffe, sondern trugen auch maßgeblich zu den instabilen pH-Werten bei. Learnings für den nächsten Grow: Um die Algenbildung und damit die pH-Problematik zukünftig zu vermeiden, sind folgende Maßnahmen geplant: * Reduzierung der Steinwollwürfel-Größe: Es werden kleinere Steinwollwürfel für die Keimung und Startphase verwendet. * Einsatz von mehr Tonkugeln (Leca): Die Steinwollwürfel werden im nächsten Grow deutlich besser mit Tonkugeln abgedeckt, um die Oberfläche vollständig vor Licht zu schützen. Dies wird die Algenbildung effektiv unterbinden und somit zu einem stabileren pH-Wert beitragen. Ausblick: Trotz der aufgetretenen Schwierigkeiten bin ich mit dem aktuellen Zustand der Pflanze äußerst zufrieden. Sie ist ein starkes Beispiel dafür, wie widerstandsfähig diese Pflanzen sein können, wenn die Grundversorgung stimmt und auf Probleme reagiert wird. Ich freue mich auf die bevorstehende Ernte und bin gespannt auf die Qualität des Endprodukts.
Likes
5
Share
July 17 - another topping session! ✂️✂️✂️ July 19 - Little defoliation 💚
Likes
18
Share
Still bringing them in and out each day. They are filling in nicely. Also did some LST, bending, twisting and tying down of some side branches. Fed with slightly more than 1/2 dose of nutrient’s recommended
Likes
33
Share
@BADKUSS
Follow
Hello everyone, the plants are still very good, no deficiencies in sight and canopee rather homogeneous. the stretch is soon over and I'm going to be able to stop the growing fertilizer, for which is knitting, I finished and let nature now play ... Now place to photos ...
Likes
23
Share
@DevelGrow
Follow
Es ist fast geschafft ☺️! permanent marker im Dognabiscup wurde geerntet und hat schöne große Feste harzige buds geliefert,die nun für mindestens 7 Tage im Dryferm bag Trocknen werden! Für ihre Größe ein sehr gutes Ergebnis! Es hat Spaß gemacht und ich sage Mal keep Green and grow High ✌️🍀😉🍀
Likes
170
Share
@nonick123
Follow
Día 47 (03/03) Las señoras siguen su imparable Stretch. Solo mirarlas y disfrutar 😍😍😍🎉🎉🎉 Día 48 (04/03) Riego 1,25 Litro H20 + Wholly Base 2,5 ml/l + Solid Green 1,5 ml/l + Early Flower 0,75 ml/l de Gen1:11 TDS 960 PPMs - pH 6,26 Día 49 (05/03) Se empiezan a formar los erizos! 😍😍😍 Gorilla Cookies FF ha despegado hacia el cielo! 🚀 Día 51 (07/03) Riego 1,25 Litro H20 + Wholly Base 2,5 ml/l + Solid Green 1,5 ml/l + Early Flower 0,75 ml/l de Gen1:11 TDS 950 PPMs - pH 6,37 Día 52 (08/03) Los erizos empiezan a engordar! Día 53 (09/03) Parece que el stretch se frena un poco... 💦Nutrients by Gen1:11 - www.genoneeleven.com 🌱Substrate PRO-MIX HP BACILLUS + MYCORRHIZAE - www.pthorticulture.com/en/products/pro-mix-hp-biostimulant-plus-mycorrhizae 🎚️Controlled by TrolMaster TCS-1 Tent-X System Main Controller - https://www.trolmaster.com/Products/Details/TCS-1
Likes
37
Share
@Kirsten
Follow
So the plants survived without light in my garage for 2 days, thank goodness! FBP2 is the best plant by far. She had stacked lots of tight buds, orange pistils coming in nice. Nice bushy structure to her. Super happy with her progress. Royal Critical is doing great, progressed further than all the others so far, lots of orange pistils, curling inwards towards the buds, still white pistils too, so not ready obviously. Not as dense a structure as FBP2, but much better than FBP1 and FBP3, which you can see are way behind both the others. They're looking super straggly. Not sure that they'll improve much at this stage unfortunately. Still I'm pleased overall with this grow, as it's my first and I have learnt a lot about the necessity for LST, and genetics being different from plant to plant. Hopefully we'll be able to harvest the Royal Critical here soon, then FBP2. As for the other 2 plants, I guess I'll have to wait and see.
Likes
7
Share
@Mr_BFL
Follow
bloom, swell, with problems with salting. Lemon after 1-2 weeks on Harv, today I will start to rinse
Likes
3
Share
@Ticfusama
Follow
End of week 7(day 50 to be exact). Her buds are starting to put on lots of mass. At this point only the buds in the center of the scrog are still upright on their own. I backed down on my light intensity a bit (on day 46) as she started to foxtail on me a little. Was running about 1600par in the convergence area between the two lights and about 900 on the edges. Backed the lights down to about 550(center) and 375(edges). She has been liking it and has stopped yellowing. She will be on this light intensity for the last couple of weeks. Trichomes are still mostly clear with a few cloudy/amber, so she will definitely be going the full 10 weeks. I backed down to half strengrh on her feed and added a good dose of epsome salt to give her a mag/sulfur boost ti promote ripening. She smells amazing. Earthy dank with a strong overtone of fruit. This pheno will be a breed mother for me in a couple of runs. The best clone is going to a homie's place to be kept in veg. He wants to run her too so we will take cuttings for cycles at his place and i will later when im ready to cross her.
Likes
7
Share
20/11 Ce petit se développe super vite, irrigation a l'eau uniquement tous les 2/3jours. Bientôt transplantation pots 6L pour plus de développement. Reste sur le réseau growers. 26/11 repiquer dans un pots de 6L dans du ATAMI - Janeco-Light Mix qui es super pour développer davantage de racine . Arrosage a l'eau ph 6,5.
Processing
Likes
12
Share
Checkout my Instagram @smallbudz to see the Small budget grow setup for indoor use, low watt, low heat, low noise, step by step. 04/01/2020 - Did the last defoliation, removed about 1/4 of plant material. 06/01/2020 - Fed her 1.5l of 6.5PH water with 0,3ml Cal Mag (Atami) 0,25ml of Grow, 0,6ml of Bloom and 0,5ml Max, and 1ml of each: Heaven, Alga-mic and Vera, noticed some run off, I use about 1/3 of the nutrient dosage on the chart, to achieve about 200/300PPM (500 scale).
Likes
Comments
Share
@BruWeed
Follow
☘️12/12 - Empieza su primera semana en etapa de crecimiento. ☘️Tiene 18 dias de vida desde que salio el plantin. ☘️Se encuentra perfecta, esta midiendo 15cm de largo y las chalas se encuentran bien. ☘️Ahora mismo se encuentra en una maceta de 10L. ☘️Va estar tres semanas en esta etapa para ya después entrar en flora. ☘️Estos días estare publicando mas imágenes de como viene. Podes seguirme en instagram como @bruweed_arg para mas contenido 🇦🇷☘️😶‍🌫️
Likes
25
Share
Nach der Ernte musste die SexBud nur geringfügig für die Trockenphase vorbereitet werden.