No fueron cosechadas todas al mismo tiempo. Unas empezaron floración primero que otras.

Hey guys! TheIceCreamParlour has been on a little break while we made some major refurbishments. The first 5 plants are now hooked up to the system and we are ready to go. These girls were transplanted yesterday into 6" Cultilene blocks with floraflex feeding blocks on a 12 hour feeding system. Fertigation takes place every half hour for 20 seconds meaning fresh oxygenated solution is being replenished frequently. I'll keep this diary as simple as possible considering it's the first test of my home made feed system.

Great week decided to give big bloom and grow big fox farm. They LOVED IT! I cut dosage in half for half gal watering can. We just bought a clone also gorilla glue Update my husband decided to defoliate it some. Will post pictures tom after feeding

FLOWERING STARTS In the the new marshydro set-up 120x120x200 4'x'4 FC-4800 lamp Pubes are showing on all of them happy days in the absolutely amazing marshydro tent 👌🏻💯👌🏻 and no balls in the room yet so that's good at least i know that first grow i had issues with hight but with my 120x120x200 that not going to be end problem so stretch like ya never stretch before 💪🏻 i am prepared now lol the FC-4800 is a beast and still tweaking hight dimmer don't want to burn them but also want to utilize the lamp as much as I can but will get under control 🤘🏻😎🤘🏻 1/11/21 Did some last defoliation and spread the plants out bit Tru the tent got lamp dialed in dimmer around 55% and hight around 45cm above the plants and every week will bump up the dimmer with 5% they are looking very good healthy and i am very proud of the results so far gave the proper nutrients and the normal watering in between everything cool in the hood Will be updated soon happy growings Growmies visit www.marshydro.eu for your best gear and use the PROMO CODE: DEVILSBUD Some info about the Marshydro FC-4800 Superb Quality LED Chips: The whole light is composed of 1206 pcs Samsung lm301b and Osram 660nm chips. More than two times as many LEDs are used to drive the grow lights at low currents and to avoid overdrive. Quality is guaranteed and efficiency is up to 2.8 μmol/j. Even PAR Distribution and High PPFD Output: The multi-light bar design and the densely distributed light chips enable the LED grow lights to achieve the optimum PPFD required for plant growth over the entire effective coverage area. Specifically Designed Spectrum: To ensure even plant growth, blue and red light are enhanced on the basis of a full spectrum combination. Not only does this accelerate plant growth, but it also improves the yield and quality of the plants at the same time. Dimming Daisy Chain Function: The dimming function saves on electricity costs and enables brightness from 10% to 100% for the different stages of plant growth. A single master light can connect up to 30 lights in a daisy-chain system. Business LED Grow Light: The light's wavy heat sink dissipates heat quickly and the IP65 waterproof allows the light to operate in humid conditions. 180° collapsible feature for easier installation. All these features provide favorable assistance for commercial cultivation. And some tent info ●【Lock All Light Insid】MARS HYDRO Grow Tent Interior is made of diamond mylar. Non-toxic to the environment, no harm to plants. High-quality 1680D canvas being double stitched, (ALL OTHERS BRAND grow tent is 601D canvas) which is tear-proof for perfect light locking, No light leaks or rips at all. ●【Durability Grow Tent】Stable Metal corner adapters and poles are the trustful supporters of the tent. No rusting nor paint-falling. Quick easy tool-free installation. Carries strong heavy-duty SBS zippers, double layer lining to create a light-proof seal. ●【Easy Observation of your Plants】Special peeks window made by double layers of cloths. Observe the growing conditions of your plants without opening the tent and avoid disturbing plants. The peek window also serves to dissipate heat and ventilate air. ●【Removable Tray Keep Clean】The package includes a removable waterproof floor tray to hold soil and fallen leaves. The tray can be taken out easily to wash. Removable and water-proof makes cleaning easy. ●【Good Ventilation&Fast Assembly】 Circular double-sleeved vent holes with adjustable nylon strap for air circulation by exhaust fan, ducting, carbon filter, or reflector. Better allows proper light, heat, and airflow. Quick tool-free installation. Reinforced by a sturdy metal frame to ensure security and stability, supports up to 140lb. Perfectly safeguard your plants to thrive even in winter

~ FASTBUDS TESTER #2202 ~ Well friends, here we go on another 'canna-venture' together! The grow room has had a complete remodel and some upgrades done to it including brand spanking new 4x8 and 4x4 tents and a Trolmaster Hydro X controller along with a new Control Panel. This tester strain is one of six tester strains that FastBuds has graciously provided me with and I'm looking forward to seeing what this girl has to offer when she's grown to her full potential! One drawback of 'testers' is I have little to no information on it other than its number and that it's an autoflower... 🤪 But, it's ALWAYS a blast growing them for me because not knowing a lot allows me to just concentrate on the essentials: Light, Environment, Water, Nutrients and possibly a bit of LST... not complicated, just basics like keeping a constant temperature and RH in the tent at a level that gives a good VPD, watering when almost dry and maintaining proper light levels according to their stage of growth. ____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ~THE SETUP~ ~Initially seeds were lightly scuffed, then soaked for 3 hours in 78℉ distilled water after which they were transferred to moist paper towels laid out in a Jiffy Pellet plastic starter tray with lid. Underneath the tray was placed a Vivosun Heat Mat with Controller that was set to 78℉ where they stayed until their tap roots emerged. ~Planted into Jiffy Peat Pellets that were hydrated with distilled water warmed to 78℉ with a 7.0 ph. ~Once roots emerge from the Jiffy Pellet they're transferred to their fabric pots. ~Grown 100% organic in a 4g Gronest fabric pot and a 3g fabric pot by Wraxly filled with Mother Earth 70/30 Coco/Perlite medium and initially amended with Dr. Earth 4-4-4 / Earthworm Castings / Dr. Earth Flower Girl 3-9-4 and Coast of Maine Stonington Blend Organic Plant Food 5-2-4. ~19/5 light cycle for the entire run with supplemental UVA added during flower. Lights are controlled by a Trolmaster Hydro X controller set for a 15min Sunrise/Sunset simulation. ~Top dressing every 3-4 weeks with slow release dry amendments and Earthworm castings. ~Straight water ph'd @ 6.2-6.8 when needed and bi-weekly Compost Tea's. ____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ Weekly Updates: 12/15- Here we go into the second week of veg for the FastBuds Tester #2202 girls and they're on a roll! The #1 tester has developed some discoloration on her leaf tips which tells me she's a bit sensitive to my amendment concentrations so remember to go very light on the nutrients when you start out! I'll keep an eye on her but really am not too concerned at this time. When I checked on them today they both were still moist so I let them go until I check them tomorrow. Basically at this point in the run all I have to do is make sure they don't dry out, fill the humidifier and watch them grow! 12/17- Yesterday I watered them both and increased the amount to roughly 0.25g each of de-chlorinated water with 3ml/g of Botanicare Silica Blast (added to begin to help strengthen their branches) and then ph'd to 6.4 @ 74℉. I've also increased the output of the HLG 650R's to 35% which equates to about 230w at the wall which, of course has raised the temp's in the tent so I've also begun to run the A/C unit in the grow room which is keeping the temp's now at 75℉ in the tent. The RH is running around 75-78% RH giving a VPD of .67-.74 which I'll take! 😁👍 Other than what I've mentioned above, all I did was fill the humidifier with distilled water and watched my girls grow! 🤩 12/19- Today I watered them each with 0.25g of de-chlorinated water to which I added 3ml/g Fish Head Farms Fish Sh!t and 1 tsp/g Unsulfured Molasses which I then ph'd to 6.3 @ 74℉. I'm now watering through the bottom, filling the drip pan and letting the plant draw up the water into itself. I am also watering from the top, but only just enough to moisten the medium. They're really starting to take off now, a sure sign their roots are beginning to get well developed. Their 4th set of leaves have emerged and I'm thinking over topping them in the next day or so. 12/21- Well, yesterday I went ahead and topped the #2 Tester #2202 taking off the 5th leaf set. Hopefully she won't stress out over this and starts shooting out those secondary branches. I left the #1 alone as she's not quite as vigorous as the #2. I may not top the #1 as a sort of comparison to see how each grows out. Today I watered them both with 0.25g of straight de-chlorinated water each which was ph'd to 6.3 @ 74℉. I gave about 3/4 of it into their drip pans so they can draw it up into their medium, the rest I applied to the top of their medium just to moisten it. Well there's two weeks of veg behind us now, Week Three of vegetation is beginning and they should really start to take off! 😍👍 😎💚 Thank you for checking out my passion in life! Please visit as often as you wish and I hope you enjoy this journey as much as I know I will! Grow Strong! 💪😎🤙

Harvest in week 12. But I screwed up, I didn't have enough room to separate each variety, so I would put an average weight when everything was dry... I had done everything well, I had to mistake on the place of the drying bag Last pictures, mixed buds

The wedding glue from @fastbuds is coming along amazing the colors an the trichrome production on this strain is beautiful with nice big dense nugs an the Gelato auto from @herbies is coming along starting to bud up really nice an starting to build up some frost

Day 36. The plants are in pre flowering stage. The plants are tall 25 cm about except one of them that is 60cm.

Moving right along, each girl is on her own pace. Tent was so crowded I had to remove the heater therefore I bought a bigger tent and will use use this one for drying. Thanks for looking..

The buds are very tight, but they didn't grow large colas so that means wasted time trimming cannabis, which I am not a huge fan of. I will not be growing this strain again, as I believe there are far better breeders and strains out there. I will continue to seek out the best breeders and strains until I am satisfied. I believe this Auto will yield in the 16-22 Ounce range dry, so I am not super disappointed, but I know I can do much better than this. After 6 days of drying, it took me around 7 hours to trim this auto, and she ended up yielding 16.72 Ounces. So she was definitely on the lower end of the spectrum from what I estimated on chop day, but still in the range. The buds are very tight, and smell like like cheese. I am only running one mature auto at a time now, so next up will be the Acid Dough from Ripper Seeds. I hope everyone has a great rest of your weekend, stay safe and Blaze On!!

Na

Starting flush

12/8/21 - Wow! They are popping! The humidity is still high but we’ll get it under control. 12/9/21 - They look really good! Stretch is under control now. They are flowering hard right now. We ordered a dehumidifier as we don’t want any mold. 12/10/21 - Looking good. They are bulking up by the day. Still feeding as they get dry. We gave them a feeding today. See pics from today and yesterday. 12/11/21 - The ladies are showing off. Frost is starting to form! See today’s video. Dehumidifier will be here in a couple days. 12/12/21 - Looking good! We are very excited for the buds to be showing off so early. This week will be the last with Beastie Bloomz. Then we run Cha Ching until harvest. 12/13/21 - A little humid but looking great. Dehumidifier will be here tomorrow HOPEFULLY. We really need to dial back to 45%. See todays pics! 12/14/21 - The dehumidifier is supposed to be here today. We will set it to 45% and hopefully that calms down the humidity. Other than that the plants are looking amazing! We are heading to week 5 of flower tomorrow :)

Hey guys :) The girls got topped once now, they still recovering from the light burn i did, Trying to ‚LST‘ 😄 Started giving nutes in a Half dosage at week 3 !

Día 71 (30/12) Christmas holidays. Only watering Día 72 (31/12) He recibido mi nueva lampara Mars Hydro FC1500 EVO Led Grow Light (2024 NEW FC 1500-EVO Samsung LM301H 150W LED) - https://marshydro.eu/products/fc1500-evo-led-grow-lights/ - https://www.amazon.de/dp/B0CSSGN5D8?ref=myi_title_dp Procedo a instalarla, de modo que tengo la tienda de 120x60 cm perfectamente cubierta con las DOS (2) lámparas FC1500 EVO Es ideal tener dos lámparas, porque así puedo ajustar la distancia a la lampara en función de la altura de capa planta Ajusto ambas lámparas al 75% de potencia (Total 225W), que es más que suficiente para cubrir el área de 120x60 cm Día 73 (01/01) CBD Auto 20:1 #1 - Muestra una ligera deficiencia con algunas puntas de las hojas dobladas hacia arriba y clorosis... Creo que le voy a dar otra ración de BIO PK 5-8 OG Kush Auto - Está apilando cogollos de forma brutal. Increíble el olor y la cantidad de tricomas que está formando 😍 Día 74 (02/01) CBD Auto 20:1 #1 - Se empiezan a formar tricomas entre los incipientes cogollos OG Kush Auto - Una pena que se haya intensificado la deficiencia de CalMag... en las hojas, porque los cogollos son gordos y densos, y cubiertos de tricomas Día 75 (03/01) CBD Auto 20:1 #1 - Voy a darle un boost para las 4 semanas que le quedan hasta la cosecha con SILICIUM FLASH Hago un pequeño agujero cerca del tallo, espolvoreo 25g de SILICIUM FLASH en el agujero, lo cubro de tierra. Riego con una solución de 2g de BACTREX por litro de agua. OG Kush Auto - Impresionante densidad de los cogollos que empieza a doblar las ramas 😍 La ventana de cosecha se acerca! 💥 Día 76 (04/01) CBD Auto 20:1 #1 - Investigando me doy cuenta de que lo que le pasa es quemadura de luz, ya que la parte externa de la planta sufre clorosis, y la parte interna (donde no alcanza la luz) está completamente verde Ajusto la lampara sobre esta planta para 40 DLI OG Kush Auto - Sigue poniendo los cogollos duros como rocas y muy llenos de tricomas! 😍💥 Día 77 (05/01) CBD Auto 20:1 #1 - On going OG Kush Auto - Empieza la senescencia en las hojas de abanico, acelerada por la deficiencia de CalMag... que ha tenido. 💦Nutrients by Bio Tabs - www.biotabs.nl/en/ 🌱Substrate PRO-MIX HP BACILLUS + MYCORRHIZAE - www.pthorticulture.com/en-us/products/pro-mix-hp-biofungicide-plus-mycorrhizae "GDBT420" 15% DISCOUNT code for the BIOTABS Webshop https://biotabs.nl/en/shop/ With 2 x Mars Hydro FC1500 EVO Led Grow Light (2024 NEW FC 1500-EVO Samsung LM301H 150W LED) - https://marshydro.eu/products/fc1500-evo-led-grow-lights/ - https://www.amazon.de/dp/B0CSSGN5D8?ref=myi_title_dp

Really love this strain, grown it a few times, happy with how she turned out, greasy an sticky and the smoke is heavy an euphoric, she smells like fruit punch with hints of nut meg, a smell I can't explain very pungent...